Haier AS25S2SN1FA-NRC User manual

Please read this operation manual before using the air conditioner.
Keep this operation manual for future reference.
SPLIT TYPE ROOM AIR CONDITION
OPERATION MANUAL ER
N
AS25S2SN1FA-NRC
AS50S2SN1FA-NRC
AS35S2SN1FA-NRC
0011500387
danish

WARNING:
·If the supply cord is damaged, it must be replaced by the manufacturer,its service agent or
similarly qualified persons in order to avoid a hazard.
·This appliance can be used by children aged 8 years and above and persons with reduced
physical, sensory or mentao capabilities or lack of experience and knowledge if they have
been given superivision or instruction concering use of the appliance in a safe way and
understand the hazards involved. Children shall not play with the appliance. Cleaning and
·The wiring method should be in line with the local wiring standard.
user maintenance shall not be made by children without supervision.
All the cables shall have got the European authentication certificate. During installation, when the
·connecting cables break off, it must be assured that the grouding wire is the last one to be broken off.
The explosion-proof breaker of the air conditioner should be all-pole switch. Distance between its two
contacts should be not less than 3mm. Such means fordisconnection must be incorporated in the
·Make sure installation is done according to local wiring regulation by professional persons.
·
·A leakage explosion-proof breaker must be installed.
Make sure ground connection is correct and reliable.
Read the precautions in this manual
carefully before operating the unit. This appliance is filled with R32.
Do not use means to accelerate the defrosting process or to clean, other than those
recommended by the manufacturer.
·
Keep this manual where the user can easily nd it.
The appliance must be stored in a room without continuously operating ignition sources (for
example: open flames, an operating gas appliance or an operating electric heater).
Do not pierce or burn.
·
·Be aware that refrigerants may not contain an odour.
·The appliance must be installed, operated and stored in a room with a floor area larger than
3 .
·
·Do not use a refrigerant other than the one indicated on the outdoor unit(R32) when installing,
moving or repairing. Using other refrigerants may cause trouble or damage to the unit, and
personal injury.
wiring.

16
1
3
15
12
C o n ten ts
PARTS AND FUNCTIONS
OPERATION
INDOOR UNIT INSTALLATION
MAINTENANCE
CAUTIONS
TROUBLE SHOOTING 17

Parts and Functions
Wi-Fi function description
1
The system architecture diagram
The application environment
Smart mobile phone and wireless router are necessary for the appliacation.
Wireless router must be able to connect to the Internet.
Smart mobile phone requires IOS or Android system:
IOS system
must support IOS 9.0 or above
Android system
must support Android 5.0 or above
Configuration method
Scan the QR code below to download “hOn” APP.
Other Download options: Please search hOn APP on:
· App Store (IOS)
· Google Play (Android)
After App Download, please register, connect the air conditioner and enjoy using hOn
to manage your device. Please refer to the HELP section inside the APP for more details
about how to register, connect the unit, and other operations.
·Huawei AppGallery (Android)
1

Outlet
Horizontal flap
Display board
(adjust up and down air flow
Don't adjust it manually)
(adjust left and
ow)
Vertical blade
Emergency
Switch
right air fl
Inlet
Air Purifying Filter
(inside)
Inlet grille
(inside)
Parts and Functions
Indoor Unit
Outdoor Unit
Remote controller
Outer side of the controller
OUTLET
CONNECTING PIPING
AN
D
EL
EC
TR
IC
A
L
WIR
IN
G
INLET
DRAIN HOSE
4
Actual inlet grille may vary from the one shown in the
manual according to the product purchased
1.
SELF CLEAN button
2.
DRY button
3.
COOL button
Used to set COOL operation.
4.
5.
n
.
6
o
i
t
c
n
u
f
h
c
a
e
f
o
y
a
l
p
s
i
D
status
8.
Wi-Fi and CLOCK display
7.
Operation mode display
9
.
TEMP
display
10.
Humidity display
11.
F
AN SPEED display
F
12.
SWING display
Swing up/down display
swing left/right display
14.
TURBO button
15.
QUIET button
16.
HEAT button
17.
FAN button
Used to set DR
Y operation.
13.
TIMER ON display
TIMER OFF display
CLOCK display
1
4
5
6
7
89
10
11
12
13
15
16
17
14
TEMP
button
used to change setting
temperature
ON / OFF button
2
NOTE:
a. Humidity display is unavailable on some models
b. If the model you buy has a Wi-Fi function,press the“ON/OFF”
button for 5s to emit theWi-Fi binding signal. Once in the
binding mode, the APP will show how to bind.
TIMER
3
2
SELF CLEAN
TURBO
Display board
Signal receiver hole
COOL display
HEALTH display
4
2
3
1
5
DRY display
6
Ambient temp.display
When receiving the remote
control signal, display the set
temperature.
2
35
6
4
HEAT display
1

Operation
Clock set
Note:
Note: The distance between the signal transmission head and
the receiver hole should be within 7m without any obstacle
change-over wireless telephone is installed in the type
in receiving the signals, so the distance to the indoor unit
should be shorter.
Full display or unclear display during operation indicates the
batteries have been used up. Please change batteries.
If the remote controller can’t run normally during operation,
please remove the batteries and reload several minutes later
.
Hint:
Remove the batteries in case unit won’t be in usage for
a long period.
20. SMART button
special heating set
function: 10 degree
heating maintaining
(valuable for RS)
18. buttonTIMER
23. SWING up/down button
24. SWING left/right button
19. buttonCLOCK
26. HEALTH AIRFLOW button
21. HEALTH button
28. CODE button
A-b yard
29. APPLY button
30. 10°C button
25. SLEEP button
22.
27. LIGHT button
Control the lightening and
extinguishing of the indoor
LED display board.
Press CLOCK button,
Press “+” or “-” to set
correct time.
Each press will increase or
decrease 1min. If the button is
kept pressed, time will change
quickly.
press APPLY, “TIME”
starts
1
2
3
1. Press “HEALTH”+“HEALTH AIRFLOW” simultaneously can
set and cancel the “LOCK” function ( )
FAN MODE button
19
20
21
22
23 24
25
26
27
28
29
30
18
FAN MODE
FAN MODE
working.
SMART
10
SMART
10
ON/OFF
ON/OFF
3

COOL,HEAT and DRY Operation
1.
In DR
Y
mode, when room temperature becomes
Y
lower than temp. setting +2 ºC, unit will run
intermittently in LOW speed regardless of
F
AN
F
setting.
2.
Remote controller can memorize each operation
status. When starting it next time, just press ON/
OFF button and unit will run in previous status.
You can use this function when silence is needed for rest or
reading.
For each press, is displayed Air conditioner starts
QUIET function operation. In QUIET operation mode, fan
speed automatically takes low speed of AUTO fan mode.
Press QUIET button again, disappears, the operation
stops.
QUIETQUIET
When you need rapid heating or cooling, you can use
will show ,and then achieve to turbo function.
this function. Press button,the remote controller
Press again this TURBO button , the turbo function will
be cancelled.
QUIET
4
TURBO/QUIET Operation COOL,HEAT and DRY Operation
Operation
QUIET
Unit start.
Select operation mode.
Press the COOL
button on
Press the COOL
the remote controller.
Press the HEAT button on the remote controller.
Press the DR
Y button on the remote controller.
1
2
TURBO
TIMER
SELF CLEAN
TURBO
TIMER
SELF CLEAN
TURBO
TURBO
TURBO
3

Operation
4
Unit will start running to reach the
temp. setting on LCD.
AN Operation
AN Operation
changes as follows:
Unit will run at selected fan speed.
button.
pressed, temp. setting
increases 1
ºC.
pressed, temp. setting
decreases 1
ºC.
1
21
SELF CLEAN
TIMER
SELF CLEAN
TURBO
TIMER
SELF CLEAN
TURBO
SELF CLEAN
Functional description:
the purpose of this function is to clean the evaporator.
Entry and exit
Press SELF CLEAN button to enter this function, then
it will display "CL" on the panel of the indoor unit and also
on the remote controller. Maximum running time not more
than 25 minutes, this function will exit automatically with
the " Pi " sound twice, then the unit return to original state.
Under operation process of SELF CLEAN, press the button
repeatedly is invalid and cannot exit, please press the
“power” button or swift to other mode to exit.
Note:
1.This function is invalid in timer / sleep mode.
2.After this mode starts, the air volume may reduce or
even have no airflow,or even cold airflow blowing.
3.It is normal if the unit make some sound like expand with
heat and contract with cold
4. The “CL” display time may last differently on the remote
controller and panel.
5.If the outside ambient temperature below zero, error
code “F25 “may be occurred during self-cleaning operation ,
which is normal protection, please turn off the power
and to restart after 10 seconds .
6.The best condition to run this mode: the temperature is
20 ~27 and the humidity is 35 ~60 in the door,
the temperature is 25 ~38 cooling season out the
door.
7.It is hard to frost if the air is too dry(humidity 20%). and
if the humidity is too high(humidity 70%).the condensate
water may increase, which may move away some frost.
TURBOTURBO
5

and outlet grills of the air conditioner are opened, and
the unit goes on working under the condition before the
grille will close automatically
.
Notice:
Cannot
pull
direct the outlet
grille by
hand. Otherwise,
the
grille will run incorrectly
. If the grille is not run correctly
,
stop for a minute and then start, adjusting by remote
controller
.
Remote controller can memorize each operation status.
when starting it next time, just press ON/OFF button and
unit will run in previous status.
The setting of
function
The cancel of
function
Operation
appears on the display
.
A
void
A
A
the body
.
again,
appears on the display
.
direct to the body
.
Note:
2.
In heating, it is better to select the
mode.
3.
In cooling, it is better to select the
mode.
4.
In cooling and dry
, using the air conditioner for a
long time under the high air humidity
, a phenomenon
falling drips of water occurs at the outlet grille.
5.
Select the appropriate fan direction according to the
actual conditions.
FAN MODE
HEALTH AIRFLOW Operation
TIMER
10
SMART
3
6

SWING Operation
T
o cancel
T
T
TIMER mode
Just press
TIMER
button several times until
TIMER
dispiay disappear.
Operation
Set Clock correctly before starting
T
imer operation.
Y
ou can
Y
Y
let unit start or stop automatically a following times: Before
you wake up in the morning, or get back from outside or
after you fall asleep at night.
mode.
T
ime setting.
Remote controller: “
TIMER ON
”
Remote controller: “
TIMER OFF
”
“
ON
” or “
OFF
”
Every time the button is pressed,
time setting increases or decreases
Select your desired
TIMER ON.
Select your desired
TIMER OFF
.
TIMER Operation
1
1
2
. It can be
adjusted within 24 hours.
APPLY
Select your desired operation
3
COOL/DR
Y
:
For each press of “
” button, air
displays as follows according to
dif
ferent operation modes:
dif
dif
Wh
en
hum
id
ity
is h
ig
h
,
con
d
e
n
sa
t
e
wat
er
m
ig
ht
oc
cu
r
at air outlet if all
vertical
louvers are adjusted
to left or
right.
position for a long time in COOL
or DR
Y
mode,
Y
otherwise, condensate water might occur
.
1
2
HEA
T
T
HEA
HEA
:
SMAR
SMAR
T
:
Initial state
Initial state
For each press of “
” button
, remote controller
displays as follows:
remote controller:
FAN MODE
FAN MODE
FAN MODE
FAN MODE
better air circulation
TIMER
TIMER
10
SMART
SMART
10
AUTO
7