Haier ESA312 User manual

0010551962

English

English

1
1
2
4
4
5
5
6-7
8-12
8
8-12
13-18
14
14
15-18
19-20
20-21
22
English

English
Test power plug before each use:
1. Press ìreset ìbutton.
2 . Press ìtest ìbutton, unit should trip.
3. Press ìresetî button again for use .
Do not use if above test fail.
In the event this device trips , the cause of the malfunction is to
be corrected before further use of the device .
Important:

English

English
24
You have 3 levels of Fan Speed to set at your
desired comfort level. HIGH, MED and LOW.
You can run the fan only on not so hot days. The
fan can be set to run at 3 speeds (HIGH fan, MED
fan, LOW fan)as desired by you.

English
12. Electrostatic Filter (not all models)
Being constructed of high efficiency purifying
substance, active carbon fabric, electrostatic fabric,
electrostatic active carbon net and other materials
it purifies the air effectively. Its wavy structure
increases the capability to filter dust and smoke
effectively. Due to the retention of the active carbon
it has a high purifying speed capable of
strong airflow.
The Fresh Air Vent allows the air conditioner to
recirculate inside air, draw fresh air into the room
and exhaust stale air to the outside .

English
Remote control and control panel operations

English
Every time you press the MODE button, it will change between FAN, COOL, ENERGY
SAVER and DEHUM. (See Fig. # 3)
Having set the temperature you will set the function of the air conditioner.

English
Once the function mode is decided you will have to set the fan speed.(See fig. #4)
Every time you press the SPEED button, fan speed will change between LOW,
HIGH,MED.
1) If you choose the COOL mode you can run the fan in one of the 3 speeds HIGH,
MED, LOW.
2) For cool days you may want to run the "FAN" function. The fan can be set to run at
3 speeds (HIGH fan, MED fan, LOW fan)as desired by you.
4)Energy Saver : The unit runs the same as COOL setting in the ENERGY SAVER
mode. But the fan will be off 3 minutes after the compressor cycle off.

English

English
Vent Control Operations
For maximum cooling efficiency,
CLOSE the vent. This will allow
internal air circulation.
OPEN the vent to discharge stale air.
Adjusting the Air Flow Direction
Airflow can be adjusted by changing the direction of the air conditioner's louvers.
This can also increase the cooling efficiency of the air conditioner.
Adjusting Horizontal Air Flow
Direction
Adjusting the vertical louvers left and
right will change horizontal airflow.
Adjusting Vertical Air Flow Direction
Adjusting the Horizontal vane up and down will
change vertical airflow. The vane can be adjusted
by nudging the back or up and down of the vane.
Adjusting Horizontal Air Flow Adjusting Vertical Air Flow
Recommended orientation of louvers
Adjust louvers to face upwards when cooling to maximize cooling efficiency.
Fig. # 5
OPEN
CLOSE

English

Window seal
gasket
Curtain sash screws
31/32"
English
Parts
PartsSupplied
Remote
control
ìCR2025ìbattery
Top rail
Frame guide
Model: HWR10XC5, HWR12XC5, ESA3105, ESA3125
Drain tube
Curtain
attachment
screws 13/32"
Leftand right
sidecurtains
Basepan angle

English
Installing Unit into A Window
Window Opening Requirements
The air conditioner is designed to fit into double or single hung sash type windows. Each of the
units comes with an installation kit that provides adjustable mounting louvers, to fill the gaps
between the sides of the unit, and the window frame. The chart below reflects the dimensions of
the units with, and without installation kits. Measure your window opening width and compare
it to the chart below to ensure that it meets the minimum and maximum window width requirements.
Model
A(inch)
Dimension
B(inch)
C(inch)
D(inch) Max
Case High
Case Width
D(inch) Min
Case Depth
HWR10XC5, HWR12XC5, ESA3105, ESA3125
HWR10XC5, HWR12XC5,ESA3105, ESA3125
ModelsHWR10XC5,HWR12XC5,ESA3105,ESA3125
Unpack unit on floor next to installation location.
1. Open the inlet grille by pulling the exposed door on
the top of the unit and remove the screw which fasten the
front panel. (Fig. A)
2. Remove the front panel and rotate it to B position.
Separate operation panel from the front panel by pushing
the tabs. (Fig. B)
PREPARE UNIT
FOR
INSTALLATION-1
1
Fig. A
Fig. B
A
B C
D
Tabs
832
21
"
"
15 16
9
39
27
14 32
31
23 8
5
22 16
7"
"
"
"
"
"
15 16
15

1. Remove the screws which fasten
the cabinet at both sides and at
the back.
2. Slide the unit from the cabinet
by gripping the base pan handle
and pulling forward while bracing
the cabinet.
3. Insert the Frame Guide into the
bottom of the cabinet.
Caution: Never expose plastic
front or grille to extreme
temperatures.
PREPARE UNIT
FOR
INSTALLATION-2
2Shipping
Screws
Install top rail with three 13/32"screws.
Slide left-hand curtain assembly
into left end of top and bottom
rails. Repeat for right-hand curtain
assembly. Fasten curtain retainer
strips to sides of outer case with
eight 13/32" screws.
ASSEMBLE
CURTAINS/TOP
RAIL
3
English
Inspect window track, sash, and sill
for its ability to support the weight of
air conditioner.
Measure width between window
moldings to ensure Instant Mount
will fit window frame. Instant Mount
models are designed for windows
wide (the detail see page 15)
Instant Mount kit supplied with unit
is designed for mounting in most
double-hung windows without
storm windows. For installation in
window frame with storm window,
modify sill by adding wood strips (not
included) to inner and outer sills. This
raises unit and eliminates
interference of storm window frame.
Mobile home window installation
Add wood strip (at least11/2"wide)
along entirewidth of window sill.
Thicknessof wood strip shouldmatch
heightof front lip on window frame.
Fastenwood strip to sill with a
minimum of threecountersunkwood
screws(not suppliedwith kit). This
providesa smooth surfacefor
mountingair conditioner.
Storm window installation
If stormwindow framedoes not allow
adequateclearancebelow sill (1/2"
required),remove stormwindow
frameor createclearanceby adding a
wood strip (at least11/2"wide) along
entirewidth of sill. Fastenwood strip
to sill with at leastthreecountersunk
wood screws(not suppliedwith kit).
Thisprovidesa smooth surfacefor
mountingair conditioner.
SI LL
Wood
Str i p
1/2"
Min imum
O
U
T
D
O
O
R
St orm Wi ndo w
Fram e
11/2"
Min imum
I
N
D
O
O
R
11/ 2"
Minimum
Wood
St rip
I
N
D
O
O
R
O
U
T
D
O
O
R
Window
Frame
Mus tbe amini mum
of 1/2" to cl ear
botto mrail on unit
PREPARE
WINDOW FOR
INSTALLTION
4

Placeoutercaseinwindow.Lower sashuntilitrestsbehindfrontflange oftoprail.Bottomrailmustrest behindwindowsill.
Curtainassemblycut awayforclarity.
Use3screws(31/32")tofixthecasetowindowssash.
Expandbothcurtainstocontactthe windowframe.Attacheachcurtain thewindowsashusing31/32"screws.
NOTE: Tomakescrewseasierto drive,drillapilotholeintosash throughclearanceholeincurtains.
Top rail
Bottom rail
About
5∞
INSTALL OUTER
CASE IN WINDOW
5
English

8
Find someone to help you
replace chassis in outer case.
Replace front panel, and grille.
(Don't forget to install the attachment
screws before replacing grille)
Caution:
For security purpose, reinstall
screws at cabinet's sides.
Important:
Because window
sash helps keep unit in window,
make certain window sash contacts
outer case before reinstalling chassis.
RETURN
CHASSIS TO
OUTER CASE
English
Installsashbracketontopofindoorwindowsash withonewoodscrew31/32"topreventraisingof windowfromtheoutside.Screwanchordirectlyinto sideofwindowframe.Forhardwoodormetalwindow frames,drillapilotholetostartscrew.
Important:Becarefulnottodrillpilotholetoodeep. Addapieceoftapetothedrillbitasadepthgauge. Alsostayclearofglass.Becarefulnottodamagethe functionofthewindow.
Cutwindowsealgaskettowidthofwindow.Stuffwindow sealstripbetweenoutdoorwindowglassandtopof indoorsash.Thiswillstopairleakagewhichreduces efficiency.
6
INSTALL SASH BRACKET
& SEAL GASKET
INSTALL
DRAIN TUBE
7