Haier ESAX3186 - 17,000 BTU In-Wall Air... User manual

Air ConditionerEdition:2005/12/28
OPERRATION

TEMP/TIME
MODE SPEED TIMER
ON/OFF
Remote control and control panel operations
Air ConditionerAir Conditioner
Air ConditionerEdition:2005/12/28

TEMP/TIME
MODE SPEED TIMER
ON/OFF
Every time you press the MO E button, it will change between FAN, COOL, ENERGY
SAVER and EHUM. (See Fig. # 3)
Having set the temperature you will set the function of the air conditioner.
Air ConditionerEdition:2005/12/28Air ConditionerEdition:2005/12/28Air ConditionerEdition:2005/12/28

3) If you choose to use the ehumid function. This will remove excess moisture
from the air on excessively humid days.
Tr: temperature inside the room.
Ts: the set temperature.
1 ) When Tr>Ts+3 oF, the compressor will run continuously the fan at the
selected speed.
2)When Ts-1 oF¡Tr¡Ts+3 oF the compressor will cycle for 10 minutes on
and 6 minutes off.
3)When Tr<Ts-1 oF, the compressor will shut off.
The dehumidification process takes place between the set temperature -1
and 3 oF above the set temperature.
TEMP/TIME
MODE SPEED TIMER
ON/OFF
Once the function mode is decided you will have to set the fan speed.(See fig. #4)
Every time you press the SPEE button, fan speed will change between LOW,
HIGH,ME .
1) If you choose the COOL mode you can run the fan in one of the 3 speeds HIGH,
ME , LOW.
2) For cool days you may want to run the "FAN" function.
The fan can be set to run at
3 speeds (HIGH fan, ME fan, LOW fan)as desired by you.
4)Energy Saver : The unit runs the same as COOL setting in the ENERGY SAVER
mode. But the fan will be off 3 minutes after the compressor cycle off.
Air ConditionerEdition:2005/12/28Air ConditionerEdition:2005/12/28Air ConditionerEdition:2005/12/28

Timer on or Timer off mode is used to pre-start or shut off your unit in
advance. You can program this up to 24 hours in advance. You can use
the Timer in 4 functions i.e. COOL, Energy saver, Dehumid or an .
Timer on (See ig. # 5)
Unit must be on to set the timer. Unit will shut down automatically after it
accepts the settings in 5 seconds. Use this mode to pre-set the start time of
the unit 24 hours in advance.
a) Press TIMER ON, LED display will show "XX" (time set last time) when power
is connected first time, LED display will show "01".
b) Set desired number of hours by pressing the ( ) pad of the Temp/Time
buttons, one for each hour. If you passed the desired time use the ( ) pad
key to lower the selection.
c) After set TIMER ON, LED display will show the time. This time displayed:
unit will starts after X hours.
Timer off (See ig. # 5)
Unit must be running to set the timer off. Use this to preset the time you
would like the unit to shut off.
a) Press TIMER O , LED display will show "XX" (time set last time) when power
is connected first time, LED display will show "01".
b) Set desired number by pressing the ( ) pad of the Temp/Time buttons.
One for each hour. If you passed the desired time, use the ( ) pad key to
lower the selection.
c) After set TIMER O , LED display will show the room temperature about 5 seconds
later.
When using the timer the unit will use/revert to the last COOL and fan
settings when activated. The timer must be reset every time you choose to
use it.
TEMP/TIME
MODE SPEED TIMER
ON/OFF
Air ConditionerEdition:2005/12/28Air ConditionerEdition:2005/12/28Air ConditionerEdition:2005/12/28