Haier HWR08XC3 User manual

0010552275

1
English

2
English

3
1
1
2
4
4
5
5
6-7
8-14
8
8-14
15-19
16
16
17-19
20-21
21-22
23
English

4
English
Test power plug before each use:
1. Press ìreset ìbutton.
2 . Press ìtest ìbutton, unit should trip.
3. Press ìresetî button again for use .
Do not use if above test fail.
In the event this device trips , the cause of the malfunction is to
be corrected before further use of the device .
Important:

5
English

6
English
4-way airflow

7
English

8
English

9
English

10
It
English

11
English

12
English

13
English

14
English

15
English

16
English
Parts
Parts Supplied
ìCR2025ìbattery
curtain
attachment
screws 13/32"
window seal
gasket
curtain sash
screws
31/32"
Remote
control
basepan angle
left and right
side curtains

17
Installing Unit into A Window
Window Opening Requirements
The air conditioner is designed to fit into double or single hung sash type windows. Each of the
units comes with an installation kit that provides adjustable mounting louvers, to fill the gaps
between the sides of the unit, and the window frame. The chart below reflects the dimensions of
the units with, and without installation kits. Measure your window opening width and compare
it to the chart below to ensure that it meets the minimum and maximum window width requirements.
Model
A(inch)
Dimension
B(inch)
C(inch)
D(inch) Max
Case High
Case Width
D(inch) Min
Case Depth
HWR08XC5-T
Slide left-hand curtain assembly into
left ends of top and bottom rails.
Repeat for right-hand curtain
assembly. Fasten curtain retainer
strips to sides of outer case with six
ASSEMBLE
CURTAINS
Unpack unit on floor next to
installationlocation.
13/32" screws.
1
Caution: Never expose plastic front
or grille to extreme
temperatures.
English
13
16
201
4
5
8
A
B C
D

18
English
PREPARE
WINDOW FOR
INSTALLATION
Inspect window track, sash, and sill
for its ability to support the weight of
air conditioner.
Measure width between window
moldings to ensure Instant Mount
will fit window frame. Instant Mount
models are designed for windows
wide(the detail See Page 17) .
Instant Mount kit supplied with unit
is designed for mounting in most
double-hung windows without
storm windows. For installation in
window frame with storm window,
modify sill by adding wood strips
(not included) to inner and outer sills.
This raises unit and eliminates
interference of storm window frame.
2Mobile home window installation
Add wood strip (at least 1 1/2î wide)
along entire width of window sill.
Thickness of wood strip should match
height of front lip on window frame.
Fasten wood strip to sill with a
minimum of three countersunk wood
screws (not supplied with kit). This
provides a smooth surface for
mounting air conditioner.
Storm window installation
If storm window frame does not allow
adequate clearance below sill (1/2î
required), remove storm window
frame or create clearance by adding
a wood strip (at least 1 1/2î wide)
along entire width of sill. Fasten
wood strip to sill with at least three
countersunk wood screws (not
supplied with kit). This provides a
smooth surface for mounting air
conditioner.
3INSTALL UNIT IN
WINDOW
Place unit in window. Lower sash
until it rests behind front flange of top
rail. Bottom rail must rest behind
window sill.
INSTALL
BASEPAN ANGLE
Back front attachment screw out
several turns and slip Basepan Angle
over screw head. Snug screw with
angle resting on window ledge.
Install Two 31/32" screws through
angle into window ledge. Repeat for
opposite side.
4
SILL
Wood
Strip
1/2"
Minimum
O
U
T
D
O
O
R
Storm Window
Frame
1 1/2"
Minimum
I
N
D
O
O
R
1 1/2"
Minimum
Wood
Strip
I
N
D
O
O
R
O
U
T
D
O
O
R
Window
Frame
Must be a minimum
of 1/2" to clear
bottom rail on unit
Curtain assembly cut
away for clarity.
31/32"
screws Basepan
angle
Top rail
Bottom rail
About
5∞