Haier GDZ5.0-1 User manual

Exhaust Type Tumble Dryer
User's manual
Model: GDZ5.0-1
Please read this manual carefully before using.
Retain it for future reference.

Contents
Names Of The Parts......................................1
Important Safety Instructions........................2
Operation Cautions........................................4
Installation Instructions.............................5
.............................6
Using Method.................................................8
Dry Time Reference Table..... ....9
Care And Cleaning.......................................11
Trouble Shooting............................................12
Packing Notes And Electrical Safety Tips.......13
Specification............................the back cover
Wall Mounting Instructions
...........................

Names Of The Parts
Drum
Exhaust shroud
Air Intake shroud
Timer selector knob
Heat selector knob
Door
Power cord Exhaust vent
Back cover
Casing
Please check if the power receptacle has good earthing
Condition before using to guarantee your safety.
The manufacturer will not take responsibility for those
Risks occurred from not obeying this manual.
Door gasket
1
Window

2
9.Do not dry articles that have been previously cleaned in, washed in, socked
in, or spotted with gasoline, dry-cleaning solvents, or other flammable or
explosive substances, as they give off vapors that could ignite or explode.
Important Safety Instructions
Warning-To reduce the risk of fire ,electric shock, or injury to
persons when using your appliance, follow basic precautions,
including the following:
1.Read all instructions before using the appliance.
2.The tumble dryer is not to be used if chemicals have been used for cleaning.
3.The tumble dryer is intended only for drying textile material washed in water.
7.For appliances with ventilation openings in the base, that a carpet must not
obstruct the openings.
4.There has to be adequate ventilation to avoid the back flow of gases into the
room from appliances burning other fuels including open fires, when operating
the tumble dryer.
5.The lint trap is to be cleaned frequently.
6.Lint is not to be allowed to accumulate around the tumble dryer.
8.Exhaust air must not be discharged into a flue which is used for exhausting
fumes from appliances burning gas or other fuels.
11. Fabric softeners or similar products should not be used in a tumble dryer to
eliminate the effects of static electricity unless this practice is specifically
recommended by the manufacturer of the fabric softener or product.
12.Do not use heat to dry articles containing foam rubber or similarly textured
rubber-like materials.
10.Do not place items exposed to cooking oils in your dryer. Items contaminated
with cooking oils may contribute to a chemical reaction that could cause a
load to catch fire.
16.Do not use or place stove, gas device, water heater, tinder or similarities close to
your dryer. Do not install or store this appliance where it will be exposed to water
and/or to the weather.
15.Keep your dryer away from combustible materials (such as gasoline) during
operation to prevent the risk of fire.
13.Do not allow children to play on, climb on or in the appliance. Close supervision
of children is necessary when the appliance is used near children.
14.Before the appliance is removed from service or discarded, remove the door to
the drying compartment.

Important Safety Instructions
3
18.Do not repair or replace any part of the appliance or attempt any servicing unless
specifically recommended in the user-maintenance instructions or in published
user-repair instructions that you understand and have skills to carry out.
17.Do not tamper with controls.
20.If material has been used with any flammable liquids or solids it should not be
used in the dryer until all traces of the flammable liquids and its fumes have
been removed.
19.Keep area around the exhaust opening and adjacent surrounding areas free from
the accumulation of lint, dust and dirt.
22.Do not share a receptacle with other appliances. Do not use it when a plug
loosely inserted into a receptacle.
21.This dryer shall be connected to a three-wire, single phase, 230V AC
power receptacle more than 10A, which must be reliably grounded. A leakage
protector shall be used, if possible.
23.Do not excessively bend, stretch, twist, bind power cord or put heavy stuff on
it. Keep the terminator of power cord clean. Carefully clean it with dry cloth if
dusts accumulated. If damaged, power cord or plug must be replaced by our
service agent or qualified after-sale service person to avoid the risk of danger.
24.When normally using, the power cord of dryer shall be easily plugged or
unplugged by hand. It must be unplugged during power blackout, moving, not
in use or cleaning. Do not plug or unplug the power cord with wet hands.
25.Always disconnect dryer from electrical supply before attempting any service.
Disconnect power cord by grasping the plug, not the cord.
26.Do not block the exhaust vent when dryer operating to prevent it from
overheating or other dangers.
27.Do not let your dryer operate on packing foam. Otherwise it maybe cause fire
since heat accumulation or other external factors.
29.Do not place washed wet clothes in your dryer for a long time not drying them
(which may result in water leakage).
28.Only place sufficiently dehydrated clothes into your dryer for drying to prevent
leakage and longer drying time.
30.Don't touch the intake for the high temperature during the drying cycle.
31.Do not exceed dryer rated Max. Capacity.
32.The appliance must not be installed behind a lockable door, a sliding door
or a door with a hinge on the opposite side to that of the tumble dryer.

Clothes with zipper
Dry this kindof clothes withzipper
zipped or fastener
buckled and inside
out (to reducethe
impact noise between
metal and thedrum)
Clothes with ribbon or lace
should be dried in a nylon net
Put chemical fiber and/or clothes
with ribbon or lace
into a nylon net
before drying.
Do not load your dryer when
it is running.
Loading the dryer when it is running
shall be avoided
to prevent the
clothes over dried
or incompletely
dried.
Please flip clothes over manually
from time to time, if necessary,
when drying large ones.
It is not easy to flip over large clothes
(such as overcoat) in the drum, uneven
drying therefore happens sometimes.
If necessary, flip them over manually
from time to time to make them dried
completely.
Flip over clothes
Operation Cautions
Put rumpled clothes in order
Put all clothes in order after
dehydrated
before drying
them.
Remove the clothes out of your dryer
as early as possible
to reduce rumples.
Please hang the easily crumpled clothes
up with a hanger after dried
Anti-wrinkle method for clothes
crumpled easily
Decrease capacity to get good anti-
wrinkle result (the capacity shall be
4/5 of that of normal clothes).
Capacity reduced
•
Avoid to dry starched clothes in
your dryer to prevent link filter
from clogging, which may lead
to bad exhaust performance.
4

Soft items
Leg
Installation Instructions
For your safety and correct using your dryer, please observe all the instructions
in this manual toinstall and adjust your dryer.
Location of your dryer
Dryer should be located in a dry and well-vented place, not filled with moisture and
vapors and where rain cannot reach (like bathroom,open balcony and water faucet).
Do not locate your dryer in a place where sunlight directly shines.
Locate your dryer on horizontal solid ground, floor or a
special bracket to prevent vibration and noise. Keep a dista
nce of 10cm-15cm away from the rear wall when installing.
Do not use stove, gas etc. near your dryer to avoid dangers.
The dryer has air intake and exhaust cycles,which
needs good air-exhaust vent in the rear and well-vented
room. If used in a small space, air exchange fan or
exhaust duct can be installed at the vent to exhaust
hot wet air outdoors.
The length of exhaust duct shall not exceed 2m.
(10-15)cm
If the dryer is not used with bracket, take fixed
legs out of the accessory bag and screw them
into the assembly hole of the dryer to ensure
it be placed stable.
Install and use the fixed legs of your dryer
5

Wall Mounting Instructions
1. Determine the location of the dryer on the wall
and mark the bracket position.
* A minimum 50mm is needed between the top of
the dryer and the ceiling for ease of installation.
* If mounting above a washing machine, allow s
ufficient room to open the lid of the washer.
Drill & 3mm Bit
Wall Mounting Kit Includes
Wall Hanging Brackets
Hanging hook
2. Fix the wall hanging brackets(2 supplied) to the
wall securely (eg. into the stud.) Fit a timber slat
between the studs to mount the brackets onto
If the stud position is too wide. The distance
between each bracket is 155mm as per diagram.
6
Philips Head Screw
Driver
Expansile Screws,M5X
50mm
Helper to lift dryer
onto wall
Tools &parts
requir d
for Plaster/
wooden wall
e
Tools required
Tools required
Description
Plastic Spacers
Exhaust pipe

3. To install the hook to the dryer, remove
screws 1, 2, 3 & 4 as indicated in Fig. 2.
4. Align bracket as shown in Fig. 3 and fasten
screws tightly.
5. Remove lower side screws and install the
spacers provided as per Fig. 2.
6. Install exhaust duct: for upwards discharge, join
sections 1 and 3, for downwards discharge, join
sections 1, 2, 2 & 3 as per Fig. 4.
7. With assistance, mount dryer on wall brackets.
See Fig. 5.
Wall Mounting Instructions
7

8
Using Method
1. Plug the power cord
The appliance shall be supplied with230V,50Hz,
connected to a special receptacle more than
10A (reliably grounded).
2. Place the dehydrated clothes in your dryer
Check the following items before putting clothes in.
They shall be loaded in such a way that 2-3 pieces
each time and not in a group to avoid tangling, which
is not easy to turn it over resulting in uneven drying
since the clothes were wrapped.
Before drying your clothes
Make sure if clothes have any special requirements and suitable for drying.
Do not dry your clothes in your dryer if the materials of which cannot be dried
in a dryer or they bear the following labels:
Carefully check the clothes to be dried and remove combustible
material such as lighter and match as well as sharp metal items
like coin, hair clip and safety pin maybe mixed with the clothes
and in pockets.
Clothes with zipper or fastener shall be put into your dryer inside
out with zipper zipped and fastener buckled.
Do not tumble dry
Do not tumble dry
Hang to dry
Hang to dry
Drip dry
Drip dry
Dry flat
Dry flat
Dry in the shade
Dry in the shade
Please put clothes into the drum. Avoid clothes being
pressed by the door due to exposure out of the port,
which will cause clothes entangle and door gasket
release and consequently poor drying effect.
Separate dark and light colored items, like you do for washing.
Check for stains that may not have been removed in washing.
Dryer heat may permanently set some stains. Properly dried clothes
will need minimum of care when removed from dryer.
For optimum results,use dryer load of similar fabric, weight and construction. Place
small items in a mesh bag prevent from tangling.Do not overload the dryer. An
average load will fill up half the drum.

9
3. Control panel and its functions
Heat Selector Knob
Select Strong Dry for clothes particularly thick and in large
quantities or in lower room temperature.
Select Soft Dry for clothes not resistant to heat (like nylon
and chemical fibre ).
' '
' '
Strong
Soft
Select drying level according to the material, quantity and drying
requirements of the clothes to be dried as shown in the figure
Heat Selector Knob
Drying Timer Knob
Select dry program according to clothes materials and quantity, turn the timer knob to
relative position.
For down, sweater,
mohair, cotton sweater
and cotton-padded
clothes needing
freshening, tumbles
without heat. Also can
be individually used for
clothes long time in
closet with the
same results.
For clothes resistantto heat,
(Check the labelon the article
to be dried,to make sureit
can be safelytumble dried) ,
the heater isworking.
According to clothes
materials and quantity, turn
the timer knobto relative
position. Select 'Strong Dry'
for clothes particularlythick
and in largequantities.
Refer to
'Dry Time ReferenceTable'.
Motor keeps runningafter dryer time
heating finished whileheater stops
working and coldair into thedrum to
cool laundry.The whole coolingwill
be finished oncethe timer knobgets
to ‘OFF 'position.
Power off whenthe
timer knob in
'OFF' position.
The dryer starts
when turn theknob
clockwise.
Heating
Heating
Air drying
Air drying
Cooling
Cooling
OFF
OFF
Power off whenthe
timer knob in
'OFF' position.
The dryer starts
when turn theknob
clockwise.
OFF
OFF
OFF
20
20
40
60
80
80
120
120
100
100
140
140
160
160
180
180
200
200
20
20
40
40
60
60
0
220
220
0
OFF
OFF
Cooling
Cooling
DryTime Reference Table
Dry Capacity Approx.1kg Approx.2kg Approx.3.5kg Approx.5.0kg
Approx.200minApprox.160min
Approx.90minApprox.50min
Dry time affected by many factors, such as material, weight, thickness and the hydrated
ratio of clothes , the above listed dry time is only for reference.
Approx.90min Approx.150min
Soft
Strong
Dry time Suggest use strong''
Suggest use strong''

10
6. Do not take the laundry out until drying process is done
The last 20 minutes of hot air drying is cooling
to reduce the temperature of laundry inside
the drum.
To take the laundry out during drying, please
run cooling operation first since the temperature
inside the drum must be high.
Static electricity, due to friction, will be
generated on clothes made of chemical fibre
after dried. You can feel it when taking them out,
which is normal and shall not to be worried about.
7. Unplug the power cord
Please hold plug to unplug power cord from
a receptacle. Do not pull electrical wire directly
to prevent internal breakage or bad connection.
8. Clean filters
Clean the lint filter after every load and before each use. A clean filter ensures
sufficient drying. A layer of lint on the filter reduces airflow through the clothes
and prolongs drying time
5. Dry time settings
4. Set heat selector knob to select Strong
dry or Soft dry level.
' ' '
'' '
'Strong dry ' level for large quantity and low room temperature.
'Soft dry' for non heat-resistant clothes.
Soft
Heat selector knob
Select dry program according to clothes materials and
quantity, turn the timer knob to relative position. The
dryer starts running.
Strong
Caution: Dry timing knob cursor
shouldn't be set at the blank area,
as indicated in the right figure.
Do not
point the
cursor to
blank
Do not point the
cursor to blank.
Refer to the instructions on page 11.
OFF
OFF
20
40
60
80
120
100
140
140
160
180
180
200
200
20
40
60
0
220
0
OFF
Cooling
Cooling

11
The filter fixed in the
bottom of the drum
Do not wash directly with water.
Do not use thinner, gasolene or alcohol.
Do not use any type of spray cleaner when
cleaning the interior. Hazardous fumes or electric
shock could occur. If dryer drum becomes stained,
clean the drum with a damp cloth. Remove any
residue before drying the next load.
Clean cabinet with mild soap and water. Donot use
harsh or abrasive cleaners, this could damage the
dryer.
Clean the buildup such as lints on filters in time after each use, otherwise it will affect
the performance of your dryer.
Please unplug the power cord first when cleaning it.
1. Remove the filters
Remove by pulling straight up with hands inserted
into the four holes around the exhaust vent shroud
in the sequence of 'Exhaust vent shroud - Lint filter
- Exhaust filter', as shown in figure 1.
3. Install the filters
After cleaning, assemble in the sequence of 'exhaust filter
-filter-exhaust vent shroud',align the recesses in the center
of filter with the projection in the center of drum and make
sure that it is firmly inserted (as shown in figure 3).
2. Clean the lints
Separate 'exhaust vent shroud','lint filter'and 'exhaust
filter'and clean the lints on the filter and exhaust filter
with a soft brush or vacuum cleaner.
filters .
Do not damage the filters (as shown in figure 2)
Can also clean the
with water
The lint filter must be used for drying.
It must be cleaned in time befor and after each use.
Cleaning of filters
Figure 3
Care And Cleaning
Note: The filter fixed in the bottom of the drum shall also
be cleaned with a soft brush.
Lints
Exhaust
vent shroud
Dust Cleaner
Figure 2
Figure 1
Clean the interiordrum or dryer
housing, with wetsoft cloth, ifstained.
Lint
filter
Lint Filter
Exhaust
Filter
Exhaust Filter
DO NOT USE YOUR DRYER WITHOUT THE LINT FILTER.

12
(If your dryer exhibits problems, please unplug the power cord before checking) The following maybe
unrelated to a malfunction of the dryer itself, please reconfirm before calling a serviceman. If it does
relate to a malfunction, please contact our service agent or after-sales service and do not repair it
by yourself.
Trouble Shooting
Trouble Shooting
Problem Possible Cause What to do
Is the doorclosed?
Is the powercord inserted
firmly?
Does the receptaclehave
power?
Is the timerincorrectly
set up incold air?
Timer knob does not
turn
Drum does notturn
No hot airblown
out
Close the door.
Insert the powercord firmly
Check the power cord receptacle.
Set to hotair
Clean the filter.
Is the backfilter
clogged?
Dryer does not start
Is the timer in OFF position? Set dry time
Is power failure? Try again after power recovered
Is the power cord inserted
firmly?
Insert the power cord firmly
Have the clothes
been fully dehydrated?
Dehydrate the laundry
completely.
The laundry is not
throughly dried
(some of the clothes
still wet after dryer
stops) Reduce the laundryquantity.
Is the laundrytoo much?
Is the powercord inserted? Insert the powercord firmly.
Is the doorclosed? Close the door
Does the laundry twist? Loose the twisted laundry and
dry again.
Have any clothes dry easily and
hardly been dried together?
Dry the undried laundry again.
Have the dryer have been
added during operation?
Dry the undried laundry again.
Is the dryer placed in a small
and badly-vented space?
Place the dryer in a well-vented
place.

13
Packing Notes
User's Manual
Designation
One
Quantity
File packet
Location
Four
One
Legs of the dryer
Exhaust type tumble dryer
Accessory bag
Electrical Safety Tips
Please be careful when using your dryer since this product is class appliance.
1.Reliably grounded power supply must be used with the earth wire buried
underground. Do not connect with public utilities such as water pipe.
Separate earth wire from zero line and do not connect them together.
2. An individual special receptacle must be used, which shall be a product
have been qualified by national compulsive product certification.
For your and your family's safety, please improve as soon as possible if any
discrepancies with the above-mentioned requirements existed.
Wall mounting kit One

Specification
Model
Rated Input Power
Rated Fuse Current
Rated Max. Capacity
Overall Dimension
Net Weight
230V 50Hz
~
GDZ5.0-1
630mm 515mm 685mm
Extra 1070W Light 700W
10A
26.5kg
5.0kg
VC 532236 Parts Code:0030801264
the first edition
Rated Voltage Frequency