Haier GE CleanSpeak WE04X20528 Configuration guide

31-16703-2
Part Install Instructions
When replacing the control board, the dryer will not operate
until the replacement control board personality has been set.
GE CleanSpeak™ Dryer Control Board Personality Instructions
Once the control board has been replaced, follow all of the
steps below to properly set the personality. If The control
powers up with all of the user interface (UI) LEDs blinking,
only follow steps 5-8.
Step 1- Begin with the dryer in idle mode (No LED’s or display on).
Step 2- Simultaneously press and hold the Start pad (in some models press Start/Pause pad)
and rotate the cycle select knob 8 clicks clockwise or counter clockwise to enter Field Service
Mode.
Step 3- Upon entering the service mode, the Control will be in test selection mode and
display the test number according the knob position; the default test number is t1.
Rotating the knob counter clockwise will decrease the test number in the display. Rotating the
knob clockwise will increase the test number in the display.
Step 4- Rotate the knob counter clockwise or clockwise until the display shows td, then press
the [Start or Start/Pause] button to initiate the “Set Model” Procedure. All LED’s will begin
blinking.
Continued on reverse side….
!IMPORTANT SAFETY NOTICE
The information in this part instruction is intended for use by
individuals possessing adequate backgrounds of electrical,
electronic and mechanical experience. Any attempt to repair a
major appliance may result in personal injury and property
damage. The manufacturer or seller cannot be responsible for the
interpretation of this information, nor can it assume any liability in
connection with its use.
!WARNING
To avoid personal injury, disconnect power before servicing
this appliance. If electrical power is required for diagnosis or
test purposes, disconnect the power immediately after
performing the necessary checks. RECONNECT ALL
GROUNDING DEVICES If grounding wires, screws, straps,
clips, nuts, or washers used to complete a path to ground are
removed for service, they must be returned to their original
position and properly fastened.
WE04X20528, WE04X20527, WE4M544, WE04X20529,
WE04X25174, WE04X25175

Step 5- Simultaneously press and hold both the “Time” & “Level” buttons for three seconds to
prepare the Seven Segment Display for selecting the model..
Step 6- Press the “Time” button to increase or press the “Level” button to decrease the model
number selection until the correct model number is displayed.
Select 1 for model GTDP740EDWW
Select 2 for model GTDP740GDWW.
Select 3 for model GTDL740EDWW.
Select 4 for model GTDL740GDWW.
Select 5 for models GTDS810EDWS, GTDS815EDMC, GTDS820EDWS, GTDS825EDMC,
GHDS830EDWS and GHDS835EDMC.
Select 6 for models GTDS810GDWS, GTDS815GDMC, GTDS820GDWS, GTDS825GDMC,
GHDS830GDWS and GHDS835GDMC.
Select 7 for models GTDS850EDWS and GTDS855EDMC.
Select 8 for models GTDS850GDWS and GTDS855GDMC.
Select 9 for models GTD81ESPJMC and GTD81ESSJWS.
Select 10 for models GTD81GSPJMC and GTD81GSSJMC.
Select 13 for models GTD86ESPJMC and GTD86ESSJWS.
Select 14 for models GTD86GSPJMC and GTD86GSSJWS.
Step 7- When the proper personality is selected, press-hold [Start or Start/Pause] button for
three seconds to reset the micro. The board will then return to an idle state and will exit the
Service Mode.
Step 8- Test Dryer for proper operation.
Note: If an error is made in selecting the correct model number for the control, repeat steps
1-8.