Haier HAFRSJ64MC User manual

HAIER
HAFRSJ64MC
ENGLISH
Instruction Manual For Induction Hob
ITALIANO
Manuale di istruzioni per piano di cottura ad induzione
POLSKI
Instrukcja obsługi płyty indukcyjnej
FRANÇAIS
Manuel d’utilisation de la table de cuisson à induction
ESPAÑOL
Manual de instrucciones de la encimera de inducción
DEUTSCH
Bedienungsanleitung für Induktionskochfeld
Návod na obsluhu indukčnej varnej dosky SLOVENČINANávod k obsluze indukční varné desky ČEŠTINAManual de instruções para placa de indução PORTUGUÊSРъководство за употреба на индукционен плот БЪЛГАРСКИ

By placing CE mark on this product, we are confirming com-
pliance to all relevant European safety, health and environmental
requirements which are applicable in legisla�on for this product.
As applicable
EN-2
ENGLISH

EN-3

EN-4
ENGLISH
Haier
Haier

Haier
EN-5

1. Max. 2000/3000 W zone
2. Max. 2000/3000 W zone
3. Max. 1800/2300 W zone
4. Max. 1800/2300 W zone
5. Max. 3000/4000 W zone
6. Glass plate
7. Control panel
1. Heating zone power controls
2. "Cook with me Function control"
3. Timer control
4. Flexible Area control
6. ON/OFF control
Keylock.5
1
2
3
4
5
6
7
1
2
3
456
EN-6
ENGLISH

Touch Controls
•The controls respond to touch, so you don’t need to apply any pressure.
•Use the ball of your finger, not its tip.
•You will hear a beep each time a touch is registered.
•Make sure the controls are always clean, dry, and that there is no object (e.g. a utensil or a cloth) covering them.
Even a thin film of water may make the controls difficult to operate.
Choosing the right Cookware
• Only use cookware with a base suitable for induction cooking.
Lookfor the induction symbol on the packaging or on the bottom
of the pan.
• You can check whether yourcookware is suitable by carrying out a magnet test.
Move a magnettowards the base of the pan. If it is attracted,the pan is suitable
for induction.
• If you do not have a magnet:
1. Put some water in the pan you want tocheck.
2. If does notflash in the display and the water is heating, the pan is suitable.
• Cookware made from the following materials is not suitable: pure stainless steel, aluminium or copper
without a magnetic base, glass, wood, porcelain, ceramic, and earthenware.
Do not use cookware with jagged edges or a curved base.
Make sure that the base of your pan is smooth, sits flat against the glass, and is the same size as the cooking zone.
Use pans whose diameter is as large as the graphic of the zone selected. Using a pot a slightly wider energy will be
used at its maximum efficiency. If you use smaller pot efficiency could be less than expected. Pot less than 140 mm
could be undetected by the hob. Always centre your pan on the cooking zone.
Always lift pans off the Induction hob – do not slide, or they may scratch the glass.
EN-7

How to use
Start cooking
Touch the ON/OFF control for three seconds. After power on, the
buzzer beeps once, all displays show “–” or “– –”, indicating that the
induction hob has entered the state of standby mode.
Place a suitable pan on the cooking zone that you wish to use.
• Make sure the bottom of the pan and the surface of the cooking
zone are clean and dry.
Touching the heating zone slider control , and a indicator next to the
key will flash.
Select a heat setting by touching the slider control
• If you don’t choose a heat setting within 1 minute, the Induction
hob will automatically switch off. You will need to start again at step 1.
• You can modify the heat setting at any time during cooking.
If the display flashes alternately with the heat setting
This means that:
• you have not placed a pan on the correct cooking zone or,
• the pan you’re using is not suitable for induction cooking or,
• the pan is too small or not properly centered on the cooking zone.
EN-8
ENGLISH
No heating takes place unless there is a suitable pan on the cooking zone.
The฀display฀will฀automatically฀disappear฀after฀1฀minute฀if฀no฀suitable฀pan฀is฀placed฀on฀it.power up
power down

Finish cooking
Touching the heating zone selection control that you wish to
switch off.
the display shows “0”.
Turn the whole cooktop off by touching the ON/OFF control.
Beware of hot surfaces
H will show which cooking zone is hot to touch. It will
disappear when the surface has cooled down to a safe
temperature. It can also be used as an energy saving function
if you want to heat further pans, use the hotplate that is still
hot.
Using the Boost function
Activate the boost function
Touching the heating zone slider control
Touching the slider to “B”. Make sure the display shows “b”.
Cancel the Boost function
Touching the heating zone slider control that you wish to cancel
the boost function.
the display shows “0”.
Turn the cooking zone off by touching the slider to “ 0 ”. Make sure
Turn the cooking zone off by touching the slider to “0”. Make sure
EN-9

• The function can work in any cooking zone.
• The cooking zone returns to its original setting after 5 minutes.
• If the original heat setting equals 0, it will return to 9 after 5 minutes.
Flexible Area
• This area can be used as a single zone or as two different zones, accordingly to the cooking needs anytime.
• Flexible area is made of two independent inductors that can be controlled separately. When working as a single zone,
the part that is not covered by cookware is automatically switched off after one minute.
• To grant a correct pan detection and a even heat distribution, the cookware should be correctly placed:
- In the front or rear side of the flexible zone when the cookware is smaller than 22 cm
- Anywhere with bigger cookware
As big zone
To activate the flexible area as a single big zone, simply press the Flexible
Area control.
The power setting works as any other normal area.
If the pot is moved from the front to the rear part (or vice versa), the flexible area detects automatically the new position,
keeping the same power.
To add a further pot, press again the dedicated keys, in order to detect the cookware.
As two independent zones
To use the flexible area as two different zones with different power settings, press the Flexible Area control.
• This area can set the power according to the position of the pot.
• If the pot is on the bottom of flexible area, the power is set to Level 1.
• If the pot is on the top of flexible area, the power is set to Level 9.
for 2 second
Move the position of the pot, the power will change automatically
Press the Flexible Area control to turn off the cooking zone.
French Plaque
• If the pot is on the middle of flexible area, the power is set to Level 6.
French Plaque
To activate the French Plaque area, simply press the Flexible Area control
Cancel French Plaque
EN-10
ENGLISH

Locking the Controls
•
You can lock the controls to prevent unintended use (for example children accidentally turning the cooking zones
on).
•
When the controls are locked, all the controls except the ON/OFF control are disabled.
When the hob is in the lock mode, all the controls are disable except the ON/OFF , you can always turn the induction
hob off with the ON/OFF control in an emergency, but you shall unlock the hobfirst in the next operation.
Pause Mode
•You can pause the heating instead of shutting the hob off.
•When entering the Pause mode, all the controls except the ON/OFF control are disabled.
To enter pause mode
Short touch the Timer “ ” and Timer ” ” at the same
time.
All the indicator will show “ 11“
To exit pause mode
Short touch the Timer “ ” and Timer ” ” at the same time.
When the hob is in the pause mode, all the controls are disable except the ON/OFF , you can always turn the
induction hob off with the ON/OFF control in an emergency. The hob will shut down after 10min if you don’t exit the
pause mode.
Power Management Function
•
it is possible to set a maximum power absorption level for the induction hob, choosing up to different power
ranges.
•
induction hobs are able to limit themselves automatically in order to work at lower power level, to avoid the risk of
overloading.
The timer indicator will show “ Lo ”
To lock the controls
To unlock the controls
Touch and hold the lock control for a
while.
Touch and hold the lock control for a while.
EN-11

To enter Power Management Function
The timer indicator will show “ P5“ which means power
To switch to another level
or
There are 5 power levels, from “P1” to “p5”. The timer
indicator will show one of them.
“P1” : the maximum power is 2.5Kw.
“P2” : the maximum power is 3.5Kw.
“P3” : the maximum power is 4.5Kw.
“P4” : the maximum power is 5.5Kw.
Confirmation and Exit Power Management Function
” for confirmation.
Then the hob will be turned off.
Timer control
You can use the timer in two different ways:
•You can use it as a minute minder. In this case, the timer will not turn any cooking zone off when the set time is
up.
•
You can set it to turn one or more cooking zones off after the set time is up.
The timer of maximum is 99min.
Turn on the hob, then Press at the same time the
press +/- of the timer
and Timer ”
level 5 The default mode is on max power of the hob.
“P5” : the maximum power is max power of the hob.
Press at the same time key lock
key lock and ” .
Timer ”。EN-12
ENGLISH

a) Using the Timer as a Minute Minder
If you are not selecting any cooking zone
Make sure the cooktop is turned on.
Note: you can use the minute minder even if you’re not selecting any
cooking zone.
Touch “+” the controls of the timer. The minder
indicator will start flashing and “10” will show
in the timer display.
Set the time by touching the “-” or “+” control
of the timer
Hint: Touch the “-” or “+” control of the timer
once to decrease or increase by 1 minute.
Touch and hold the “-” or “+” control of the timer to decrease or
increase by 10 minutes.
When the time is set, it will begin to count down
immediately. The display will show the remaining
time and the timer indicator will flash for 5 seconds.
Buzzer will beep for 30 seconds and the timer
indicator shows “- - “ when the setting time finished.
b) Setting the timer to turn one or more cooking zones off
Set one zone
Touching the heating zone slider control
Set the time by touching the or control of the timer
Hint: Touch the “-“ or “+” control of the timer
once will decrease or increase by 1 minute.
Touch and hold the ”-“ or “+”control of the timer
will decrease or increase by 10 minutes.
When the time is set, it will begin to count down immediately. The display
will show the remaining time and the timer indicator flash for 5 seconds.
NOTE: The red dot next to power level indicator will illuminate
indicating that zone is selected.
EN-13

When cooking timer expires, the corresponding cooking zone will be
switched off automatically.
Other cooking zone will keep operating if they are turned on previously.
set more zones:
The steps for setting more zones are similar to the steps of setting one zone;
When you set the time for several cooking zones simultaneously, decimal dots of the relevant cooking zones are on.
The minute display shows the min. timer. The dot of the corresponding zone flashes.
The shown as below:
(set to 15 minutes)
(set to 45 minutes)
Once the countdown timer expires, the corresponding zone will
switch off. Then it will show the new min. timer and the dot of
corresponding zone will flash.
The shown as right:
(set to 30 minutes)
Touch the heating zone selection control, the corresponding timer will be shown in the timer indicator.
c) Cancel the timer
Touching the heating zone slider control that you want to cancel
the timer
Touch and hold the timer control “ - ”, the timer decreases to “00”
and the timer is cancelled.
Default working times
Auto shut down is a safety protection function for your induction hob. It shut down automatically if ever you forget to
turn off your cooking. The default working times for various power levels are shown in the below table:
Power level 1 2 3 4 5 6 7 8 9
Default working timer (hour) 8 8 8 4 4 4 2 2 2
When the pot is removed, the induction hob can stop heating immediately and the hob automatically switch off after 2
minutes.
People with a heart pace maker should consult with their doctor before using this unit.
EN-14
ENGLISH

To make the pairing between Hob and APP use the following process:
When wi-fi ON: one dot will appear on the right side of the LED
When WIFI OFF: No dot will appear.
Cook with me function
Press 4 seconds the "Cook with me" button on the hob. Once the 4 seconds have passed, the digit of the TIMER starts to blink with
PA written on it and starts the pairing process. Now follow the instructions from the App.
How to set Cook with me
If you want to get out of "Cook with me" function change the power
level of the zone.
First of all, you should download hOn App and install to your portable device. Then enroll your induction hob following the
instructions directly from the App.
Choose from the hOn App recipes menu or special programs menu.
Follow step by step the indications on the App and when you have
finished send the parameters to the hob that will cook for you.
When the hob receives the command from the app, the hob will beep
for 2 times and blink for one second to indicate that the instructions
have been received.
a. WIRELESS PARAMETERS
Technology Wi-Fi BLE NFC
Standard IEEE 802.11b/n/g Bluetooth v4.2, BR/EDR, BLE /
Frequency Band(s) [MHz] 2402-2480 2402-2480 /
Maximum Power [mW] 1500 1500 /
press 4 seconds
EN-15

EN-16
ENGLISH
Selection of cooking vessels
You may have a number of different cooking vessels
1. This induction hob can identify a variety of cooking vessels, which you can test by
one of the following methods:
Place the vessel on the cooking zone. If the corresponding cooking zone displays a
power level, then the vessel is suitable. If “U” flashes, then the vessel is not
suitable for use with the induction hob.
2. Hold a magnet to the vessel. If the magnet is attracted to the vessel is suitable for
use with the induction hob.
NB: The base of the vessel must contain magnetic material.
It must have flat bottom with a diameter according to the table 1 below.
3. Use only ferromagnetic cookwares made from enameled steel, cast iron or stainless
steel but compatible with induction
4. Use pans whose diameter of the ferromagnetic area (base of the pan) is in the range
of dimensions in the table below. (Table 1)
- If you use smaller pots, performance could be affected
- If you use pot with a diameter smaller than the one indicated in the table 1, pots
may not be detected
According to the dimension of the zone you can use pots of different diameters as picture
below:
Iron oil frying Stainless steel Iron pan Iron kettle Enamel
stainless steel
kettle
Enamel cooking
utesil
Iron plate

EN-17
5. If the ferromagnetic part covers only partially the base of the pan, only the
ferromagnetic area will heat up, the rest of the base may not heat up a sufficient
temperature for cooking.
6. If the ferromagnetic area is not homogeneous, but presents others material such as
aluminum this may affect the heating up and the pan detection.
If the base of the pan is similar to the pictures below the pan could be not detected.
The base diameter of induction cookware
Cooking zone
1 & 2 140
140
220
1803 & 4
Minimum Maximum
Flexi zone 220
The above may vary according to the size of the pan and the material it is made from.
220*400

The induction hob is equipped with a self diagnostic function. With this test the technician is able to check the function
of several components without disassembling or dismounting the hob from the working surface.
Troubleshooting
1) Failure code occur during customer using & Solution;
Failure code Problem Solution
Auto-Recovery
E1 Supply voltage is above the rated voltage. Please inspect whether power supply is normal.
Power on after the power supply is normal.
E2 Supply voltage is below the rated voltage.
E3 High temperature of ceramic plate sensor . 1# Wait for the temperature of ceramic plate return
to normal.
Touch “ON/OFF” button to restart unit.
E4 High temperature of ceramic plate sensor . 2#
E5 High temperature of IGBT . 1# Wait for the temperature of IGBT return to
normal.
Touch “ON/OFF” button to restart unit.
Check whether the fan runs smoothly;
if not , replace the fan.
E6 High temperature of IGBT. 2#
No Auto-Recovery
F3/F6 Ceramic plate temperature sensor failure- -short
circuit. (F3 for 1#,F6 for2#)
Check the connection or replace the ceramic
plate temperature sensor.
F4/F7 Ceramic plate temperature sensor failure--open
circuit. (F4 for 1#,F7 for2#)
F5/F8 Ceramic plate temperature sensor
failure—invalid . (F5 for 1#,F8 for2#)
F9/FA Temperature sensor of the IGBT failure. short
circuit/open circuit for 1# Replace the power board.
FC /FD Temperature sensor of the IGBT failure. short
circuit/open circuit for 2#
)
)
) )
) )
) )
)
))
EN-18
ENGLISH

The above are the judgment and inspection of common failures.
Please do not disassemble the unit by yourself to avoid any dangers and damages to the induction hob.
2) Specific Failure & Solution
Failure Problem Solution A Solution B
The LED does not
come on when unit is plugged
in.
No power supplied. Check to see if plug is
secured tightly in outlet and
that outlet is working.
The accessorial power
board and the display
board connected failure.
Check the connection.
The accessorial power
board is damaged.
Replace the accessorial
power board.
The display board is
damaged.
Replace the display board.
Some buttons can’t work, or
the LED display is not normal.
The display board is
damaged.
Replace the display board.
The Cooking Mode Indicator
comes on, but heating does
not start.
High temperature of the
hob.
Ambient temperature may be
too high. Air Intake or Air
Vent may be blocked.
There is something wrong
with the fan.
Check whether the fan runs
smoothly
if not , replace the fan.
The power board is
damaged.
Replace the power board.
Heating stops suddenly
during operation and the
display flashes “u”.
Pan Type is wrong. Use the proper pot (refer to
the instruction manual.)
Pan detection circuit
is damaged, replace
the power board.
Pot diameter is too small.
Cooker has overheated
;
Unit is overheated. Wait for
temperature to return to
normal.
Push “ON/OFF” button to
restart unit.
Heating zones of the same
side ( Such as the first and
the second zone ) would
display “u” .
The power board and the
display board connected
failure;
Check the connection.
The display board of
communicate part is
damaged.
Replace the display board.
The Main board is
damaged.
Replace the power board.
Fan motor sounds abnormal. The fan motor is damaged. Replace the fan.
EN-19