Haier 42EP24STV User manual

Please read thismanual carefully andcompletely
before operating the unit, andretain this manualfor
future reference.
PLASMA TV
OWNER`S MANUAL
MODELS: 42EP24STV

2 Plasma TV
THIS SYMBOL INDICATES THAT HIGH VOLTAGE IS PRESENT
INSIDE. IT IS DANGEROUS TO MAKE ANY KIND OF CONTACT
WITH ANY INSIDE PART OF THIS PRODUCT.
WARNING : To reduce the risk of electric shock do not remove cover or back.
No user-serviceable parts inside refer service to qualified service personnel.
RISK ELECTRIC SHOOK
DO NOT OPEN
WARNING
Safety of operators has been taken into consideration at the design and manufacture
phase, but inappropriate operation may cause electric shock or fire. To prevent the product
from being damaged, the following rules should be observed for the installation, use and
maintenance of th product. Read the following safety instruction before starting the operation.
The User Manual uses the following symbols to ensure a safe operation and prevent
any damage to operators or properties:
THIS SYMBOL INDICATES THAT THERE ARE IMPORTANT
OPERATING AND MAINTENANCE INSTRUCTIONS IN THE
LITERATURE ACCOMPANYING THE APPLIANCE.
FCC STATEMENT
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rule. These limits are designed to provide
reasonable protection against harmful interference in a residential installation.
This equipment generates, use and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However ,there is no guarantee that interference with not occur
in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encourage to try to correct the interference by one or more of the following
measures:
*Reorient or relocate the receiving antenna.
*Increase the separation between the equipment and receiver.
*Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
*Consult the dealer or an experienced radio/TV technician for help.
This device compiles with Part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) This device may be not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause undesired
operation.
FCC CAUTION:
To assure continued compliance and possible undesirable interference, the provided ferrite
cores must be used when connecting this plasma display to video equipment; and maintain
at least 40cm spacing to other peripheral device.
CANADIAN NOTICE:
This Class B digital apparatus compiles with Canadian ICES-003.

Owner s Manual 3
IMPORTANT SAFETY INSTRUCTIONS
Read all of the instructions before using this appliance. When using this
appliance, always exercise basic safety precautions, including the following:
1)Save these Instructions ---the safety and operating instructions should be
retained for future reference.
2)All warning on the appliance and in the operating instructions should be followed.
3)Cleaning --- Unplug from the wall outlet before cleaning. Do not use liquid
cleaners or aerosol cleaners. Use only dry cloth for cleaning.
4)Attachments ---do not use attachments not recommended by the manufacturer
as they may cause hazards.
5)Water and moisture -- do not place this product near water, for example, near a
bathtub, wash bowl, kitchen sink, laundry tub, in a wet basement, or near a
swimming pool.
6)Accessories ---do not place this unit on an unstable cart, stand, tripod, bracket,
or table. Use only with a cart, stand, tripod, bracket, or table recommend by the
manufacture, or sold with the unit.
7)Ventilation ---Slots and openings in the cabinets and the back or bottom are
provided for ventilation. These openings must not be blocked. In a built in
installation such a bookcase or rack do not install product unless proper ventilation
is provided.
8)Power Source ---this TV should be operated only from the type of power source
indicated on the rating label. If you are not sure of the type of power supply to your
home, consult your appliance dealer or local power company.
9)Do not defeat the safety purpose of the polarized or grounding-type plug. A
polarized plug has two blades with one wider than the other. Agrounding type plug
has two blades and a third grounding prong. The wide blade or the third prong are
provided for your safety. If the provided plug does not fit into your outlet, consult an
electrician for replacement of the obsolete outlet. To prevent electric shock, ensure
the grounding pin on the AC cord power plug is securely connected.
10)Power cord protection ---Power supply cords should be routed so that they are
not likely to be walked on or pinched by items placed upon or against them. Pay
particular attention to cords or plugs, convenience receptacle, and the point where
they exit from the appliance.
11)Lighting precaution ---for added protection for this product during a lighting
storm or when it is left unattended for long period of time, unplug it from the wall
outlet and disconnect the antenna or cable system. This will prevent damage to the
product due to lighting and power line surges.
12)Never push objects of any kind into this product through openings as they may
touch dangerous voltage point or short out parts that could result in a fire or electric
shock. Avoid spilling liquid of any kind on the product.
13)Servicing ---do not attempt to service the product by yourself, as opening or
removing covers may expose you to dangerous voltage or other hazards. Refer all
servicing to authorized service personnel.
14)Unplug this unit from the wall outlet and refer servicing to qualified service
personnel under the following conditions:
a. When the power supply cord or plug is damaged or frayed.

4 Plasma TV
SAVE THESE INSTRUCTIONS
Thank you for using our Haier product. This easy-to-use manual will guide you in
getting the best use of your product. Remember to record the model and serial
number. They are on label in back of the unit.
Model number
serial number
Date of purchase
b.If liquid has been spilled, or objects have been fallen into the unit.
c.If the unit has been exposed to rain or water.
d.If the unit does not operate normally by following the operating instructions.
Adjust only those controls that are covered by the operating instructions, as
improper adjustment of other controls may result in damage and will often
require extensive work by a qualified technician to restore the unit to its normal
operation.
e.If the unit has been dropped or damaged in any way.
f.When the unit exhibits a distinct change in performance; this indicates a need
for service.
15)Heat --- The product should be situated away heat source such as radiators, heat
registers, stoves, or other products (Including amplifiers) that product heat.
16)Overloading ---Do not overload wall outlets and extension cord as this can result
in a risk of fire or electric shock.

Owner s Manual 5
Warning..............................................................2
Safety Instructions............................................ 3-4
Introduction
Controls...........................................................6
Connection Options...........................................7
R ...........................8
Installing Batteries............................................8
Installation
Installation instructions....................................9
VCR Setup
................................... .......... 10
External A/VSource Setup...............................11
DVD Setup.....................................................11
DTV Setup
Monitor Out Setup...........................................12
PC Setup.......................................................13
Install the Speakers........................................14
Install the Stand.............................................15
Install the Standto the PDP............................. 15
Operation
Turning theTV On
Choose the MenuLanguage
Choose the InputSource
Basic Function
Operation Menu..........................................17
Sound Mode................................................17
Picture Mode...............................................17
Sleep Timer.................................................17
System Menu
Channel Type
CATV Type
Automatic Scan
Fine Tune
Color System ................................................19
Skip ..............................................................19
emote Control KeyFunctions
.......................................... .......... 10
Cable TV Setup
.....................................................12
Turning on the TV .......................................16
........................16
.............................16
................................................18
....................................................18
..............................................18
......................................................19
Prog. Switch.......................................................19
Picture Quality adjust
Picture QualityAdjust
Sound Adjustment
Sound Adjust
Adjustment Setup
Adjustment Setup...............................................22
Function Setup
Function Setup...................................................23
Menu Menu LanguageOption ..............................23
Menu Timeout Option.........................................23
Menu Background Option....................................23
Auto Off.............................................................23
BlueScreen .......................................................23
Close Caption....................................................24
Parental............................................................24
Time Setup............................................................25
Clock Setting ....................................................26
Off/On time .......................................................26
Rimind Time/RemindProg. .................................26
Lock Menu Options
Lock Setup........................................................27
Preset Prog. ....................................................27
Prog. Num .......................................................28
.........................................20
......................................................21
Calendar Display andCheck ...............................23
Change Password..............................................27
Tuning Lock.....................................................27
Source Lock.................................................... 28
Child Lock....................................................... 28
Max Volume.....................................................28
Unlock............................................................ 28
Screen Menu Options............................................. 28
AutoAdjustment ................................................29
Setting Picture Format.......................................29
Screen Position ................................................29
Troubleshooting Checklist......................................30
Maintenance......................................................... 31
Product Specifications........................................... 32
Setup and Operation Checklist
(See pages 10~15for available connectionand operational setupoptions.)
1. Unpack TV and all accessories.
2. Connect allexternal video andaudio equipment. Seepages 10 ~13.
3.Install the speakers and stand. seepages 14~16 .
4. Install batteriesin remote control.See page 8.
5. TurnTV on. See page 16
6. Turn video source equipmenton.

EXIT INPUT MENU
Signal source inputoption
Down/Up. Sel ct desired option on MENU or tune
to the desiredchannel.
e
VOLUME Buttons
MENU Button
Power On/Off Button
Remote Control Sensor
illuminates red instandby mode,illuminates blue when
the display isturned on
Power Standby Indicator
Menu exit
6 Plasma TV
VOL VOL
Front panel controls

AC-INPUT
DVI
VGA
L-AUDIO-R
AV IN
S-VIDEOVIDEO
L-AUDIO-R
AV OU T
VIDEO
AUDIO
DVI IN
AUDIO
VGA IN
COMPONENT IN
Pr/Cr Pb/Cb Y L-AUDIO-R
L
R
AUDIO OUT
SWITCH
VGA Input/Audio input
DVD/DTV Input
Connect a componentvideo/audio
device to thesejacks
DVI Input/Audio input
connect your cable/PC
through the input
Audio/Video Input
Connect audio/video
output from anexternal
device to thesejacks
S-Video Input
Power Cord Socket
This TV operateson AC power. Thevoltage is
indicated on thespecifications page. Never
attempt to operate the TV on DC power
Earphone port
0
Power On/Off
Owner s Manual 7
External audio/
video output
AUDIO output Antenna Input
Connect cable orantenna signals to
the TV, either directly or through your
cable box.
Real panel controls
ANT IN

When using theremote control. Aim it towards the remote sensor on the TV.
3
2
1
8 Plasma TV
Installing Batteries
Open the batterycompartment cover on the back side and install
the batteries matchingcorrect polarity (+ with +, - with -).
Install two 1.5VAA batteries. Don`t mix old or usedbatteries with
new ones.Replace cover.
Function introduction
INPUT
Ratates the sourceinput mode.
-
MTS/SAP EXIT
ARC
CALENDAR DNR
MUTE
INPUT
CH+
CC
MUTE
Switches the soundon or off
POWER
Turns your TV or any other programmed
equipment on oroff, depending on mode.
Digits
Program direct option(whenedit program,
every press canset different sign by turns among
the digits andsign on top of them)
Q.VIEW
Switch the currentchannel to the
last channel youhave viewed.
MENU
Brings up themain menu to the screen.
POWER
LOCK
GUIDE AVC
VOL-
Information display
Display of currentchannel
signals, program andsystems
EXIT
Clears all on-screendisplays and returns to
TV viewing fromany menu.
P.STD
Selects a factorypreset picture mode
depending on theviewing environment.
ARC
Changes the aspectratio.
FREEZE
Freezes the currently-viewedpicture.
GUIDE no available
Shows program schedule.
CC(Closed Caption)
CHANNEL UP/DOWN
Selects available channelsfound with
channel Scan.
MTS/SAP
Selects MTS sound:Mono, Stereo, and
SAP in Analog mode. Change the audio
Menu Language inDTV mode.
no available
S.STD
Selects the soundappropriate for
the program's character.
VOLUME UP/DOWN
Increases/decreases the soundlevel.
LOCK
.Press to enterthe Lock Set menu
AVC
Automatic Volume Control
FAVORITE
no available
MENU
Q.VIEW
CH-
VOL+
P.STD
S.STD RATING
DISPLAY
SLEEP
AUTO
PC FREEZE
DNR
Digital noise reduction
SLEEP
Press this keyto set sleeptimer.
CALENDAR
PC
Select PC source
AUTO
Auto adjust forPC
RATING
set the parentalcontrol.

VIDEO INPUT POWER
PC
AUTO DVI MUTE
EXIT
AVC
DISPLAY
DNR
MENU
/
LOCK CALENDAR
CC
RATING FREEZE
SURROUND
ARC
ENTER
SAVING
SLEEP
P.STD
S.STD
VOL+
VOL-
Speaker unit(X2)
(2.5MX2)
Connection cord
1 M4X12 x8Screws
4 Standx1 5 brace pole x2
2 M4X8 x2Screws 3 M5X16 x4Screws
6 PMMA baffle x1
Owner s Manual 9
GROUNDING
Ensure that youconnect the earthground wire toprevent possible electric
shock. If groundingmethods are not possible, have aqualified electrician
install a separatecircuit breaker.Do not tryto ground theunit by connecting
it to telephonewires, lightening rods,or gas pipes.
- The TV can be installed in various ways suchas on a wall, or on a desktop etc.
- The TV is designed to be mounted horizontally.
Ensure that thefollowing accessories are included with your plasma display. If anaccessory is missing, please contact the
dealer where youpurchased the product.
Short-circuit
Breaker
Power
Supply
Connecting block X4
ST4X16
Screw(x16)

10 Plasma TV
Do not leavea still picture from a VCR on the screen for a long If the 4:3format is used, the fixed imageson the
sides of thescreen may remain visible on the screen, if this format is used day after day. This is known as burn-in, it
is uneven wearof the screen area. Reduce contrast when displaying fixed images on the screen for along
- To avoid picture noise (interference), leavean adequate distance between the VCR and TV
Do not connectto both Video and
S-Video at the same In the
event that youconnect both Video
and the S-Video cables, onlythe
S-Video will work. So you should
not connect toS-Video if you want
to use Video.
1. Connect the audioand video cables from the
VCR's output jacksto the input jacks,
as shown inthe figure.
When connecting the to VCR, match
the jack colors(Video = yellow, Audio Left =white,
and AudioRight = red).
If you connectan S-VIDEO output from VCR to
the S-VIDEO input,the picture quality is
improved; compared toconnecting a regular
VCR to theVideo input.
2. Insert a videotape into the VCR and press
PLAY on the VCR. (Refer to theVCR owner`s
manual.)
3. Select theinput source by the INPUT button
on the remotecontrol.
TV
TV
- Aftersubscribing to a cable TV service from a local provider youcan watch cable TV programming. The cannot
display TV programming unless a TV tuner device or cableTV converter box is connected to the .
- For furtherinformation regarding cable TV service, contact your local cable TV service provider(s).
TV
TV
2. Connect theaudio and video cables from the Cable Box's output
jacks to theTV`s AV IN input jacks, as shown inthe figure.
When connecting theTV to a Cable Box, match the jack colors
(Video = yellow, Audio Left = white, and Audio Right =red).
(If you havea digital cable box please refer to page 12 , for DTV setup)
3. Select theinput source by using the INPUT button on the
remote control. (Ifconnected to AV IN, select AV1/S-VIDEO input source)
4. Select your desiredchannel with the remote control for cable box.
ANT IN
ANT IN
1. Connect theco-axial cable from antenna out of the cable box to
antenna in ofthe TV.
(Co-axial)

Owner s Manual 11
How to connect
Connect the audioand video cables from the external
equipment's output jacksto the TV`s AV IN input jacks, asshown in
the figure.
When connecting theTV to external equipment, match the
jack colors (Video = yellow, Audio Left = white, and Audio
Right = red).
How to use
1. Select the inputsource by using the INPUT button on
the remote control.
2. Operate thecorresponding external equipment. Refer to
external equipment operatingguide.
How to connect
1. Connect theDVD video outputs (Y, Pb, Pr) to the COMPONENT
(Y, Pb, Pr)IN jacks on the and connect theDVD
audio outputs tothe AUDIO INPUT jacks on the , as
shown in thefigure.
2. If your DVDonly has an S-Video output jack, connect thisto the
S-VIDEO input onthe and connect the DVD audio
outputs to theAUDIO INPUT jacks on the , as shown
in the figure.
NOTE:If your DVDplayer does not have component video output,
use S-Video .
How to use
1. Turnon the DVD player, insert a DVD.
2. Use theINPUT button on theremote control
to select YPbPr/YCbCr . (If connectedto S-VIDEO,
select theAV1/S-VIDEO external inputsource.)
3. Refer tothe DVD player's manual for operating instructions.
Component Input ports
Toget better picture quality, connect a DVDplayer to the component
input ports asshown below.
TV
TV
TV
TV
or composite(AV)
Video output ports
on DVD player
Component ports
on the TV

12 Plasma TV
- To watch digitally broadcast programs, purchase and connect a digital set-top box.
Digital Set-top Box
How to connect
Use the COMPONENT (Y, Pb, Pr)IN jacks, VGAor DVI INport for
video connections, dependingon your set-top box connections available.
Then, make thecorresponding audio connections.
How to use
1. Turnon the digital set-top box. (Refer to the owner`smanual for the digital
set-top box.)
2. Use INPUT on the remotecontrol to select YPbPr/YCbCr, VGA, or DVI source.
TV`s
Signal
480i
480p
720p
1080i
1080p
YPbPr/YCbCr
Yes
Yes
Yes
Yes
Yes
VGA
Yes
Yes
Yes
Yes
No
DVI
No
Yes
Yes
Yes
No
The has a special signal output capability which allows
you to hookup a second TV or TV.
Connect the secondTV or TV to the `s AV OUT.
See the OperatingManual of the second or TV for further
details regarding thatdevice`s input settings.
NOTE
YPbPr/YCbCr, VGA,DVI input sources cannot be used for monitor out.
TV
TV
TV

Owner s Manual 13
How to connect
1. To get thebest picture quality, adjust thePC
graphics card, ifnecessary.
2. Use the `s VGA IN or DVI(Digital Visual
Interface) IN portfor video connections, depending
on your PCconnector.
If the graphic card on the PC does notoutput
analog or digitalRGB simultaneously, connect
only one ofeither VGA IN or DVI IN to displaythe PC
on the .
If the graphic card on the PC does outputanalog
and digital RGBsimultaneously, set the display to
either VGAor DVI; (the other mode is set to Plug
and Play automaticallyby the display.)
3. Then, make the corresponding audio connection. If
using a soundcard, adjust the PC sound as required.
TV
TV
How to use
1. Turnon the PC and the
2. Turn on the display by pressing thePOWER button on the 's remote control.
3. Use INPUT on the remotecontrol to select VGA, or DVI source.
4. Check the image on your . There may be noiseassociated with the resolution, vertical pattern, contrast or
brightness in PCmode. If noise is present, change the PC modeto another resolution, change the refresh rate to anotherrate
or adjust thebrightness and contrast on MENU until the picture isclear. If the refresh rate of the PCgraphic card cannot
be changed, changethe PC graphic card or consult the manufacturer ofthe PC graphic card.
NOTES:
Use a DVI cable.
Avoid keeping a fixed image on the 's screen for a long period of The fixed image may become
permanently imprinted onthe screen. Use a screen saver when possible.
The synchronization inputform Horizontal and Vertical frequenciesare separate.
TV.
TV
TV
TV

1Face the PDP screen upside down on a clean blanket or a bracket and pay attention not to indent the
casing. Lay the two speaker aside of the PDP.
2. Fix 4 ST4X16 screws to the speaker. (position , , and in Figure )
3. Lean thespeaker against theplasma screen, ensuringthat the screwholes on theconnecting block in
line with thescrew holes onthe plasma screen, and hold the speaker. (position I, II, III and IV in Figure )
4. Fix the speaker to the plasma screen with ST4X16 screws.
5. Connect the speaker to the speaker terminal of plasma screen: Nip the speaker terminal and insert the
connecting cable intothe terminal slot.Release the speakerterminal and ensurethat the white
connecting cable is inserted in the terminal slot marked red and black connecting cable is inserted in the
black terminal slot, and that anode and cathode poles are correctly connected.
(See Figure )
Install the Speakers
14 Plasma TV
ST4X16 screw
RL
EXT SPEAKER
ST4X16 screw

Install the brace pole
M4X8rom the front.
1 After put thebrace pole to the stand,
use the screw8 M4x12 tofix it.
2 Takecare not to touch the stand and
the brace pole;
3 Fix the PMMAbaffle with the
screw 2
Install the PMMA Baffle
After installing thebrace pole(see figure below)
baffle
and put thebaffle into the stand.
rip the protectivesheet off of the PMMA
Install the Stand
Face the PDPscreen upside down on a cleanblanket or the bracket and pay attention not toindent the casing. (See figure)
Lay down thestand and put it to responding position of thePDP screen ,and make sure the brace pole towards the holeof the PDP .
Fix 2 PDPbrace pole tothe PDP on the back of the plasmadisplay with 4M5X16 screws.
Install the Stand to the PDP
Owner s Manual 15

16 Plasma TV
Turning on the TV just after installation.
1. Connect powercord correctly.
2. Press the SWITCHbutton on back of the TV. At thismoment, the TV is switched to standby mode.
Press the POWERbutton on the remote control or button on theTV and then the TV will turn on.
* In thismanual, the OSD (On Screen Display) may be differentfrom your `s, because it is just
an example tohelp you with the operation.
TV
TV
1.If the TV was turned off with the SWITCH button on the TV
Press the SWITCH button on the TV to turn the TV on.
2. If theTV was turned off with the remote control and then the ON/OFF switchon the back of the TV.
Press the SWITCHbutton on the back of TV and thenpress the POWER button on the remote control toturn
the TV on.
NOTE
If you intendto be away on vacation, disconnect the power plugfrom the wall power outlet.
TV
Turning on the TV
Choose the Menu Language
When you start using your set for the first time, you must select the Menu Language which will be used for displaying
menus and indications.
Menu Language English
OSD Timeout 15seconds
Menu Background Translucent
Calendar
Auto Off Off
BlueScreen Off
Close Caption Off
Parental
B
C
A
1Press MENU and then use VOL+/- button to select the
FUN. Menu.
2Press CH+/-button to selectMenu Language.
3Select a particular Menu Language by pressing VOL+/- button
repeatedly. You can choose one of three Menu Languages.
(English, French, Spanish)
4When you are satisfied with your choice, press the EXIT button to
return to normal viewing.
Choose the Input Source
- Change thepicture source sothat you can watch yourTV,cable TV, VCR, DVD, or any other devices that are
connected to yourTV.
1. Press INPUTbutton on the remote controller,the Scoure menu will appear on the screen.
2. Press CH+/-buttonfor option and then press VOL+/- button to confirm.
Note:
If AV1 and S-Video are inserted at the same time, priority willbe given to S-Video.
Source
TV
AV1/S-Video
YPbPr/YCbCr
VGA
DVI

Basic Function
Operation Menu
1.Press MENU buttonto open the main menu. Press VOL+/- button to select PIC., SOU.,ADJ., SYS. , FUN. or TIME menu.
2.Press CH+/- buttonto select submenu, and press VOL+/- button to increase/decrease the value or select the setup.
4.The setup timein display will disappear automatically when the latest preset time expiries. MENUdisplay time can
be set to5,10,15,20,25,30 and 40 seconds.
5.Press EXIT button to exit any menu if MENU is in display.
Sound Mode
Press S.STD buttonon the remote controller for menu display, and then useCH+/- button to select
the desired mode,press VOL+/- to confirm.
Basic Function
3.Press MENU toreturn to the main menu.
(This feature canalso be changed from the sound menu function screen)
Owner s Manual 17
SOU.Mode
Music
Standard
Theater
Personal
Picture Mode
Press P.STD button on the remote controller for menu display, and then use CH+/- button to select
the desired mode,press VOL+/- to confirm.
Sleep Timer
Every press ofSLEEP button, the timer will be set inthe following sequence:
Sleep 0Min Sleep 5Min Sleep 15Min Sleep 30Min Sleep 60Min Sleep 90Min Sleep 120Min Sleep 0Min
If remaining timeof set timer is to be displayed, press theSLEEP button once.
(This change canalso be made from Picture menu adjustment screen)
PIC.Mode
Vivid
Standard
Mild
Custom
Standard:
Vivid:
Mild:
Custom:
normal mode.
mode of watchingthe movement of picture.
the effect of the picture is soft.
picture effect which you favorite.
Normal sound withmoderate bass and treble setting.
.
Enables extra bassand treble to enhance the movie experience.
Personal:
Standard:
Music:
Theater:
A sparesetting that can be adjusted to personal tastes.
Adjust the soundto best suit music programs

This TV set has three methods to set channels, which are respectively Automatic search, manual search fine tune.
In this section,how to usethe remote control to set channel is explained. You can also use
buttons on the TV set to set channel.
System Menu
Color Sys. AUTO
Sound Sys. M/N
Fine Tune 49.75MHz
Skip Off
Channel Type Cable
CATV Type STD
Auto Scan
Prog. Switch
B
C
A
1Press MENU button and then use VOL+/- button to select the SYS. Menu.
2Press CH+/- buttons to select "Channel Type" item.
3Press VOL+ buttonto select Cable or Air item.
Note : the tuning menu will be
only operated in normal TV mode.
Channel Type
B
C
A
18 Plasma TV
Automatic Scan
1Press MENU button and then use VOL+/- button to select the SYS. Menu.
2Press CH+/- buttons to select "Auto Scan" item.
3Press VOL+ button to ensure automatic search function work.
4Press MENU button to stop automatic search function.
After the search has finished, all channels now playing
program will be automatically preset in order.
When Air is selected, theTV will detect antenna signals and will search
for antenna TV(NTSC and ATSC) channels available in your local area.
When Cable is selected, theTV will detect cable company supplied
signals and willsearch for cable TV (NTSC,ATSC, QAM modulated)
channels available inyour area.
Make sure thatregistration with your cable TV provider and connection
of equipment arecompleted.
When Air and Cable are selected, theTV will detect the antenna
signals and cablecompany supplied signals, and search for the
antenna TV andcable TV channels available in your area.
Color Sys. AUTO
Sound Sys. M/N
Fine Tune 49.75MHz
Skip Off
Channel Type Cable
CATV Type STD
Auto Scan
Prog. Switch
CATV Type
1Press MENU button and then use VOL+/- button to select the SYS. Menu.
2Press CH+/- buttons to select "CATV Type" item.
3Press VOL+ buttonto select STD,IRC or HRC item.
Before your television can begin memorizing the available channels, you must specify the
type of signal source that is connected tothe TV (i.e., an antenna or a cable system).
Note: STD, HRCand IRC identify various types of cable TV systems.
Contact your localcable company to identify the type of cable system
that exists inyour particular area.

Color System
B
C
A
Usually this shouldbe set in the auto position. However if thecolor displayed
on the screenare incorrect, you can manually select the correct color system.
Press MENU andthen VOL+/- button, till the picturemenu shown on the
right will displayon the screen.
Press CH+/- buttons to select "Color Sys.", then pressthe VOL-/+ buttons
to select thecorrect color system. In general, you can set itas "AUTO".
After the programsare presetting, you can skip some programs so thatto select your favorite channels only.
1. Press CH+/-button or Direct-digit choosing button to select a channeldirectly.
2.Press MENU and then use VOL+/- button to selectthe SYS. Menu.
3.Press CH+/-buttons to select "Skip" item.
4. press VOL-/+ button to setSkip as On.
5. When youare satisfied with your choice, press MENU button to returnto
the previous menuor press EXIT button to returnto TV viewing.
1. Use Direct-digitChoosing button to select the number of the channel to
be recovered.
2. Do theabove steps again.
3. Press VOL+/-button to set Skip as Off.
Skip
B
C
A
If you want to recover the skipped channel
1..Press MENU and then use VOL+/- button to selectthe SYS. Menu
2. Press CH-/+button to select Prog.Switch.
3. Press VOL+ toenter the submenu, and press the digital button toset the desired
channel number,
Press CH+ buttonto To Prog item, and Press the digital button to set theexchange
channel number,press CH+ button to Switch, then press VOL+ buttonto confirm.
4. When youare satisfied with your choice, pressMENU button to return to
the previous menuor press EXIT button to return to TV viewing.
Prog.Switch
Current Prog 000
ToProg 001
Switch
B
C
A
System Menu
Owner s Manual 19
Color Sys. AUTO
Sound Sys. M/N
Fine Tune 49.75MHz
Skip Off
Channel Type Cable
CATV Type STD
Auto Scan
Prog. Switch
Color Sys. AUTO
Sound Sys. M/N
Fine Tune 49.75MHz
Skip Off
Channel Type Cable
CATV Type STD
Auto Scan
Prog. Switch
Fine Tune
B
C
A
If the picture and/or sound are poor, try using the fine tune feature.
Do not use this feature unless reception is poor.
1Repeat step 1-2, then press CH+/- buttons to select "Fine Tune" item.
2Press VOL-/+ buttons repeatedly to carry out fine tune, till the best
picture and sound are obtained, then loosen the button.
Color Sys. AUTO
Sound Sys. M/N
Fine Tune 49.75MHz
Skip Off
Channel Type Cable
CATV Type STD
Auto Scan
Prog. Switch

Picture Quality Adjust
Picture Quality Adjust
Picture Quality Adjust
The TV menu gives you an overview of MENU you can select.
Note: Depending on the input signal, one or more menu items may not be selectable.
Contrast
This will adjustthe intensity of bright parts in the picture butkeep
the dark partsunchanged.
Brightness
This will adjustthe light output of the complete picture, which will
mainly affect the darker areas of the picture.
Color
This will adjustthe saturation level of the colors to suit yourpersonal preference.
Hue (selectable in NTSCmode only)
Allows you toselect the color mix (Hue) of the picture.
Sharpness
This will adjustthe sharpness of fine details in the picture.
DNR (Digital NoiseReduction )
Automatically filters outand reduces the image noise and improves picture
quality when receivingweak video signals.
Select Auto/Off/Weak/Medium /Strong according to the image noise.
1Press MENU and then use VOL+/- button to selectthe PIC. Menu.
2Press CH+/-button to selectthe desired items.
3Press VOL+/- button to adjust the setting.
4When you aresatisfied with your choice, press MENU button to returnto
the previous menuor press EXIT button to returnto TV viewing.
Mode Custom
Contrast
Brightness
Color
Hue
Sharpness
DNR Auto
B
C
A
50
50
50
0
50
Note:
When Custom mode is not selected, the Custom mode can be entered automatically if Contrast, Brightness,
Color, Hueand Sharpness parameters are adjusted.
20 Plasma TV