Haier HWM65-728 User manual

User’s Manual
Fully Automatic Washing Machine
This manual is for
HWM60-728
HWM65-728
Please read this manual carefully before using.z
Retain it for future reference.z
Index
Safety precautionsy...............2
Packing listy...........................4
Names of the partsy...............4
Installation andy
adjustment............................5
Preparation beforey
washing ................................9
Usetheoperationbuttonsy....11
13
15
16
0030808120
Disposal after washingy.......
Trouble-shooting Answery
to question..........................
SpecL¿cationy.......................

2
Safety precautions
Contents marked with that symbol are actions forbidden to
perform. Performing of those actions may result in damage
ofthemachineorinjurethepersonalsafetyoftheuser.
Forbidden sign
Contents marked with that symbol are related to the safety
of the product and the personal safety of the users. Please
operate in strict conformity to the contents, otherwise it may
causedamageofthemachineorinjurethepersonalsafety
of the user.
Warning sign
Meaning and description of the symbols
Please check if the power receptacle has good earthing condition before using to guaranteez
your safety.
Pleasecheckifthewaterfaucetisopen,andiftheconnectionofthewaterinletpipeisz
proper.
Itissuggestedtousefoamlesswashingpowder.z
Pleasedon’tusethewasherintheenvironmentbelow0°C;ifthewasherhasbeenstoredz
below0°C,pleasebesuretoensurethewasherisplacedundertheroomtemperature
for 2~4 hours and then use otherwise the washing effects may be lowered or the
washer may be damaged.
Pleaseinsertthepowercordintospecialreceptaclewithratedvoltage.z
Be sure to use single-phase three pins receptacle.The earthing terminal of
the receptacle must be earthed reliably. If possible,please adopt electric
leakage protector.
Thewashingmachinemustbepositionedsothattheplugisaccessible.Bez
suretopulltheplugoffandclosethewaterfaucetinfollowingcases:power
failure, delivering the machine, setting the machine idle or cleaning the
machine.
Donotplugorpullthepowerplugwithwethand.z
Do not bend ,extend, twist, bind or alter the power cord by force. Do not press
ornipitwithweight.
z
Keep the pin of the power plug clean, if the power plug is polluted with dust,z
please wipe with dry cloth carefully.
Ifthesupplycordisdamaged,itmustbereplacedbythemanufactureroritsz
service agent or a similarly qualL¿ed person in order to avoid a hazard.
Do not let the machine share one receptacle with otherz
electric appliances. If the plugging into the receptacles
loose, do not use the plug any more.

3
In case the washing machine is installed on groundz
with carpet, do not block the ventilation hole
with carpet.
Do not put the machine at damp place like thez
bathroom. Never wash it with water. Do not put wet
laundries on the control panel.
Do not wash water-proof laundries like the raincoat,z
bikecoversetc.toavoidabnormalvibrations
in spinning. Wash the clothes that can Àoat
onthewatersurfaceeasily,pleasebecareful
especially,for fear damage.
Donotstretchhandsintotheworkingmachine.Itisz
dangerous even if the rotation is slow. Take special
care of the children.
Donotputanyhotorheavyitems(suchasthez
kettle with hot water ) on the washing machine.
Do not wash laundries with volatile materials (suchz
as thinner, petrol etc.)
Thechildrenshallnotapproachtheworkingz
washing machine.
Keep the machine away from direct sunlight andz
heat source like the heater.
Do not decompose, repair or alter the machine byz
yourself.
Donotusewaterhotterthan50°C.z

4
Names of the parts
Packing list
Fully automatic
washing machine
Water inlet hose Bottom plate Tapping screws
(One Package)
User’s manual
Warranty card
AllillustrationsinthisManualarez
givenforreferenceonly.Your
products and accessories may
showdifferencesfromthese
illustrationsduetoourcontinuous
improvement.
Control panel seat
Top lid component
Back cover
Power line
Drain hose
Cabinet handle
Water inlet valve
Jacket of drain hose
Water absorption cushion
Drain outlet protecting cover
Hanging hole
Filter cover(2 pieces)
Control panel film
Cabinet
Adjustable foot
Adjustable foot film
Screw cover(right)
Back control board
Screw cover(left)
Outer tub cover
Lint filter(2 pieces)
Balance ring
Inner tub Liquid whitener inlet
Fixed foot(3 pieces)
Detergent box
Pulsator
The model HWM60-728have not
the detergent box and the back
control board in the control panel
seat,and its two lint filters can also
be used as detergent boxes.
z

5
Installation and adjustment
Please install and adjust the machine according to the requirement of the manual. It is very important
to your security and correct operating the machine.
After opening the package, please lean the washing machine gently down on soft items
(liketowelcloth,blanket,etc.).Installthebottomplatetothebottomofthemachinewith
screws by a cross screwdriver, then lift the machine up gently. See to the ¿gure: (Please
¿rstpulloffthepowerplugfromthereceptaclebeforeinstalling.)
Adjust the adjustable foot:z
To twist the adjustable foot, please ¿rstliftupthesideofthelegslightly,loosenthe
adjustable nut, and twist the foot. Please make sure to keep the washing machine
in balance.
1.
After adjustment, fasten the nut.
The adjustable foot
2.
Thewashingmachineawayfromwallshouldbeoverrun20mm.Thelargestallowableslope
of the shank base of the machine is 2°. The slanting or rough ground will result in unstable
runningorstoppageofthemachine.Pleaseadjustitwithfollowingmethods:
Carpet
Back
Front
Bottom plate
Screw
Confirm it's horizontal:
Hang the lead line to check if it is horizontal.
z

6
Screw knife
Figure 4
Figure 5
About 4mm before twisting
About less than 2mm after twisting
Screw
Bushing
Sign plate
Screw nut
Figure 2 Figure 3
Figure 6
2.Loosen the screw till the water faucet can be
accessed. Put the jointer of the water inlet
hose on the faucet. See to Figure 2. (If the
faucet is too large and the jointer can not be
set on the water faucet,please loosen the four
screws and take out the bushing in the jointer.
The front end of the faucet must be smooth,
otherwise it may leak water .See to Figure 3.)
3.Fasten the four screws evenly. See to Figure 4.
4.Take off the nameplate. Twist the fastening nut
as per the indication of the figure to seal up the
exit end face of the faucet. See to Figure 5.
Remark: Before installation, the threading is
4mm above the upper surface of the nut.After
installation, the threading is 2mm above the
upper surface of the nut.See to Figure 6.
Connection between the water inlet hose jointer and the
water faucet
1.Press the lower end of the lock lever and push
down the slider. Take off the water inlet hose
jointer from the water inlet hose component.
See to Figure 1.
water inlet hose jointer
water inlet hose
Figure 1
Slider
Lock lever
The exit end face of the faucet
water faucet, suitable
It is required that the front end shall be longer than 10mm.
The exit end face of the faucet shall be flat and smooth.If not please file it to avoid leakage.
Confirm the water faucet
z
z
water faucet, not suitable

1.Do not take off the water absorption cushion. Please
check if the cushion is dropped or damaged before
each usage. If it happens please contact our
after-sale department immediately.
2.Put the nut of the water inlet hose on the valve
jointer.
3.Fasten the nut. Swing it gently to confirm if it's
suitable.
1.Push down the slider. Insert the water inlet hose
into the jointer.
2.Hang the lock lever to the jointer. Release the
slider till a click sound is heard.
1.Swing the hose gently to confirm if it is fastened stable.
2.After installation, open the faucet to check if it leaks.
3.Do not bend the hose with overstrain.
4.Before each usage please check if the connection between
the jointer of the water inlet hose and the water faucet, and
the installation of the water inlet hose are firm, so as to
prevent dropping from improper installation position.
1.Close the water faucet.
2. Press the locking lever. Push down the slider.Then pull off the water inlet hose.
If the machine is used frequently, the jointer of the water inlet hose can be kept
on the faucet to prevent damaging the fixing screw.
Dismantle the water inlet hose
Connection between the jointer of the water inlet hose and the
water inlet hose
Check the connection between the jointer of the water inlet hose
and the water faucet
Locking lever
Slider
water absorption
cushion
nut of the water
inlet hose
The jointer of the
water inlet hose
Slider
Locking lever
jointer of the
water inlet valve
Connection between the water inlet hose and the washer
7

8
The drain hose shall drain smoothly.
Do not trample or press the drain hose.2Theheightofthedrainhoseshallbeless
than10cm,orthedrainagewillnotbesmooth,
and cost such long time that the machine may
stop at mid way.
1
3
5
4
If the drain hose is too long, cut it at mid
point. To make smooth drainage,cut the front
end of the hose slantingly.
If the extra hose is too long,cut it either at A or at Bpoint.
If extra drain hose is needed,please
make separate purchase.The inner
diameter of the extra hose shall not
less than 30mm, and the length shall
not exceed 1.5m.
Remark:In order to make sure of the correct of installation, it is suggested to change the
direction of the drain hose with our company serviceman.
Drain outlet
protecting cover
Drain hose
bushing
Figure 1
Figure 3
Drain hose
frame
Drain hose
bushing
Figure 2
Drain hose
frame
Drain outlet
protecting cover
Drain hose
Figure 4
1.Dismantle the back cover of the washing machine.
2.Take off the drain hose frame. Put down the drain
hose , put the drain hose into the cabinet, take off
the drain hose bushing(As indicated in Figure 1).
3.Dismantle the protecting cover of the drain outlet
at the other side.Install the drain hose bushing
(As Indicated in Figure 2).
4.Extend the drain hose from the other side. Fixthe
drain hose with the drain hose frame(As
indicated in Figure 3).
5.Install the protecting cover of the drain outlet at
the other side (As indicated in Figure 4).
How to change the direction of the drain hose

9
Preparation before washing
Connect the water inlet hose. Open the water faucet.z
Con¿rmthatthewashingmachineisearthedreliably.Theninsert
thepowerplugintothereceptacle.Theearthterminalshallnot
link to gas pipeline and faucet water pipeline.
z
Put down the drain hose.z
Slanting or uneven ground may result in unstable working or
abnormal noise. Please make the machine stand horizontally.
z
Clear the pocket. Take out the coins,sand, hairpins etc.
Confirm if there is special requirement for the laundries.
Checkifthelaundriesareapplicableforwashingwithmachine.z
Pleaserepairthedamagedclothbeforewashinginordertoavoidthesituationworse.z
Dividethelaundriesthatarenotcolorfastfromotherlaundries.z
Put those laundries dif¿cult to absorb water into water with hand.z
For those laundries with heavy soil, please ¿rst remove the dirt like mud or dust. For the parts
with heavy soil, please apply detergent on them in advance, which can make it easier to remove
the soil.
z
Forthoselaundriesthatmaygetlintballandthosewithlongfur,turnitoverbeforeputtingin.z
Donotputthoselaundriespollutedbychemicalsintothewashingmachinedirectly.z
Theforeignmaterialswillresultindamageofthemachine.z
The quantity of the laundries shall not be too large. Stretch and loosen the
laundries before putting them in the tub.
Whenthepulsatorisrunning,thebuttonsofthelaundriesmaycausenoise.
For the sake of discretion, please put the laundries with buttons into other
laundries.
Tie the long strips; fasten the buttons;close zippers.
Pay attention to followings before washing the laundries

10
Howtousethewhitener
Howtousethewashingpowder
How to use the softener(only applicable for HWM65-728)
Fill water to decided level. Dilute the whitener with
container. Pour it slowly into the washing tub.
z
Avoid using whitener on laundries with color or
patternastheyarepronetolosecolor.
z
The whitener shall not touch the laundries directly.z
Refertotheuser’smanualfortheusageand
quantity of the whitener.
z
Forpowderwhitener,pleasedissolveitbeforeusing.z
Directlydissolvedinthemachine:(notapplicableforfuzzyprogram)z
.retawfoytitnauqllamslliF.1
.yletelpmoctievlossidotsdnoces03rofnuR.redwopehtddA.2
.level
retawelbatiustceleS.seirdnualehtnituP.3
Theinstantdissolvingofthewashingpowder:z
.reniatnocadnaC°03foretawmraweraperP.1
.tievlossidyllufotgnirritselihwredwopehtddA.2
If you select the quick program, it is suggested to adopt
liquid detergent instead of washing powder to guarantee
the washing effect.
z
Put in the proper quantities detergent according to the
water level and the laundries quantities.
z
It is suggested not to use high sudsing detergent. Washing
powderwithpoorqualityorlongtimestoragemaybecaked.
Please pay attention to cleaning the detergent box in time.
z
Theusageanddoseofthesoftenerasperthespeci¿cations of softener.z
Turn the inner tub,you will find a softener inlet as the figure 1,open the
cover,put the softener into the inlet as the figure 2.Before washing,close
the cover and the softener will drop into the inner tub during the last time
rinsing.
z
After the softener is put in,please don’t place for a long time otherwise
softener may solidify and cause flowing not smooth.
z
Thecapacityofwashingandspinningofthemachinerefertothelargestweightz
ofthestandardlaundriesunderdryconditionthatcanbewashedorspinnedinone
time. One time washing quantity shall be lower than the rated capacity.
The thickness, size, type of the cloth will inÀuence the actual washing capacity. Itz
is suitable for one time washing to put in reasonable amount of laundries and the
laundries can be turned round in washing.
Donotselecthighwaterlevelforlaundrieslessthan1.0kg,soastoavoidz
splashing of water.
Figure 1
Figure 2
Open Close
Access for
detergent
Access for detergent
Access for softener
Control panel seat
Liquid whitener inlet
Washing powder box
(Lint filter)
Washing powder box
Figure 1˄HWM60-728)
Figure 2(HWM65-728)
(HWM65-728) (HWM60-728)

11
Use the operation buttons
Off
On: indicate the program about to run,or indicate
theselectedmodeorindicatethewaterlevel
Flashing: indicate the running program
During sensing, it displays “--” .
During delay procedure, it displays the
remained delay time (in hours).
During operation of programs,it displays the
remaining time (in minutes).
In case of abnormal phenomenon, it displays
the abnormal symbols (see to Page 15).
Program Applicable situation
STANDARD
HEAVY
Washing the normal laundries
Washing the bigger and heavier laundries
GENTLE Washing the woollen textiles or underwear
QUICK Washing the laundries with small quantity
and light soil
Washing the blanket
Washing the cotton textiles
Washing the woollen textiles
BLANKET
COTTON
WOOL
TUB DRY Drying the inner tub and the outer tub,
which can avoid growing mildew
Afterthepowerisswitchedon,pressittostart
the machine.
During working, push it to pause.
Duringpause,pushthisbuttontorestart
andgoonworking
Push the “POWER ON/OFF” button to
switch on the power.
Whenthepowerison,pushitagainto
switch off the power.
Push the “POWER ON/OFF” button to
switch on the power.If the “START/PAUSE”
button is not pushed, the washing machine
will automatically switch off the power
after 5 minutes.
Thedigitrondisplaysthetimeremained
You can choose one or more process
among soak,wash,rinse,spin.
The button is invalid if you choose
“QUICK” or “TUB DRY” program.
You can not choose soak process if
you choose “WOOL” program.
(inminutes)beforethewashingis¿nished.
Push “DELAY” button, the digitron displays
the delay time of washing (in hours). The
indicator flashes to indicate that the delay
function is operating.
Push “DELAY” button to display the delay
mode.
During the standard program,the washing
machine can detect the laundries automatically.
After detection,it will set the water level to
suitable value automatically among the water
level “LOW”,”MEDIUM”,“HIGH” and ”MAXIMUM”.
You can also set water level by yourself.After the
machineisstarted,itwillnotsetwaterlevel
automatically. You shall push the “START/PAUSE”
button to make new setting.
If there’s water inside the tub, the machine can
notdetectthelaundriesandwilldisplaywater
level “MEDIUM” .If wet laundries are put in, it
may display water level “MAXIMUM”.You must
setsuitablewaterlevelbyyourself.
If QUICK program is selected, it will display water
level “LOW”,the water level can not be adjusted.
If TUB DRY program is selected, the water level
will not respond.
During operation of wash , rinse and soak
program,youcanpushdownthewaterlevel
buttontoaddwater.Whenyoureleasethe
button,oritreachestheoverÀow water level,
the machine will stop adding water.
The water level decided may be different from
actual value because of the different moisture
level of the laundries.
RESERVE(HOURS)
REMAIN(MINUTES)
WASH
SOAK
RINSE
SPIN
GENTLE
QUICK
HEAVY
BLANKET
COTTEN
WOOL
TUB DRY
POWER
ON/OFF
START/PAUSE
WATER LEVEL
PROGRAM
PROCESS
DELAY
MAXIMUM
HIGH
MEDIUM
LOW
EXTRA LOW
STANDARD

12
Push the “ ” button to switch on the power
Push the “ ” button to select suitable procedure
Push the “ ” button to select suitable automatic program
After the power is switched on, the machine will set the “STANDARD” program
automatically.To select other automatic program, push the “PROGRAM” button
till the relative indicator is light. Refer to the “PROGRAM” button on Page 11 for
the selection. For instance: select “QUICK” program for laundries with small quantity
and light soil.
In selecting the “STANDARD” program, the machine will execute fuzzy program to
select water level and wash time according to the cloth and weight of the laundries.
The full process is controlled automatically.
Eventhere’snowaterinthetub,thespinningwillstartafteracertainperiod.
Washandspinafterputtingthedamageableclothesintotucknet,toavoidscathe.
Wash the laundries that are prone to lose colors separately from other laundries.
Whenwashingstartoropeningcoverintermitting,thewashingmachinewillbeginto
work after a period time, this is normal phenomenon.
Do not use soak process for woollen laundries.
Procedure program selection method
It has the special power resume function. In the case of power failure or the power plug is
loose during running, the machine can save the running program, and resume the program
after the power supply is recovered. You do not need to set the program again.
1
3
2
Times of pushing the
“PROCESS” button
Selected procedure
program
WASHǃRINSEǃSPIN
(standard program)
Applicable circumstance
Contents(the lighted
indicators indicate the
programs about to run)
When the common laundries need
washing, rinsing and spinning
SPIN
(spin after drain)
When the laundries need only
spinning after manual washing
(first drain then spin)
The laundries are very dirty, or
the sleeves and collars of the shirt
are very dirty.First soak then wash
SOAKǃWASHǃ
RINSEǃSPIN
WASH
(the washing liquid
remains in the tub)
RINSEǃSPIN
WASHǃRINSE
(the rinsing liquid
remains in the tub)
Repeat using the washing liquid
When prevent the laundries
from corrugating,and the
laundries do not need spinning
When the laundries need rinsing
and spinning after manual washing
Push the “PROCESS” button for 6 times, and it will resume the initial mode.
It will circulate in that sequence.
SOAK WASH RINSE SPIN
SOAK WASH RINSE SPIN
SOAK WASH RINSE SPIN
SOAK WASH RINSE SPIN
SOAK WASH RINSE SPIN
SOAK WASH RINSE SPIN

13
Push the “ ” button, select suitable water level
Push the “ ” button to select suitable delay wash program
After switching on the power, when select the standard program,the washing machine will
execute fuzzy program automatically to detect the cloth .After detection, it can set the water
level automatically. To select other water level, ¿rst push the “START/PAUSE” button, then
push the “WATER LEVEL” button to set the water level.
z
After switching on the power, the delay time program is set to off mode automatically. If you
need to set the washing procedure to be ¿nished at delay time, please push the “DELAY”
button to set the delay wash program. Refer to delay button in Page 11 for selection.
Con¿rm the operation of “DELAY” program
When the “zDELAY” function is activated, the indicator light of
the program you have set will be off. The “DELAY (HOURS)” and
“REMAIN(MINUTES)” indicator lights will be on. During delay
procedure, push the “DELAY” button to display the delay time
mode.
To change the running program or cancel the delay time setting,z
you need to switch off the power and make new selection.
4
5
Push the “ ” button
6
Close the top lid
7
If the top lid is opened when the machine is spinning, the machine will stop running and alarm.
Finish washing
8
After finishing washing, the washing machine will cut off the power automatically.
Disposal after washing
Please ¿rstpulloffthepowerplugfromthereceptaclebeforecleaning.z
Afterusing,pleasecleanthelintandforeignmaterialsofthelint¿lter etc. in time. Otherwise
it may inÀuence your using the machine.
z
Clean the detergent box and set it on the control panel seat(
applicable for the model HWM65-728):
12
Themethodofdismantle:Pushitup
aslant and gently.
Themethodofinstall:installitupwardsand
aslant and push it in.

14
1
2
3
4
Clean the detergent box with water(applicable for the model
HWM60-728):
Cleaning the lint ¿lter A(applicable for the model HWM65-728)
and the lint filter B(applicable for the model HWM60-728):
Push down the spring piece at the top of the lint ¿lter to make the claws out of the ¿lter cover,
andthenpulloutthelint¿lter to get it down.(figure 1)
The method of dismantlement and installation refer to the usage of the lint filter B.
Put the lint ¿lter into ¿ltercover,andmakeittight.
Make sure the lint ¿lter well installed, or it can inÀuence your use.
Pull the back cover of the lint ¿lter,andthenyoucangetdownitoffthefrontcoverofthe
lint ¿lter.(figure 2) Sweep the rubbish in the lint ¿lter.Put the back cover of the lint ¿lter into
the front cover .
Install
Install
The front cover
of lint filter
Filter cover
The back cover
of lint filter
Dismantle
Dismantle
Detergent box
Filter cover
Lint filter A
Lint filter B
Install
Dismantle
The lint filter must be used during washing.
It must be cleaned in time after each using.
Figure 1 Figure 2 Figure 1 Figure 2
Notes:
The ¿lterscreenofthewaterinletvalveislikelytobeblockedbyforeignmaterialsandz
inÀuence the water inlet. Please clean it with brush every two
months.
If the cabinet is dirty, wipe it with wet clothz
Do not Àush it directly with water.z
Wipe it with neutral detergent.z
Donotwipeitwiththinner,petrol,alcoholetc.z
Afterwashing,closethewaterfaucet.z
(Ifneeded,youcandismantlethewaterinlethose).
Do not store water in the washing machine for a long period.z
Drain the water completely after each using.
Besuretopulloffthepowerplugbeforemaintenance.z
Hangupthepowercordanddrainhose.z
Wipeoffthewaterdropsonthesurfaceofthemachineandinsidethetub.Openthetoplidz
for some time ( about 1 hour), then close the top lid.

15
Trouble-shooting Answer to question
Phenomena The reason How to settle
ThedigitrondisplaysE0. Thetoplidisopenduring
reserve procedure.
Closethetoplid.z
Thedrainagecannot
work,oristooslow.The
digitron displays E1.
Is the drain hose put down?
Is the drain hose blocked?
Put down the drain hose. Open and
Cleantheforeignmaterial.Openand
z
z
closethetoplidonce.
closethetoplidonce.
It stops running in
midway. The digitron
displays E2.
Thetoplidisnotclosed. Closethetoplid.z
Thesafetyswitchacts,
and the spinning cannot
work. The digitron
displays E3.
Are the laundries put slantingly?
Is the machine slanting?
Reorder the laundries. Close the top lid.z
Place the machine horizontally, open
and close the top lid once.
z
The water ¿lling does
notwork,orisslow,the
digitron displays E4.
Isthewatertapopened,oris
therewatersupplyfailure?
Isthewaterinletvalveblocked?
Isthewaterpressuretoolow?
Open the water tap. Open and close thez
top lid once.
Clean the water inlet valve then openz
and close the top lid once.
Useafterthewaterpressureisnormal.z
The digitron displays E6. The water level sensor is bad. Please contact the after-sales servicez
department.
The
machine
does not
act
Notwash Istherepowerfailure?
Is the power plug inserted tightly?
Isthewaterlevelreachedpreset
position?
Pleaseuseitwhenthere’spowerz
supply.
Insert the power plug tightly.z
Fill water to the preset position.z
Not spin Is the power plug inserted tightly?
Isthetoplidclosedreliably?
Are the laundries set Àat?
Insert the power plug tightly.z
Closethetoplid.z
Set the laundries Àat.z
The water tap leaks
There is abnormal sound
inside the machine
Is the screw of the jointer of water
inlet hose loose or awry?
Is the machine slanting?
Are the laundries put slantingly in
spinning?
Are there any foreign materials?
Fasten the screw of the jointer properly.z
Adjust the machine to be even
Reorder the laundries and close the top
lid.
Remove the foreign materials.z
z
z
(If there’s breakdown, please pull off the power plug before checking)
The following phenomena are not breakdowns sometimes. Please con¿rmagainbeforesendingitto
repair.
Iftherearerealbreakdowns,pleasecometothespecialmaintenancedepartmentorafter-sale
servicedepartmentofourcompany.Donotrepairitbyyourself.

Speci¿cation
Water level / Water quantity (about)
EXTRA LOW/16L, LOW/24L, MEDIUM/32L,
HIGH/40L, MAXIMUM/46L
EXTRA LOW/21L, LOW/29L, MEDIUM/37L,
HIGH/44L, MAXIMUM/51L
Injection pressure
HWM60-728
HWM60-728
HWM65-728
HWM65-728
0.03 MPa ~ 1.0 MPa
Washing/spinning capacity
6.5kg/6.5kg
6.0kg/6.0kg
Phenomena Explanation
Thespinningisintermittentwhenitstarts. Balancethelaundriestoavoidslanting.
Pushthe“spin”buttontoselect“Spin”,butitdoesn’t
work.
Theprogramissettingthedraintime.Sometimeis
needed before it starts spinning.
There may be some water flowing out of the drain hose
in the first use of the machine.
The wash procedure is paused.
It is the water remained in the factory inspection of
performance.
The cloth sensor is checking the cloth, it will add
water after 48 seconds.
The pulsator pauses during water inlet in wash
and rinse.
It is to avoid splashing during water inlet.
When the power plug is inserted,computer board
indicatorisswitchedon,andthemachinestarts
working.
Itisthespecialresumefunction.Inthecaseofpower
failureorthepowerplugislooseduringwashing,the
machinecansavetherunningprogram,andresume
the program after the power supply is recovered. You
donotneedtosettheprogramagain