Haier HWM80-0528 User manual

Fully Automatic Washing Machine
with Pump
User's manual
Fully Automatic Washing Machine
With Pump
ser's m nual Ua
This manual is for
Please read this manual
carefully before using.
Retain it for future reference.
HWM80-0528
User's manual
0030805169K

CONTENTS
Names of the parts……………………………………1
Safety precautions… … … … … … … … … … … … … … 2
Installation and adjustment…………………………4
Install the water inlet hose……………………………6
Preparation before washing…………………………8
Put in the laundries…………………………………9
Usage of the detergent ………………
… … … … … … … … … … … … … … …
Use the operation buttons……………………………10
Finish washing………………………………………12
Disposal after washing………………………………13
Trouble-shooting Answer to question……………14
Packing list……………………………………………15
Specification………………………………………………16
………… …… 9
Close the top lid 9

Control panel
Inner tub
Detergent box
Top lid component
Balance ring
Lint filter
Pulsator
Front control
board
Cabinet
Adjustable leg
Fixed leg
(3 pieces)
Adjustable
leg film
Handle
Water absorption
cushion
Water valve
Back cover
1
Names of the parts
Contents marked with that symbol are related to the
safety of the product and the personal safety of the
users. Please operate in strict conformity to the
contents, otherwise it may cause damage of the
machine or injure the personal safety of the user.
Contents marked with that symbol are actions forbidden
to perform. Performing of those actions may result in
damage of the machine or injure the personal safety of
the user.
Meaning and description of the symbols
Warning sign
Forbidden sign
Drain protective lid
Drain ho se
(installed by user)
Screw cover
Hook

2
Safety precautions
Do not let the machine share one receptacle with
other electric appliances. If the plugging into the
receptacles loose, do not use the plug any more.
If washing machine is supplied from a cord
extension set or electrical portable outlet device,
no cord extension set or electric portable outlet
device should be positioned so it is not subject to
splashing or ingress of moisture.
Do not wash water-proof
laundries like the raincoat, bike
covers etc. to avoid abnormal
vibrations in spinning.
Do not put the machine at damp place
like the bathroom. Never wash it with
water. Do not put wet laundries on the
control panel.
Do not use water hotter than 50℃.
In case the washing machine is installed
on ground with carpet, do not block the
ventilation hole with carpet.
Ensure carpet does not
obstruct the
opening in
the bases.
Please plug the power plug on special
receptacle. Be sure to use three-pins
power receptacle. Ensure that the earthing
prong of the power receptacle is earthed
reliably. Use leakage protector if possible.
Do not bend ,extend, twist, bind by force. Do not press or nip it with weight.
Keep the pin of the power plug clean, if the power plug is polluted with dust,
please wipe with dry cloth carefully.
If the supply cord is damaged, it must be replaced by
the manufacturer or its service agent or a similarly
qualified person in order to avoid a hazard.
The washing machine must be positioned
so that the plug is accessible. Be sure to pull
the plug off and close the water faucet in
following cases: power failure, delivering
the machine, setting the machine idle or
cleaning the machine.
Do not plug or pull the
power plug with wet
hand.
50 C
The ventilation holes
at the bottom
Carpet

Do not put hand into the rotating tub.
It is dangerous even if the rotation
speed is slow. Take special care of the
children. Keep children awa y from the
washing machine to avoid them climbing
on it.
The appliance is not instruct for use of
young children of infirm persons wi thout
supervision.
Young children
should be
supervised to
ensure that they
do not play with
the appliance.
Do not decompose, repair or alter
the machine by yourself.
Do not put any hot or heavy items
(such as the kettle with hot water) on
the washing
machine.
Do not wash laundries with volatile
materials (such as
thinner,
petrol etc.).
Keep the machine away from
direct sunlight and heat source
like the heater.
The handicapped or children shall
not use the machine without care.
Benzene
Safety precautions
To prevent the lint in the tub from blocking the
cascade outlet and influencing the cascade
effect, please keep the lint filter in good
condition, and install it to proper position
during washing. If the lint filter is lost or
damaged, please contact the local
after-sales service department of our company.
3
To protect your laundries and washing
machine, please take out all of the coins,
buttons, sand, hairpin and other foreign
materials before washing.
Please check if the water faucet is open, and if the connection of the water inlet pipe is proper.
It is suggested to use foamless washing powder.

Install the bottom plate
After you open the package, please lean
the washing machine gently down on Soft
object ( like the towel cloth,blanket, etc. ).
Install the bottom plate to the bottom of the
machine with the eight screws by a cross
screwdriver, then lift the machine up gently.
See to the figure:
4
Please install and adjust the machine according to the requirement of
the manual. It is very important to your security and correct
operating the machine.
Installation and adjustment
The largest allowable slope of the shank base of the machine is 2°.The
slanting or rough ground will result in unstable running or stoppage of the
machine. Please adjust it with following methods:
Confirm it's horizontal:
Hang the lead line to check if it is
horizontal.
Adjust the adjustable leg:
≤2゜
Adjust the Installation position
1 .To twist the adjustable leg, please first
lift up the side of the leg slightly, loosen
the adjustable nut, and twist the leg.
2 . After adj ust ment , fast en the nut .
After opening the package, please take out the lint
filter from the document bag, install it to the inner
tub. See to the figure.
Install the lint filter
Inner tub
Lint filter
Fasten
Loosen
High Low
the adjustable nut
the adjustable
feet
Soft object
Bottom plate
Back
Screw
Front

5
How to change the direction of the drain hose
1.Dismantle the back cover of the washing
machine.
3.Dismantle the protecting cover of the
drain outlet at the other side (method
the same as the bushing). Install the
bushing as per indicated in Figure 4.
4.Extend the drain hose from the other
side. Fix the drain hose onto the base
frame with the drain hose frame. (As
indicated in Figure 5)
5.Install the protecting cover of the drain
outlet at the other side as per indicated
in Figure 6.
Drain outlet
protecting cover
Drain hose bushing Drain hose bushing
Figure 1
Figure 4
Figure 5
Figure 6
Drain hose
bushing
Take off
Drain hose
bushing claw
Cabinet
Figure 2
Figure 3
Inner
Press
Press
Outer
2.Put down the drain hose. Take off the
drain hose frame. As indicated in Figure
1, put the drain hose into the cabinet.
Then stretch one hand into the cabinet
to nip the claw of the drain hose bush-
ing to remove the claw from original
position. Take off the drain hose bush-
ing with the other hand. (As indicated in
Figure 2 and 3).
Drain hose frame
Outer
drain
hose
Usage of the drain hose
1.Put the drain hose up to suitable position.Do not
put it on ground.
2.Do not tramp or press the drain hose.
0.8<H<1.2m
H

Water tap,suitable Water tap,not suitable
It is required that the front end shall be longer than 10mm.
The outlet end surface of the tap shall be flat and smooth. If not please file it to
avoid leakage.
2.Loosen the screw till the water tap can be accessed. Put the jointer of the water
inlet hose on the tap. See to Figure 2. (If the tap diameter is too large and the jointer
can not be set on the water tap, please loosen the four screws and take out the
bushing in the jointer. See to the figure3.)
1.Press the lower end of the lock lever and push down the slider. Take off the water
inlet hose jointer from the water inlet hose component. See to Figure 1.
Remarks: Before twisting the fastening nut, the thread is 4mm above the
upper surface of the nut. After twisting the fastening nut, the thread is 2mm
above the upper surface of the nut. See to Figure 6.
4.Take off the nameplate. Twist the fastening nut as per the indication of the figure.
See to Figure 5.
3.Fasten the four screws evenly. See to Figure 4.
>10mm
Outlet end surface
Nut
About 4mm before twisting
About below 2mm after twisting
Screw
Screwdriver Mark label bushing
Figure 2
Figure 5
Figure 1
Figure 4
Figure 3
Figure 6
Slider
Water inlet pipe jointer
Water inlet pipe
Locking lever
Install the water inlet hose
Confirm the water tap
Connection between the water inlet hose jointer and
the water tap
6

1.Do not take off the water absorption
cushion. Please check if the cushion
is dropped or damaged before each
usage. If it happens please contact
our after-sale department immediately.
2.Put the nut of the water inlet hose on
the valve jointer.
3.Fasten the nut. Swaying it gently to
confirm if it's suitable.
1.Close the water tap.
2.Press the locking lever. Push down the slider. Then
pull off the water inlet hose. If the machine is used
more than once every week, the jointer of the water
inlet hose can be kept on the tap to prevent
damaging the fixing screw.
1.Push down the slider. Insert the
water inlet hose into the jointer.
2.Hang the lock lever to the jointer.
Release the slider till a click
sound is heard.
Locking lever
Slider
Water absorption cushion
Nut of the wa ter inlet hose
Jointer of the water inlet valve
Slider
Jointer of the water
inlet hose
Locking lever
Connection between the water inlet hose and the
washing machine
Connection between the jointer of the water inlet
hose and the water inlet hose
Check the connection between the jointer of the
water inlet hose and the water tap
Take down the water inlet hose
1.Swaying the hose gently to confirm if it is fastened stable.
2.After installation, open the tap to check if it leaks.
3.Do not bend the hose with overstrain.
4.Before each usage please check if
the connection between the jointer
of the water inlet hose and the water
tap, and the installation of the
water inlet hose are firm, so as to
prevent dropping from improper
Installation position.
7

8
1.Preparation before washing
Preparation before washing
1.Connect the water inlet hose
2.Confirm that the washing machine is earthed reliably.Then
insert the power plug into the receptacle.Do not connect
the earth terminal to the gas pipe and tap water pipe.
3.Hang up the drain hose.
4.Slanting or uneven
ground may result
in unstable working
or abnormal noise.
Please make the
machine stand horizontally.
Pay attention to followings before washing the laundries
Confirm if
there's
special
requirement
for the
laundries.
Clear the
pocket.
Take out the
coins ,
sand, hairpins
etc.
Fasten the
buttons and
zippers.
When the pulsator
is running ,the
buttons of the
laundries may
cause noise. For
the sake of discretion,
please put the
laundries with
buttons into other
laundries.
The quantity of
the laundries
shall not exceed
the rated value.
The big laundries
like the jeans
shall be put in
loosely.
a. Check if the laundries are applicable for washing with machine.
b. Divide the laundries with unfast color from other laundries.
c. Put those laundries difficult to absorb water into water with hand.
d. For those laundries with heavy soil, please first remove the dirt like mud or dust.
For the parts with heavy soil, please apply detergent in advance, which can make it
easier to remove the soil.
e. For those laundries that may get lint ball and those with long fur, turn it over before
putting in.
f. Do not put those laundries polluted by chemicals directly into the washing machine.
For those small laundries and those may get twisting or worn, and woolen/fur
laundries, please put them into mesh bag for washing.
0.8m H 1.2m≤ ≤