Hailo Professional HS 8 Installation instructions

Assembly and operation shaft cover HS
Assembly and operation shaft cover HS Assembly and operation shaft cover HS
Assembly and operation shaft cover HS 8
88
8
This document includes:
This document includes:This document includes:
This document includes:
-
--
-Mounting dimensions
Mounting dimensionsMounting dimensions
Mounting dimensions
-
--
- Mounting instructions of the cover
Mounting instructions of the coverMounting instructions of the cover
Mounting instructions of the cover
-
--
- Mounting instructions of the gas
Mounting instructions of the gasMounting instructions of the gas
Mounting instructions of the gas-
--
-pressurised springs
pressurised springspressurised springs
pressurised springs
-
--
- Operating instructions
Operating instructionsOperating instructions
Operating instructions
Dated: 21.03.2011
Page 1 / 5
Page 1 / 5
Dated: 21.03.2011

Mounting dimensions of shaft cover HS
Mounting dimensions of shaft cover HS Mounting dimensions of shaft cover HS
Mounting dimensions of shaft cover HS 8
88
8
A T T E N T I O N !!!
A T T E N T I O N !!!A T T E N T I O N !!!
A T T E N T I O N !!!
The circumferential concrete edge must have at least the follo ing
thickness:
for stationary traffic (e.g. car parks) 80 mm
for moving traffic (road ay) 120 mm
These dimensions must also be kept at the rear side behind the hinge
boxes!
The design of the reinforcement must be performed according to the
building statics and is not part of the shaft cover.
Dated: 21.03.2011
Page 2 / 5
Dated: 21.03.2011

Installation instructions shaft cover HS
Installation instructions shaft cover HS Installation instructions shaft cover HS
Installation instructions shaft cover HS 8
88
8
Dated: 21.03.2011
Page 3 / 5
1. Remove all accessory parts such as gas-pressurised springs and operating keys as ell as packaging (film, cardboard)
2. Position the shaft cover in the component here it must be installed, e.g. opening in the building, casing of a shaft
ceiling, etc. There are hooks at the corners of the frame for lifting; on these hooks it is possible to attach chains or ropes to
the cover. Make sure to observe the minimum thickness of the circumferential concrete on the outer edges of the shaft
cover:
- 80 mm for stationary traffic
- 120 mm for moving traffic
The horizontal alignment must be performed according to the final road ay. It is necessary to support the frame round
about from beneath in order to align it.
3. Produce the linkage to the reinforcement according to the statics of the building; seal the gaps bet een the frames and
the casing through hich concrete might penetrate. For large covers it is possible to position ballast eight on the cover in
order to avoid floating. Concrete quality C20/25 (B25) or higher!
4. Spread the concrete hen pouring it using an internal vibrator, finally smooth it and remove concrete spatters from the
cover surface. Allo concrete to set.
5. After setting of the concrete it is possible to open the cover. Mount and adjust the gas-pressurised springs according to
the instructions. All necessary scre s are premounted. If concrete penetrated inside the cover, remove it!
ATTENTION:
ATTENTION: ATTENTION:
ATTENTION:
In case of non
In case of nonIn case of non
In case of non-
--
-observance of the installation instructions the arranty of the manufacturer is becoming null and void!
observance of the installation instructions the arranty of the manufacturer is becoming null and void! observance of the installation instructions the arranty of the manufacturer is becoming null and void!
observance of the installation instructions the arranty of the manufacturer is becoming null and void!
Page 3 / 5
Dated: 21.03.2011

Assembly and operating instructions
Assembly and operating instructionsAssembly and operating instructions
Assembly and operating instructions
Hailo
Hailo Hailo
Hailo -
--
- Shaft cover HS
Shaft cover HSShaft cover HS
Shaft cover HS8
8 8
8 gas
gasgas
gas-
--
-pressurised springs
pressurised springspressurised springs
pressurised springs
It is possible to adjust the action of the gas-pressurised springs by using a relocatable stop.
1. First the head of the piston rod is scre ed to the bottom of the frame using the preassembled scre . Only
tighten the nut as far that it is still possible to turn the scre !
2. Then assemble the head of the cylinder as illustrated; hen moving the cover the scre slides in the oblong
hole.
3. When fixing the stop (scre ith sleeve, position "X") it can be adjusted to the point at hich the gas-
pressurised spring pushes up ards hen opening the cover. If the shaft cover is only equipped ith one gas-
pressurised spring, it is necessary to adjust the point at hich cover stops hen it opens to about 80°. Then it is
easily possible to move the cover manually to the stop position.
If several gas-pressurised springs are available, it is necessary to mount the stops in a ay that the gas-
pressurised springs are activated one after another. The advantage is that the cover ould not open rapidly and
Dated: 21.03.2011
pressurised springs are activated one after another. The advantage is that the cover ould not open rapidly and
that you must not counteract all gas-pressurised springs hen closing the cover. The further the stop is displaced
do n ard the higher is the force of the spring hen starting opening the cover.
Page 4 / 5
Dated: 21.03.2011

Operating instructions
Operating instructionsOperating instructions
Operating instructions
Hailo
Hailo Hailo
Hailo -
--
- Shaft cover HS
Shaft cover HSShaft cover HS
Shaft cover HS8
88
8
The operating key # 9515-03 and, if applicable, the key of the profile cylinder in the cylinder lock (optionally)
are required to operate the shaft cover HS8.
1. Unscre the triangle head cap locking bolt (s) of the locking by means of the operating key and position it at
a clean place (illustration 1)
2. If available, unlock and remove the cylinder lock by means of a key
3. Unscre the triangle locking nut(s) (illustration 2 and 3)
4. Seize into the opening in the cylinder collar using the hook of the key and lift the cover (illustration 4)
5. The gas-pressurised springs help to open the cover to about 80°, then continue opening the cover manually
until the snib locks in place (illustration 5)
Dated: 21.03.2011
6. Unlock the snib in order to close the cover and perform steps 5 through 1 in reverse order
Illustration 1 Illustration 2
Illustration 3 Illustration 4
Illustration 5
Observe the maintenance and care regulations! (Label on the shaft cover)
Page 5 / 5
Observe the maintenance and care regulations! (Label on the shaft cover)
Dated: 21.03.2011