Halo PRIME550 User manual

1
ESSENTIALS GUIDE

2
08
INDUSTRY'S FIRST RECHARGEABLE BATTERY
OPERATED OUTDOOR PELLET GRILL
TABLE OF CONTENTS04
MEET THE PRIME550 OUTDOOR PELLET GRILL 06
FEATURES OF YOUR PRIME550
COOKING + CAPACITY 09
10
TEMPERATURE SETTINGS
11
OWNER'S MANUAL
27
LEVELING YOUR PRIME550
38
PRIME550 PARTS LIST
16
PRIME550 OPERATING INSTRUCTIONS
12
CSA - EN
25
CARING FOR YOUR PRIME550
FIVE (5) YEAR LIMITED WARRANTY 41
34
TROUBLESHOOTING
40
ASSEMBLED DIMENSIONS
15
PRODUCT RECORD
28
PRIME550 PELLET CLEAN-OUT 29
TIPS + TECHNIQUES 32
CONVERTING YOUR PELLET GRILL
37
ELECTRICAL WIRE DIAGRAM

3
44
MANUAL DEL PROPIETARIO
61
NIVELANDO SU PRIME550
72
LISTA DE PARTES DEL PRIME550
50
PRIME550 INSTRUCCIONES DE OPERACIÓN
45
CSA - ESPAÑOL
59
CUIDANDO SU PRIME550
GARANTÍA LIMITADA DE CINCO (5) AÑOS 75
68
SOLUCIÓN DE PROBLEMAS
74
DIMENSIONES ENSAMBLADAS
49
REGISTRO DEL PRODUCTO
62
LIMPIEZA DE PELLET DEL PRIME550 63
CONSEJOS + TÉCNICAS 66
CONVIRTIENDO SU PARRILLA DE PELLET
71
DIAGRAMA ELÉCTRICO DEL PRIME550
78
MANUEL DU PROPRIÉTAIRE
95
MISE À NIVEAU DE VOTRE PRIME550
106
LISTE DES PIÈCES DU PRIME550
84
MODE D'EMPLOI DU PRIME550
79
CSA - FRANÇAIS
93
ENTRETIEN DE VOTRE PRIME550
GARANTIE LIMITÉE DE CINQ (5) ANS 109
102
DÉPANNAGE
108
DIMENSIONS ASSEMBLÉES
83
FICHE PRODUIT
96
NETTOYAGE DES GRANULÉS DU PRIME550 97
CONSEILS ET TECHNIQUES 100
CONVERSION DE VOTRE GRIL À GRANULÉS
105
SCHÉMA ÉLECTRIQUE DU PRIME550

4
MEET THE
Nothing says Cook, Gather and Create Memories like pellet grilling!
The HALO PRIME550was created with you in mind. Our patented igniter
system allows the Prime550 to be powered by a 12-Volt 5Ah Rechargeable
Lithium-ion Battery Pack. Unthetered for the perfect outdoor kitchen
addition or on-the-go camping, picnicking and tailgating companion!
We strive to Rise Above in both who we are and what we create. Our mission
is to be a catalyst for re-connecting people and enhancing the experience
of cooking outdoors - In the greatness of nature, on-the-go, and in your
backyard.
The entire team here at Halo thanks you for joining our community. We look
forward to serving you by listening and continuing to bring you authenticity,
versatility and innovation.
-

5

6
Perfect for cooking large cuts of meat.
Sear, roast and smoke at temperatures from 180°F-500°F.
Unthethered for true portability.
554 i n 2TOTAL COOKING SURFACE
Larger capacity holds up to 14.2 lb at once for a longer cook.
14.2 LB HOPPER CAPACITY
WIDE RANGE TEMPERATURE
NEW TECHNOLOGY
LITHIUM-ION BATTERY OPERATED OR A/C ADAPTER
FEATURES OF YOUR
6High intensity spark ignition system.
NEW TECHNOLOGY
IGNITER SYSTEM

7
TUCKAWAY
WARMING RACK
WIRED MEAT PROBE
DIRECT SEAR + FLARE-UP CONTROL PLATE
LARGE DIGITAL
CONTROLLER DISPLAY
Easily view temperature
display.
Adjust the damper on center
vent to sear meats for even
distribution.
Heat to an accurate
desired temperature.
Tucks away for clear viewing of
food when open and continues
food warming when closed.
7
Set and adjust temperatures
automatically from the Halo app.

8
8BATTERY NOT INCLUDED. Requires (1) 12-volt 5Ah Rechargeable Lithium-ion Battery Pack for auger and igniter. 8
RECHARGEABLE BATTERY
Our patented igniter system allows
the PRIME550to be powered by a
12-volt 5Ah Rechargeable
Lithium-ion Battery Pack.
Untethered for the perfect outdoor
kitchen addition or on-the-go, camping
and tailgating companion.
GAME CHANGER.
8

9
OR
SEAR
ROAST
SMOKE
COOKING +CAPACITY
HIGH
350-500°F
(176-260°C)
MEDIUM
250-350°F
(121-176°C)
LOW
180-250°F
(82-212°C)
Best for...
Pork Shoulder
Beef Brisket
Whole Turkey
Best for...
Whole Chickens
Scotch Eggs
Beef Roast
Best for...
Hamburgers
Steak
Vegetables
4Rib
Racks 4Whole Chickens 24Beef Patties
OR
total cooking space:554 in2total weight:110.23 lbs. pellet hopper capacity:14.2 lbs. max temerature:500°F (260°C)

10
TEMPERATURE SETTINGS
■ Temperature readouts on the controller may not
exactly match the thermometer.
■ All temperatures listed are approximate and are
affected by outside ambient temperature, wind, the
quality of pellet fuel being used, the lid being opened,
and the food quantity being cooked.
HIGH
MEDIUM
LOW
350-500°F
250-350°F
180-250°F
This temperature range is used to sear meat at high heat, without
any contact with ame. High temperature is also used as the burn-o
temperature to clean o the cooking grid before and after use. In addition,
high heat can be used in extreme cold weather conditions to compensate
for the contrast of temperatures between outside and inside the unit.
This temperature range is best for roasting and nishing o that slow
smoked creation. Cooking at these temperatures will greatly reduce the
chances of a grease are-up. Great range for cooking anything wrapped in
bacon, or where you want versatility with control.
This range is best used to slow smoke, increase smoky avor, and to
keep foods warm and keep your meats juicy by cooking longer at a lower
temperature.
10
(176-260°C)
(121-176°C)
(82-212°C)

11
SCAN FOR
Product Registration
Online Owner’s Guide
Assembly Videos
11
OWNER'S MANUAL
MODEL NO: HS-1001-XNA
Halo Products Group LLC
850 West Park Rd Elizabethtown KY, 42701
Toll free: 1-833-572-1688
FOR OUTDOOR USE ONLY.
″A MAJOR CAUSE OF FIRES
IS FAILURE TO MAINTAIN
REQUIRED CLEARANCES (AIR
SPACES) TO COMBUSTIBLE
MATERIALS. IT IS OF UTMOST
IMPORTANCE THAT THIS
PRODUCT BE INSTALLED ONLY
IN ACCORDANCE WITH THESE
INSTRUCTIONS.″
WARNING
"Please read this entire
manual before installation
and use of this pellet-burning
appliance. Failure to follow
these instructions could result
in property damage, bodily
injury, or even death."
WARNING
• "READ ALL INSTRUCTIONS
BEFORE INSTALLING AND
USING THIS APPLIANCE."
• "SAVE THESE INSTRUCTIONS."
WARNING

12
IMPORTANT SAFETY INFORMATION
• Regular care and maintenance is required to prolong the lifespan of
your HALO pellet grill. If the pellet grill is stored outside during the
rainy season or seasons of high humidity, use a HALO grill cover to
ensure rainwater does not get into the hopper.
• Do not transport your pellet grill while in use or while is hot. Ensure
the re is completely out and that the pellet grill is completely cool
to the touch before moving.
• Wood pellets will expand signicantly when wet or exposed to
high humidity, decompose, and may jam the feed system. Always
disconnect the power, before performing any service or maintenance.
• OUTSIDE STORAGE: "CAUTION!" If the grill is stored outside during
the rainy season, care should be taken to ensure that water does not get
into the pellet hopper. Wood pellets expand greatly when wet and will
jam the auger. Always cover your grill when not in use with the Halo Grill
Cover. This custom t cover can be purchased at www.halo-pg.com.
Follow these guidelines to prevent this colorless, odorless gas from
poisoning you, your family, your pets, or others:
• Recognize the symptoms of carbon monoxide poisoning: headache,
dizziness, weakness, nausea, vomiting, sleepiness, and confusion.
Carbon monoxide reduces the blood’s ability to carry oxygen. Low
blood oxygen levels can result in loss of consciousness and death.
• Seek a doctor if you or others develop cold or u-like symptoms.
Carbon monoxide poisoning, which can easily be mistaken for a cold
or u, is often detected too late.
• Alcohol consumption and drug use increase the effects of carbon
monoxide poisoning.
• ″Never use gasoline, gasoline-type lantern fuel, kerosene, charcoal lighter
uid, or similar liquids to start or ’freshen up’ a re in this appliance. Keep
all such liquids well away from the appliance when in use.″
• In the event that the re in the repot goes out while smoking and
there are still sufcient pellets in the pellet hopper, it is important to
follow these steps. Failure to do so may cause a hazardous “overring”
of your grill due to an excess of unburned pellets in the repot.
WARNING
• “Contact local building or re ofcials about restrictions
and installation inspection requirements in your area.”
• "Never use gasoline, gasoline-type lantern fuel, kerosene,
charcoal lighter uid, or similar liquids to start or ʼfreshen
upʼ a re in this appliance. Keep all such liquids well away
from the appliance when in use."
• Caution against unattended cooking:
- "Remove pots and pans while the operating appliance
is unattended, to reduce the risk of re."
- "DO NOT use accessories not specied for use with this
appliance."
DANGERS AND WARNINGS
• Keep electrical supply cords and the fuel away from heated surfaces.
Do not use your pellet grill in the rain or around any water source.
• After a period of storage, or non-use, check the burn pot for
obstructions, the hopper for foreign objects, and any air blockage
around the fan intake or rear barrel exhaust holes. Clean before use.
DANGER
CAUTION
This product can expose you to chemicals, including carbon
monoxide, which are known to the State of California to cause cancer
and birth defects or other reproductive harm. For more information
go to www.P65Warnings.ca.gov
WARNING
CALIFORNIA PROPOSITION 65
• A minimum clearance of 36” (914.4 mm) from combustible
constructions to the sides of the pellet grill from the back of the pellet
grill to combustible constructions must be maintained.
WARNING
• Any limitations joining of two or more parts to constitute an
assembly, such as installation of support legs, enclosures and the like.
• Do not use this appliance indoors, in an enclosed unventilated area,
under an overhead combustible ceiling or overhang. Keep your pellet
grill in an area clear and free from combustible materials, gasoline
and other ammable vapors and liquids.

13
Ashes should be placed in a metal container with a tight-tting lid. The
closed container of ashes should be placed on a non-combustible oor
or on the ground, well away from all combustible materials, pending nal
disposal. When ashes are disposed by burial in soil, or otherwise locally
dispersed, they should be retained in a closed container until all cinders
have thoroughly cooled.
WARNING
DISPOSAL OF ASHES
Make sure to clean out the ash from the burn pot after each use to ensure
the proper function of your pellet grill. Failure to clean out the ash from
burn pot after each use may cause the pellets not to ignite or may cause
a build-up of pellets in front of the auger tube potentially causing a burn
back inside the auger tube.
WARNING
• This pellet cooking appliance is designed and approved for pelletized, all
natural, wood fuel only. Any other type of fuel burned in this appliance will
void the warranty and safety warning.
• You must only use all natural wood pellets, designed for burning in pellet grill.
• ″Use Only Wood Pellet Fuel Specied By The Manufacturer. Do Not Use
Pellet Fuel Labeled As Having Additives.″
• You must only use all natural wood pellets designed for burning in pellet grills.
• ″Do not use accessories not specied for use with this appliance.″
The pellet mean heating value in 30,000 BTU/LB(31,651 KJ/Kg), ash
content < 1%.
There is no industry standard currently for barbecue wood pellets,
although most pellet mills use the same standards to make wood pellets
for domestic use. Further information can be found at www.pelletheat.org
or the Pellet Fuel Institute.
Please contact your local food-grade pellets dealer on the quality of
pellets in your area, and for information on brand quality. As there is no
control over the quality of pellets used, moisture affected pellets. Halo
Products Group LLC undertakes no responsibility for damage to the
appliance caused by poor quality of fuel.
WOOD PELLET FUEL
WHAT DO YOU NEED TO KNOW ABOUT CREOSOTE?
Creosote, or soot, is a tar-like substance. When burning, it produces
black smoke with a residue which is also black in color. Soot or creosote
is formed when the appliance is operated incorrectly, such as: blockage
of the burn pot, blockage of the combustion fan, failure to clean and
maintain the burn area, or poor air-to-fuel combustion.
"Creosote – Formation and Need for Removal. When wood pellets are
burned slowly, they produce tar and other organic vapors that combine
with expelled moisture to formcreosote. The creosote vapors condense
in a relatively cool oven ue and exhaust hood of a slow burning re.
As a result, creosote residue accumulates on the ue lining and exhaust
hood. When ignited, this creosote makes an extremely hot re."
It is dangerous to operate this appliance should the ame become dark,
sooty, or if the burn pot is overlled with pellets. When ignited, this
creosote makes an extremely hot and uncontrolled re, like a grease re.
Should this happen, turn the unit off, let it cool completely, then inspect for
maintenance and cleaning. It commonly accumulates along exhaust areas.
If creosote has formed within the unit; allow the unit to warm up at a
low temperature, turn off the appliance, then wipe away any formation
with a hand towel. Like tar, it is much easier to clean when warm, as it
becomes liquid.
"The grease duct should be inspected at least twice a year to
determine when grease and/or creosote buildup has occurred."
"When grease or creosote has accumulated, it should be removed to
reduce risk of re."
WARNING
CARBON MONOXIDE "SILENT KILLER"
Carbon monoxide (CO) is a gas that can kill you quickly. It is called the
"silent killer" because it is colorless, odorless, tasteless and non-irritating.
It's colorless, odorless, tasteless gas produced by burning gas, wood,
propane, charcoal or other fuel.
Carbon monoxide reduces the blood's ability to carry oxygen. Low blood
oxygen levels can result in headaches, dizziness, weakness, nausea,
vomiting, sleepiness, confusion, loss of consciousness or death. Follow
these guidelines to prevent this colorless, odorless gas from poisoning
you, your family or others:
"Carbon monoxide is especially toxic to mother and child during
pregnancy, infants, the elderly, smokers and people with blood or
circulatory system problems such as anemia or heart disease."
Alcohol consumption and drug use increase the effects of carbon
monoxide poisoning.
See a doctor if you or others develop cold or u-like symptoms while
cooking or in the vicinity of the appliance. Carbon monoxide poisoning,
which can easily be mistaken for a cold or u, is often detected too late.
RECHARGEABLE LITHIUM-ION
BATTERY PACK
IMPORTANT
Read and follow the information contained herein before handling the
rechargeable battery. Keep this document in a safe place.
CSA - ENGLISH

14
Lithium-ion battery re hazards are associated with the high energy
densities coupled with the ammable organic electrolyte. This creates
new challenges for use, storage, and handling. Studies have shown that
physical damage, electrical abuse such as short circuits and overcharging,
and exposures to elevated temperature can cause a thermal runaway. This
refers to rapid self-heating from an exothermic chemical reaction that can
result in a chain reaction thermal runaway of adjacent cells.
LITHIUM-ION BATTERY HAZARDS
• Store batteries away from combustible materials.
• Remove batteries from the device for long-term storage.
• Store the batteries at temperatures between 41°F and 68°F.
• If practical, store batteries in a metal storage cabinet.
STORAGE
• Never charge a primary (disposable lithium or alkaline) battery; store
one-time use batteries separately.
• Charge or discharge the battery to approximately 50% of capacity
before long-term storage.
• Use chargers or charging methods designed to charge in a safe
manner battery packs at the specied parameters.
• Disconnect batteries immediately if, during operation or charging,
they emit an unusual smell, develop heat, change shape/geometry, or
behave abnormally.
• Remove battery pack from chargers promptly after charging is
complete.
• Do not use the charger as a storage location.
CHARGING PRACTICE
• Handle batteries and or battery-powered devices cautiously to not
damage the battery casing or connections.
• Keep batteries from contacting conductive materials, water, seawater,
strong oxidizers and strong acids.
• Do not place batteries in direct sunlight, on hot surfaces or in hot
locations.
• Inspect batteries for signs of damage before use. Never use and
promptly dispose of damaged or puffy batteries.
• Keep all ammable materials away from the operating area.
• Allow time for cooling before charging a battery that is still warm
from usage and using a battery that is still warm from charging.
• Consider cell casing construction (soft with vents) and protective
shielding for battery research and experimental or evolving
application and use.
HANDLING AND USE
Dispose of damaged battery packs that no longer hold a substantial
charge. To check the general condition of your cells, charge them, let them
DISPOSAL
• Keep battery out of sight and reach of children.
• Rechargeable Lithium-ion pack is potentially hazardous and can
present a serious FIRE HAZARD, SERIOUS INJURY and/or PROPERTY
DAMAGE if damaged, defective or improperly used.
• By purchasing the battery, you assume all risks associated with the
battery. We are not responsible for any damages and consequential
damages by using our products. Use at your own risk.
• Do not disassemble or modify the battery on any way. Vibration,
puncture, contact with metals, or tampering with the battery can
cause it to fail.
• Do not disassemble or modify the battery on any way. Vibration,
puncture, contact with metals, or tampering with the battery can
cause it to fail.
• Never leave the battery unattended while charging. If the battery
becomes hot, smokes, swells, or gives off an odor during charging,
terminate charging immediately.
• In the event the battery leaks and the uid gets onto your skin or
into your eyes, do not rub. Rinse well with water and immediately
seek medical care. If left untreated, the battery uid could cause
damage to the eye and skin.
SAFETY TIPS
• THE BATTERY HAS BEEN FULLY DISCHARGED AND IS NOT
RECHARGED SHORTLY AFTERWARD.This potential is aggravated
if batteries are damaged, contain an undetected factory defect, are
used or stored at temperature extremes,or are approaching the end
of their useful life. Ideally, battery should be recharged within 24
hours of a full discharge.
• CHARGING IS ATTEMPTED AT TEMPERATURES BELOW 40°F.
Charging below 40°F causes a chemical reaction in the battery cells
that can cause permanent damage and the possibility of re or
explosion during charging.
• THE BATTERY HAS BEEN EXPOSED TO LIQUIDS, ESPECIALLY
SALT WATER. Exposure to liquids can cause internal corrosion or
damage to the cells or to the Battery Management System (BMS).
The BMS protects the battery from overcharging, high self-discharge
or imbalanced charging of the cells, any of which can present the
possibility of re during recharging.
• OPERATING OR CHARGING A BATTERY THAT HAS BEEN DAMAGED
FROM DROPPING OR FROM SHIPPING DAMAGE. USING A CHARGER
OTHER THAN SPECIFICALLY DESIGNATED FOR THE PARTICULAR
BATTERY.
A FIRE IS MOST LIKELY TO OCCUR DURING THE CHARGING
PROCESS UNDER THE FOLLOWING CIRCUMSTANCES
rest for an hour, then measure the voltage. If your cells are close to 12V, the
battery pack is in good condition.
CSA - ENGLISH

15
PRODUCT RECORD
IMPORTANT:Fill out the product information record below, or to
register your product, visit our website at www.halo-pg.com.
Model Number:
Serial Number:
Purchase Date:
NOTICE: Model Number and Serial Number located on the back of front panel.
REGISTER

16
OPERATING
INSTRUCTIONS
GETTING TO KNOW YOUR
CONTROLLER
CONTROL KNOB
1. Push the control knob once to turn the unit
on. The controller will ash several times
and then turn to a solid screen. This lets you
know your unit is powered on.
2. Push the control knob again, this will take
you to the function screen where you can
access the functions listed previously.
3. Rotate the knob until you see the function you need.
4. Push the control button to lock in after you have chosen the preferred
function.
5. Press and hold the control button to turn the unit o. This will begin
the 10 min cool down timer. The unit will automatically shut o when
the timer has ended.
6. The following page will detail how to set each of the controller
functions.
16
DIGITAL LED SCREEN
This isused asthe informationcenter foryour unit.
Push thecontrol buttononce topower onthe unit.
The LEDscreen willdisplay thefollowing functions:
• Temperature (F or C)
• Timer
• Meat Probe Temperatures (if connected)
• Battery level (if powered by battery)
• A/C adapter icon (if powered by A/C adapter)
• Prime
• Cleanout
• Fan, Auger, Igniter indicator
• Battery REMOVE indicator (when applicable)
POWER
Thereare (2) optionstopoweryour
HALOPrime550 Outdoor PelletGrill:
1. With an A/C adapter that plugs into
grounded (GFCI) outdoor receptacle 120 volt.
2. With a 12V Rechargeable Lithium-Ion
Battery. You can use one power method
or have both the battery and A/C adapter
plugged into the unit at the same time.
Pellet Low

17
CLEAN OUT
The cleanout function is used to remove the last remaining
pellets from the pellet hopper and auger tube.
OPERATING THE CLEAN OUT FUNCTION
1. Push the control knob once to turn the unit on. The controller will ash
several times and then turn to a solid screen. This lets you know your
unit is powered on.
2. Push the control knob again, this will take you to the function screen
where you can access the Temperature (F/C), Time, Meat Probe
Temperature, Prime, and Cleanout functions, as well as the Battery
level, A/C adapter, Fan, Auger, Igniter, and Battery removal indicators
(when applicable.)
3. *Once you've turned the unit on by pushing the control knob* Rotate
the control knob to select the Cleanout function. Push the button to
lock in the cleanout function.
4. The cleanout function is set to run for 90 minutes. The remaining pellets
will be fed through the burn pot into the 5-gallon bucket below. Note:
you can shut o the Clean Out function at any time. You must reinsert
the ash tray back in place before starting the unit. Failure to insert the
tray back may cause re and body injury.
IMPORTANT TO NOTE:
• The unit must be OFF, the AC adapter unplugged, and the battery
removed before cleaning out the hopper manually.
• The unit must be cool before the Clean Out function is initiated. Do not
use this function during startup or cooking foods. Failure to do so may
cause re inside the re pot and cause damage to your pellet grill.
• Place a container large enough to hold the discarded pellets under
the pellet clean-out re pot opening. Pull the ash tray spring and
then slide the ash tray forward to align the ash tray clean out directly
under the re pot to remove any ash. (Note: Release the spring pin as
soon as you start to pull the tray forward to lock the tray into the ash
clean-out position). Pull the ash tray spring pin once more to remove
the tray completely out from the unit to empty the ash. See the
Prime550 Pellet Clean Out section for details.
CONTROLLER FUNCTIONS
After you've turnedthe unit on bypressing the
controlknobyoucanaccessthefollowingfunctions: MEAT PROBE
The plug-inconnection forthe meat probeis onthe left side
of thegrill abovethe battery compartment.The meatprobe
temperature willappear onthe controller afterthe meat
probeisconnected.
1. Push the control knob once to turn the unit ON. The controller
will ash several times and then turn to a solid screen. This lets
you know yourunitis powered on.
2. Push the control knob again, this will take you to the function
screen where you can access theTemperature (F/C), Time, Meat
ProbeTemperature, Prime, andCleanoutfunctions, as well as
theBattery level, AC adapter, Fan, Auger, Igniter, and Battery
removal indicators (whenapplicable.)
3. *Once you've turned the unit on by pushing the control
knob*Rotate the knob to select the Meat Probe function.
4. Push the button to lock in the Meat Probe function, then rotate
the control knob to the desired temperature you want your meat
probe set and push the button to set.
IMPORTANT TO NOTE:
• Disconnect the meat probe from the jack receptacle and cover
the port with the silicone cap when not in use.
• One meat probe is included with the unit.
• Use HALO brand meat probes only to prevent damage to the unit.
• The unit will go into WARM mode and the unit temperature will
reduce when the meat probe reaches the set temperature. This
will keep the food from continuing to cook before it is removed
from the unit.
TEMPERATURE
1. Push the control button to lock in the Temperature function.
2. Rotate the knob to select your desired Temperature.
3. Pushing the control button will now start the unit.
TIME
1. Rotate the knob to select the Time function.
2. Push the button to lock in the Time function. You can set the
number of hours and minutes to time your smoke.
3. Rotate the control knob to the desired number of hours, then push
the control knob to conrm the hours.
4. Rotate the control knob to set the desired number of minutes,
then push the control knob to conrm the minutes.
5. The timer will count down to zero after your unit is started.
DEGREES F/C
1. Rotate the knob to the F (Fahrenheit) or C (Celsius) function and
push the button to lock in this function.
2. Rotate the control knob to either F or C and push the control knob
to lock in your choice.
3. Please note the default setting is Fahrenheit.
PRIME
ThePrime functionallows youtofeedpellets intotheburnpotto initiallystart
yourunitortofeedadditionalpelletsduringasmoketogetmoresmoke.
1. Rotate the knob to select the Prime function.
2. Push and hold the control knob for the prime function to feed additional
pellets.
3. After youare nished priming the pellets into the burn pot, release the
control knob and the auger will stop feeding pellets. 17

18
CONTROLLER INDICATOR
LIGHTS
POWER SOURCE
BATTERY
There will be a battery icon on the
controller after you insert the battery
into the unit to let you know the grill is
powered with battery.
A/C ADAPTER
There will be an AC plug icon on the
controller when the AC adapter is
plugged into your unit to let you know
the unit is powered on with AC power.
BATTERY
WARNING
1. If the controller displays the “REMOVE” icon in
red, the battery needs to be removed from the
unit promptly to prevent any damage to the
battery.
2. This indicates the battery temperature is too high.
Let the grill cool down to ambient temperature,
insert the battery again, and restart the unit.
3. If this persists, please call Consumer Service at
1-833-572-1688.
AUGER: PELLET FEED SYSTEM
The Auger function iconwill appear during startup andswitches ON and OFF duringcooks to
periodicallyfeedthepellets.
1. Delivers the pellets from the pellet hopper, through the auger tube, to the burn pot at a
controlled programed speed for ecient combustion.
2. The amount of time the auger feeds pellets will depend on which temperature you want to
grill or to smoke.
ELECTRONIC
IGNITER
The igniterfunction iconwill appearduring thestartup
and switchesON andOFF duringcooks tomaintain
temperature.
1. This is a type of ignition system that works
electronic circuits, usually by transistors. The
transistors are controlled by sensors to generate
electric pulses which then generate a high voltage
spark that can burn the lean mixture and provide
a better economy and lower emission.
2. The igniter will come back on when the
temperature falls 20 degrees below the set
temperature.
FAN
The fan icon will be lit when the fan is operating.
1. Supplies fresh air to the burn pot for combustion.
2. Generates an even fan-forced heat circulation, so your food cooks evenly on all sides.
3. Helps the pellets burn more eciently.
4. Performs maintenance evacuation of ashes from burn pot during cooking and shutdown
functions.
IMPORTANT TO NOTE:
• Both icons will appear on the controller when
you have both plugged into your grill. Your
grill is powered, but not on at this time.
• The battery will charge in the unit when the
A/C adapter is plugged in. The average time
for a battery to charge is between 5-6 hours.
The alternative way to charge the battery is to
remove the battery from the unit and charge
it with a Halo charging dock. The charging
dock can be acquired at www.halo-pg.com.
18
Pellet Low
PELLET LOW
An infrared sensor insidethe hopper detects when thepellet level is low, andthe Pellet Low icon
willappear.Werecommendthat you add pellets to the hopper so your cookwillnotbeinterrupted.

19
This is the inital start up procedure when you're using
your pellet grill for the rst time.
1.Plug the A/C adaptor power cord into a grounded
(GFCI) power supply or insert the Halo 12 Volt
Lithium Battery (Battery Sold Separately).
2.Remove the grease plate to see the pellets entering
the burn pot when priming the unit. Check the burn
pot to make sure there is no obstruction for proper
ignition. Open the hopper lid. Make sure there
are no foreign objects in the hopper or auger feed
system entry at the bottom of the hopper. Fill the
hopper with dry, all natural barbecue hardwood
pellets.
3.Push the control knob once to turn the unit on, the
screen will ash then turn to solid screen. Push the
control button a second time to get to the function
screen and turn the control button to the Prime
function. Push and hold the control button to start
feeding pellets. Keep holding the button until you
see or hear pellets dropping into the burn pot, then
release the control button.
PELLET GRILL BURN-OFF
IMPORTANT
• Make sure there are some pellets covering the electrode.
• Replace the grease plate and cooking grid into the unit.
• Make sure the searing damper is closed.
4. Push the control knob and rotate to the
Temperature function. Press the control knob.
Rotate the control knob again to set to 350°F (177C),
push the control button to lock in this temp and
start the grill. Allow the unit to preheat for approx.
30-45 minutes. This is used to burn o any residual
oils that might be on the inside of the grill. The lid
must be closed during the burn o cycle.
IMPORTANT
Listen for a roar coming from the burn pot, and notice some heat and
smoke being produced. This lets you know the unit is functioning correctly.
5. The desired temperature for smoking, cooking
or searing can be set after the burn-o period is
complete.
6. Shut the unit down and allow the unit to cool o to
ambient temperature. It may take some time for the
unit to drop to a lower temperature setting.
IMPORTANT
The auger will continue to turn and feed pellets once you select a lower
temperature setting after burn-off. This will momentarily raise the
temperature, but the temperature will eventually decrease and stabilize
at your desired set temperature. Remember, you are trying to regulate the
heat, so time is necessary to achieve your desired set temperature.
This is the standard start up procedure for using your
pellet grill any time after the initial burn-off.
1. Plug the A/C adaptor power cord into a grounded
(GFCI) power supply or insert the Halo 12-Volt
Lithium Battery (Battery Sold Separately).
2. Push the control button once to
turn the unit on, the screen will
ash then turn to a solid screen.
Push the control button a second
time to get to the function
screen. Turn the control button
to the Temperature function.
Push the control button once
PELLET GRILL START UP
19

20
IMPORTANT
Make certain the searing damper is closed.
PELLET GRILL SHUT-OFF
more to conrm the Temperature setting, then
rotate the control button to the desired smoke,
cook or sear temperature. Push the control button
one more time to set the temperature and start the
unit.
3. The ignitor will come on for a few seconds to
conrm the ignition is functioning properly and the
igniter icon will appear on the top of the controller
screen. The unit will feed pellets into the burn pot
and the ignitor will come on again to start your unit.
4. The unit is lit when the temperature on the
controller increases, and smoke is coming from the
back of the unit.
1. When nished
cooking, turn the
temperature dial to
350°F/176°C with lid
closed. Let your pellet
grill run for 10 to 20
minutes to go through its normal cleaning method.
If you have been preparing foods that are extra
greasy, allow the pellet grill to burn-o for an extra
10 to 20 minutes. This will reduce the chance of
causing a grease re for the next start-up.
2. To turn your unit OFF, push and hold the control
knob until the fan increases speed and the
controller screen displays a 10-minute countdown.
The unit will now begin its automatic cool-down
cycle. The auger system will stop feeding pellets,
the ame will burn out, and the fan will continue
to run until the cool-down cycle is complete. The
shutdown mode will last 10 minutes.
3. After the cool down cycle is complete, if using
power from A/C adapter, unplug from the electrical
outlet. If using battery power, you can remove the
battery from the battery housing by pushing in on
the battery- it will spring back to disconnect from
the controller.
4. Replace the battery with the faux battery case
that comes with the unit to ensure they remain
protected from environmental factors such as
humidity, water, and dirt. You can also charge the
battery by leaving the battery in the housing with
A/C plugged in. The battery will replenish its full
energy within 5-6 hours.
• It may take about 20-30 minutes for the temperature to stabilize
based on the type or brand of pellets you are using. If you are
having ignition issues, you may need to open the searing damper
during the startup procedure to ensure proper ignition. This can
also be affected by the type or brand of pellets you’re using.
• This pellet grill has a searing damper feature. It is recommended
when smoking food, the searing damper is closed to help obtain
consistent temperatures across the whole cooking surface.
• The sear feature is used to quickly sear a piece of food over an
open ame. This is typically done at the higher temperature
settings (350°F – 500°F) after your smoke is complete.
• The searing damper is in the closed position when the searing
damper handle is pushed toward the pellet grill body and in the
open position when the handle is extended away from the pellet
grill body.
• The hopper capacity is approx. 14 lbs. of pellets. This will typically
last between 10-20 hours depending on the temperature setting.
Make sure your hopper is full before you start your smoke or cook.
This will ensure that you will not have to rell the hopper during
your smoke.
IMPORTANT
20