Halsey Taylor OVL-EBP User manual

97638C (Rev. H - 5/08)PAGE1
OVL-EBP*C, OVL-SBP*C, OVL-SEBP*F, OVL-ESBP*F
HalseyTaylorOwnersManual
Non-Refrigerated Fountains
Toassureyouinstallthismodeleasilyandcorrectly,
PLEASEREADTHESESIMPLEINSTRUCTIONSBEFORESTARTINGTHE
INSTALLATION.CHECKYOURINSTALLATIONFORCOMPLIANCEWITH
PLUMBING,ELECTRICALANDOTHERAPPLICABLECODES.Afterinstallation,leave
theseinstructionsinsidethefountainforfuturereference.
IMPORTANT
ALLSERVICETOBE PERFORMEDBY ANAUTHORIZED SERVICEPERSON
FIG. 1
TUBE IS
SECURED
IN POSITION
SIMPLY PUSH IN
TUBE TO ATTACH PUSH IN COLLET TO RELEASE TUBE
PUSHING TUBE IN BEFORE
PULLING IT OUT HELPS TO
RELEASE TUBE
FIG. 2
OPERATION OFQUICKCONNECT FITTINGS
OVL-EBP OVL-SBP OVL-SEBP OVL-ESBP
FIG. 3 FIG. 4
23 24 15
14 Regulator Mounting
Bracket
IMPORTANT! INSTALLER PLEASE NOTE.
THE GROUNDING OF ELECTRICALEQUIPMENT SUCHAS TELEPHONE, COMPUTERS, ETC. TO WATER LINES
ISACOMMONPROCEDURE.THISGROUNDING MAYBEINTHE BUILDINGOR MAYOCCURAWAYFROM THE
BUILDING. THIS GROUNDING CAN CAUSE ELECTRICALFEEDBACK INTOAFOUNTAIN, CREATINGAN ELEC-
TROLYSIS WHICH CAUSESAMETALLICTASTE ORAN INCREASE INTHE METALCONTENTOFTHE WATER.
THISCONDITIONISAVOIDABLEBYUSING THE PROPER MATERIALSAS INDICATED.ANY DRAIN FITTINGS
PROVIDEDBYTHE INSTALLER SHOULD BE MADE OF PLASTIC TOELECTRICALLY ISOLATETHE FOUNTAIN
FROMTHEBUILDINGPLUMBINGSYSTEM.
Installer
NOTE: WATER FLOW
DIRECTION
BUILDINGWATER INLET
SERVICESTOP
(NOT FURNISHED)
1/4"O.D.TUBE
WATERINLET
TOCOOLER
3/8"O.D.UNPLATED
COPPERTUBE CONNECT
COLDWATER SUPPLY

97638C (Rev. H - 5/08) PAGE2
OVL-EBP*C, OVL-SBP*C, OVL-SEBP*F, OVL-ESBP*F
OVL- EBP/SBP/SEBP/ESBP COOLER INSTALLATION
1. Fountains using the MPW Mounting Plate refer to Fig's. 6,8,10, or 12 for hanger bracket
location and rough-in dimensions.
NOTE: Review separate installation instructions for details of the MPW Mounting Plate.
Fountains using the Wall Plate Assy. refer to Fig's. 5,7,9, or 11 for rough-in dimensions.
2. Shown dimensions pertain to installation location (framing must support up to 150 lbs. weight
for single fountain and 300 lbs. for dual fountains). These dimensions are required for compliance
withANSI StandardA117.0.
3. Install rough-in plumbing as shown in Fig’s. 5,6,7,8,9,10,11, or 12. Waste line should extend a
minimum of 2" (51mm) thru the back panel. Run supply water inlet line thru back panel.
Install a service stop (not provided). Turn on supply water and flush thoroughly.
4. Installing back panel.
Ftn. w/MPW Mounting Plate: Refer to Fig. 16 for placement of braces onto back panel.
Place the upper edge of the panel above hanger bracket. Slide the panel down until it engages the
hanger bracket. Be sure back panel is firmly engaged before releasing it.
Ftn. w/Wall Plate Assy.: Place the upper edge of the panel above mounting plate on the
wall. Slide the panel down until it engages the hanger. Be sure back panel is firmly engaged
before releasing it.
5. Remove bottom access panel from fountain basin and save the screws.
Ftn. w/MPW Mounting Plate: Install the fountain to the back panel and wall using (4) 5/16 “ x 6”
long threaded rods, washers, and nuts (provided). Tighten securely.
Ftn. w/Wall PlateAssy.: Install the founrain to the back panel and wall using
(4) 5/16" x 3/4" long bolts and washers (provided) thru holes in back panel. Washer used on
bottom two (2) holes only. Tighten securely.
6. Cut waste tube to required length using plumbing hardware and trap (not provided) as a
guide. Install hardware and trap. Tighten securely.
7. Make water supply connections from service stop to the fountain strainer. Insert the
water inlet line into the inlet side of strainer until it reaches a positive stop - about 3/4"
(See Fig. 2). Turn on water supply and check for leaks. Newly installed water supply line
should be insulated after leak check is completed. DO NOT SOLDER TUBES INSERTED
INTO THE STRAINER AS DAMAGE TO THE O-RINGS MAY RESULT.
8. Check stream height from bubbler. Stream height is factory set at 45-50 PSI. If supply
pressure varies greatly from this, adjust the screw on regulator (item 14, on page 1).
Clockwise adjustment will raise stream height and counter-clockwise will lower stream
height. For best adjustment stream height should be approximately 1-1/2" (38mm) above
the bubbler guard. (See Figure 3)
9. Water Valve Mechanism - ADJUSTMENT PROCEDURE:
- Turn adjustment screw (Item 26, page 11) counter-clockwise until water flow from
bubbler starts
- Turn adjustment screw clockwise until water flow stops, then turn an additional
1/2 turn
10. Replace bottom access panel to fountain using the screws provided. Tighten securely.

97638C (Rev. H - 5/08)PAGE3
OVL-EBP*C, OVL-SBP*C, OVL-SEBP*F, OVL-ESBP*F
FIG. 5
LEGEND: A = 1-1/4" O.D. Waste Tube (Trap And Elbow Not Provided) B = 3/8" O.D. Unplated Copper Tube Connect (Water Inlet) C = 1/4" (6mm) DIA. Holes For Mounting Plate To Wall
FINISHED FLOOR
ROUGH-INFOR OVL-EBPWITHWALLPLATEASSY.

97638C (Rev. H - 5/08) PAGE4
OVL-EBP*C, OVL-SBP*C, OVL-SEBP*F, OVL-ESBP*F
ROUGH-INFOROVL-EBPWITHMPW100MOUNTINGPLATE
FIG. 6
43 7/8" 1114mm
HANGER BRACKET "A"
"B"
BACK PANEL
"C"
MPW100
MTG. PLT.
27 1/2" 698mm
28 1/2" 724mm
1/2" 13mm
8" 203mm
16" 406mm
27" 685mm
ADA
REQUIREMENT
7" 179mm
5/8" 16mm
18" 457mm
FINISHED WALL
FINISHED FLOOR
1 7/8" 47mm
8" 203mm
MPW100MTG. PLT. REF. SEPARATEINSTALLATION INSTRUCTIONSFORDETAILS
LEGEND: A = 1-1/4" O.D. Waste Tube (Trap And Elbow Not Provided) B = 3/8" O.D. Unplated Copper Tube Connect (Water Inlet) C = 3/8" (10mm) DIA. Slots For Mounting Hanger Bracket To Wall

97638C (Rev. H - 5/08)PAGE5
OVL-EBP*C, OVL-SBP*C, OVL-SEBP*F, OVL-ESBP*F
LEGEND: A = 1-1/4" O.D. Waste Tube (Trap And Elbow Not Provided) B = 3/8" O.D. Unplated Copper Tube Connect (Water Inlet) C = 1/4" (6mm) DIA. Holes For Mounting Plate To Wall
FIG. 7
FINISHED FLOOR
ROUGH-INFOR OVL-SBPWITHWALLPLATEASSY.

97638C (Rev. H - 5/08) PAGE6
OVL-EBP*C, OVL-SBP*C, OVL-SEBP*F, OVL-ESBP*F
ROUGH-INFOROVL-SBPWITHMPW100MOUNTINGPLATE
FIG. 8
43 7/8" 1114mm
33 5/8" 854mm
34 5/8" 879mm
8" 203mm
1/2" 13mm
MPW100 MTG. PLT.
HANGER BRACKET
BACK PANEL
"C"
"A"
"B"
16" 406mm
FINISHED FLOOR
33" 837mm
7" 179mm
5/8" 16mm
13 5/16" 338mm
FINISHED WALL
1 7/8" 47mm
8" 203mm
MPW100MTG. PLT. REF. SEPARATEINSTALLATION INSTRUCTIONSFORDETAILS
LEGEND: A = 1-1/4" O.D. Waste Tube (Trap And Elbow Not Provided) B = 3/8" O.D. Unplated Copper Tube Connect (Water Inlet) C = 3/8" (10mm) DIA. Slots For Mounting Hanger Bracket To Wall

97638C (Rev. H - 5/08)PAGE7
OVL-EBP*C, OVL-SBP*C, OVL-SEBP*F, OVL-ESBP*F
FIG. 9
LEGEND: A = 1-1/4" O.D. Waste Tube (Trap And Elbow Not Provided) B = 3/8" O.D. Unplated Copper Tube Connect (Water Inlet) C = 1/4" DIA. (6mm) Holes For Mounting Plate To Wall
FINISHED FLOOR
ROUGH-INFOR OVL-SEBPWITHWALLPLATEASSY.

97638C (Rev. H - 5/08) PAGE8
OVL-EBP*C, OVL-SBP*C, OVL-SEBP*F, OVL-ESBP*F
ROUGH-INFOROVL-SEBPWITHMPW200MOUNTINGPLATE
FIG. 10
18" 457mm 5/8"
16mm
13 5/16" 338mm
FINISHED WALL
FINISHED FLOOR
27" 687mm
ADA
REQUIREMENT
7" 179mm
43 7/8" 1114mm
3 1/4" 82mm
16" 406mm
32" 813mm
6 5/8" 168mm 18 3/4"
476mm
1/2" 13mm 1/2"
13mm
"A"
"A"
"B"
"B"
27 1/2" 698mm
28 1/2" 724mm
33 5/8" 854mm
34 5/8" 879mm 33"
838mm
"C" HANGER BRACKET
BACK PANEL
MPW200
MTG. PLT.
MPW200MTG. PLT. REF. SEPARATEINSTALLATION INSTRUCTIONSFORDETAILS
LEGEND: A = 1-1/4" O.D. Waste Tube (Trap And Elbow Not Provided) B = 3/8" O.D. Unplated Copper Tube Connect (Water Inlet) C = 3/8" (10mm) DIA. Slots For Mounting Hanger Bracket To Wall

97638C (Rev. H - 5/08)PAGE9
OVL-EBP*C, OVL-SBP*C, OVL-SEBP*F, OVL-ESBP*F
FIG. 11
LEGEND: A = 1-1/4" O.D. Waste Tube (Trap And Elbow Not Provided) B = 3/8" O.D. Unplated Copper Tube Connect (Water Inlet) C = 1/4" DIA. (6mm) Holes For Mounting Plate To Wall
FINISHED FLOOR
ROUGH-INFOR OVL-ESBPWITHWALLPLATEASSY.

97638C (Rev. H - 5/08) PAGE10
OVL-EBP*C, OVL-SBP*C, OVL-SEBP*F, OVL-ESBP*F
ROUGH-INFOROVL-ESBPWITHMPW200MOUNTINGPLATE
FIG. 12
3 1/4" 82mm
16" 406mm
32" 813mm
27 1/2" 698mm
28 1/2" 724mm 33 5/8"
854mm 34 5/8"
879mm
1/2" 13mm 1/2"
13mm HANGER BRACKET
"C"
"B" "B"
"A"
"A"
BACK PANEL
FINISHED FLOOR
FINISHED WALL
18" 457mm
43 7/8" 1114mm
5/8" 16mm
13 5/16" 338mm
27" 687mm
ADA
REQUIREMENT
7" 179mm
33" 840mm
6 5/8" 168mm 18 3/4"
476mm
MPW200
MTG. PLT. MPW200MTG. PLT.
REF. SEPARATEINSTALLATION INSTRUCTIONSFORDETAILS
LEGEND: A = 1-1/4" O.D. Waste Tube (Trap And Elbow Not Provided) B = 3/8" O.D. Unplated Copper Tube Connect (Water Inlet) C = 3/8" (10mm) DIA. Slots For Mounting Hanger Bracket To Wall

97638C (Rev. H - 5/08)PAGE11
OVL-EBP*C, OVL-SBP*C, OVL-SEBP*F, OVL-ESBP*F
FIG. 14
FIG. 15
19
2
20
29
26
29
26
27
30
22 31
25Stream Height Adjustment
18 5
10
9
12
13
6
7
8
11
1See Fig. 15
21
See Fig. 4
3, 4
16
17
See Fig. 14
FIG. 13
PUSH BAR MECHANISM
REGULATOR MOUNTING MECHANISM
Installing Back Panel: When install-
ing back panel assy. (Item 34) with
MPW (Mounting Plate), attach channel
bracesas shownabove.Remove the
protectivebacking fromthe tape
installed on the braces. Line up the
correspondingholes inthebracesand
back panel and press firmly in place.
FIG. 16
34

97638C (Rev. H - 5/08) PAGE12
OVL-EBP*C, OVL-SBP*C, OVL-SEBP*F, OVL-ESBP*F
DESCRIPTION
26990C
26988C
55836C
55991C
51546C
45396C
100322740560
160270508640
45400C
101570540560
51575C
110346220550
101637451550
161637308640
45398C
45683C
45682C
100023340560
161570808550
61314C
50986C
27006C
27342C
27000C
27344C
70861C
55840C
55839C
27002C
27338C
27004C
27340C
28328C
15005C
40045C
27008C
70856C
70854C
50198C
51667C
28327C
28326C
22797C
27886C
22799C
27888C
26958C
27890C
22795C
27892C
28120C
28121C
28168C
28169C
28838C
28839C
28811C
28821C
55996C
56159C
56092C
75541C
111577243890
27089C
27090C
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
NS
NS
NS
NS
NS
NS
NS
PARTNO.
BottomCover(OVL-S)
BottomCover(OVL-E)
PushArmActuator
PushArmActuator- AG
Bubbler
Bubbler-AG
BubblerGasket
StrainerPlate
StrainerPlate-AG
DrainGasket
PackingRing
DrainNut
FrictionRing
DrainPlug
DrainPlug-AG
WasteElbow(OVL-E)
WasteElbow(OVL-S)
WasteTubeGasket
SlipNut
Regulator
RegulatorHolder
Basin
Basin-AG
BasinLiner
BasinLiner-AG
Screw#10-24x 2
Top Plate-Actuator
BottomPlate- Actuator
Armw/Weldnuts(OVL-E)
Carrier Arm - AG (OVL-E)
Armw/Weldnuts(OVL-S)
Carrier Arm - AG (OVL-S)
RegulatorMountingBracket
Nut-Retaining
Nut Hex - UNPLTD
ReactionBracket
Screw#10-24x.38 PHMS
Rod-Pivot
BushingSnap
Bumper-Reg.ValveAssy
Arm -Reg.Activating
Arm-Reg. Adjustment
BackPanel (OVL-EBP)
BackPanel (OVL-EBP)(AG)
BackPanel (OVL-SBP)
BackPanel (OVL-SBP)(AG)
BackPanel (OVL-SEBP)
BackPanel (OVL-SEBP)(AG)
BackPanel (OVL-ESBP)
BackPanel (OVL-ESBP)(AG)
WallPlateAssembly -OVL-SBP
WallPlateAssembly -OVL-SEBP
WallPlateAssembly -OVL-EBP
WallPlateAssembly -OVL-ESBP
BackPanel Assy.(OVL-EBP)
BackPanel Assy.(OVL-SBP)
BackPanel Assy. (OVL-SEBP)
BackPanel Assy. (OVL-ESBP)
Strainer
BubblerNippleAssy
Tube- Poly (CutTo Length)
Washer-Flat.339/.359IDSteel
Screw-Mach.5/16-18 x3/4
HangerBracket(OVL-EBP/SBP)
HangerBracket(OVL-SEBP/ESBP)
ITEM NO.
PARTSLIST
FOR PARTS CONTACT YOUR LOCAL DISTRIBUTOR OR VISIT OUR WEBSITE WWW.HALSEYTAYLOR.COM
2222CAMDENCOURT
OAKBROOK, IL60523
630.574.3500
PRINTEDINU.S.A.
TROUBLE SHOOTING AND MAINTENANCE
Orifice Assy: Mineral deposits on orifice can cause water flow to spurt or
not regulate. Mineral deposits may be removed from the orifice with a
small round file or small diameter wire.
CAUTION: DO NOT file or cut orifice material.
Stream Regulator: If orifice is clean, regulate flow as in
“STREAM HEIGHT ADJUSTMENT” instructions on pg 2. If replacement
is necessary, see parts list for correct regulator part number.
Actuation of Quick Connect Water Fittings: Fountain is provided with
lead-free connectors which utilize an o-ring water seal. To remove
tubing from the fitting, relieve water pressure, push in on the gray collar
while pulling on the tubing.(see Fig.2) To insert tubing, push tube
straight into fitting until it reaches a positive stop, approximately 3/4".
CAUTION: To preserve the quality and keep this AZTEC GOLD finish clean
and spot free, clean this surface with only mild detergent or window
cleaner and polish with a soft cloth. DO NOT use any abrasive cleaners
or harsh chemicals. They WILL damage the finish!
32
SEEPUSHBARMECHANISM
(ONPAGE 11)
SEEPUSHBARMECHANISM
(ONPAGE 11)
SEEDETAIL
(ONPAGE 11)
SEEDETAIL
(ONPAGE 11)
32
33
33