halstrup-walcher PS*3**PL series User manual

Instruction Manual PSx3xxPL
1
Instruction Manual
PSx3xxPL
halstrup-walcher GmbH
Stegener Straße 10
D-79199 Kirchzarten
Tel.: [phone]
Fax: [phone]
E-Mail: [e-mail]
Internet: www.halstrup-walcher.com
Document 7100.005424 07/2017

Instruction Manual PSx3xxPL
2
Table of Contents
1Safety precautions....................................................................................................................4
1.1 Appropriate use..................................................................................................................4
1.2 Shipping, assembly, electrical connections and start-up.....................................................4
1.3 Troubleshooting, maintenance, repairs, disposal................................................................4
1.4 Symbols .............................................................................................................................5
2Device Description ...................................................................................................................5
2.1 Features.............................................................................................................................5
2.2 Installation..........................................................................................................................5
2.3 Pin assignment...................................................................................................................6
2.4 Setting the device address .................................................................................................7
2.5 LEDs..................................................................................................................................7
2.6 Start-up..............................................................................................................................8
2.7 Powerlink interface.............................................................................................................9
3Specials .................................................................................................................................22
4Technical Data.......................................................................................................................31

Instruction Manual PSx3xxPL
3
Purpose of instruction manual
This instruction manual describes the features of the PSx3xxPL positioning system
and provides guidelines for its use.
Improper use of these devices or failure to follow these instructions may cause injury
or equipment damage. Every person who uses the devices must therefore read the
manual and understand the possible risks. The instruction manual, and in particular
the safety precautions contained therein, must be followed carefully. Contact the
manufacturer if you do not understand any part of this instruction manual.
Handle this manual with care:
It must be readily available throughout the lifecycle of the devices.
It must be provided to any individuals who assume responsibility for operating the
device at a later date.
It must include any supplementary materials provided by the manufacturer.
The manufacturer reserves the right to continue developing this device model without
documenting such development in each individual case. The manufacturer will be
happy to determine whether this manual is up-to-date.
Conformity
This device is state of the art. It complies with the legal requirements of EC directives.
This is shown by the CE mark.
© 2015, 2016, 2017
The manufacturer owns the copyright to this instruction manual. It contains technical
data, instructions and drawings detailing the devices’ features and how to use them. It
must not be copied either wholly or in part or made available to third parties.

Instruction Manual PSx3xxPL
4
1 Safety precautions
1.1 Appropriate use
Positioning systems are especially suitable for automatically setting tools, stops or
spindles for wood-processing equipment, packing lines, printing equipment, filling
units and other types of special machines.
PSx3xxPL positioning systems are not stand-alone devices and may only be
used if coupled to another machine.
Always observe the operating requirements –particularly the permissible supply
voltage –indicated on the rating plate and in the “Technical data” section of this
manual.
The device may only be handled as indicated in this manual. Modifications to the
device are prohibited. The manufacturer is not liable for damages caused by improper
use or failure to follow these instructions. Violations of this type render all warranty
claims null and void.
1.2 Shipping, assembly, electrical connections and start-up
Assembly and the electrical connections should only be handled by professionals.
They should be given proper training and be authorised by the operator of the facility.
The device may only be operated by appropriately trained individuals who have been
authorized by the operator of the facility.
Specific safety precautions are given in individual sections of this manual.
1.3 Troubleshooting, maintenance, repairs, disposal
The individual responsible for the electrical connections must be notified immediately
if the device is damaged or if errors occur.
This individual must take the device out of service until the error has been corrected
and ensure that it cannot be used unintentionally.
This device requires no maintenance.
Only the manufacturer may perform repairs that require the housing to be opened.
The electronic components of the device contain environmentally hazardous
materials and materials that can be reused. The device must therefore be sent to a
recycling plant when you no longer wish to use it. The environment codes of your
particular country must be complied with.

Instruction Manual PSx3xxPL
5
1.4 Symbols
The symbols given below are used throughout this manual to indicate instances when
improper operation could result in the following hazards:
WARNING! This warns you of a potential hazard that could lead to bodily injury up
to and including death if the corresponding instructions are not followed.
CAUTION! This warns you of a potential hazard that could lead to significant
property damage if corresponding instructions are not followed.
INFORMATION! This indicates that the corresponding information is important
for operating the device properly.
2 Device Description
2.1 Features
The PSx3xxPL positioning system, an intelligent, compact, complete solution for
positioning auxiliary and positioning axes, consists of an EC motor, gear power
amplifier, control electronics, absolute measuring system and EtherCAT interface.
The integrated absolute measuring system eliminates the need for a time-consuming
reference run. Connecting to a bus system simplifies the wiring. A hollow shaft with
adjustable collar makes assembly quite simple. The positioning system is especially
suitable for automatically setting tools, stops or spindles for wood-processing
equipment, packing lines, printing equipment, filling units and other types of special
machines.
PSx3xxPL positioning systems convert a digital positioning signal into an angle of
rotation.
If the device names are given without the diameter of the output shaft (-8, -
14), the relevant information is valid for all offered output shafts (applies
throughout the document).
‘x’ in the device name stands for a number in the range 0..9. ‘xx’ in the
device name stands for a number in the range 10..999.
2.2 Installation
Hollow shaft:
The PSx3xxPL is mounted onto the machine by sliding the hollow shaft of the
positioning gear onto the axis to be driven and then securing it with an adjustable
collar (recommended axis diameter 8h9 resp. 14h9; wrench torque for screw: 1.5Nm).
The adjustable collar should be tightened only just to the point where it can no longer
rotate freely.
Securing the pin under the hollow shaft into an appropriate bore will prevent further
rotation (if required, consider drawing on the website).

Instruction Manual PSx3xxPL
6
Solid shaft:
The PSx3xxPL is mounted on the machine by fixing the solid shaft with coupling and
intermediate flange to the axis of the machine.
Never apply force to the housing cover, e.g., for supporting weight.
Driving the PSx3xxPL rearward is prohibited (e.g. it’s not allowed to turn
the output shaft by an external force).
2.3 Pin assignment
For the supply voltage either a Binder series 713/763 (A-coded) round, 5-pin plug for
PSE and PSS devices or a 5-pin Harting plug with protective sleeve (HAN4A) for the
PSE34xx devices is located in the housing cover of the PSx3xxPL.
Two round 4-pin sockets, Binder series 825 (D-coded) are provided for connection to
the bus.
Supply voltage connector::
Round socket for bus:
Round plugr
Harting plug
(extrenal top view)
(extrenal top view)
(extrenal top view)
1+24V motor
2GND motor
3 +24V control unit
4 GND control unit
5 housing/pressure balance
1 TD+ (WH/GN, white/green)
2 RD+ (WH/OG, white/orange)
3 TD- (GN, green)
4 RD (OG, orange)
Due to the use of 4-pin sockets,
only four-wire cables should be
used.
To prevent the ingression of fluids into the PSW-housing during cooldown,
use a special cable with an airtube for pressure balancing of your PSW
Electrical grounding:
Next to the connecting plugs there is a M4 stud bolt. It is recommended to connect
the positioning system with a cable as short as possible to the machine base. The
minimum wire cross section therefor is 1.5mm².

Instruction Manual PSx3xxPL
7
2.4 Setting the device address
Removing the protective cap provides access to two rotary switches for setting the
device address at the bus.
The rotary switches indicate the tens and ones places of the address selected.
The delivery setting is 00, e.g. before the first start-up a valid address has to be
set.
2.5 LEDs
The following LEDs are located under the transparent sealing plug:
P1/P2: green Link/Act LEDs for ports 1 and 2
BS/BE: Powerlink STATUS and ERROR LEDs (green/red; see Powerlink spec.)
V_Motor: The LED is illuminated yellow when power is available to the motor.
Switch configurations:
PSx30xPL, PSx31xPL-8, PSx31xPL-14, PSx33xPL
PSx32xPL, PSE31xxPL,
PSE34xxPL
Meaning of the LEDs:
1) Each of the ports (P1/P2) has an associated green LED for the “Link” and the
“Activity” state.
For each port the following states are possible:
- Off no connection
- On connection; data transmission inactive
- Flickering with 10 Hz connection; data transmission active
2) The green Powerlink LED “Bus Status” (BS) signalizes the CN cycle state.
- Off NOT_ACTIVE
- Flickering with 10 Hz BASIC_ETHERNET

Instruction Manual PSx3xxPL
8
- Single flashing with 0.8 Hz PRE-OPERATIONAL_1
- Double flashing with 0.6 Hz PRE-OPERATIONAL_2
- Triple flashing with 0.5 Hz READY_TO_OPERATE
- Flashing with 2.5Hz STOPPED
- On OPERATIONAL
3) The red Powerlink LED “Bus Error” (BE) signalizes an error:
- Off no error
- On error
4) The yellow LED “Motor” indicates the supply voltage for the motor:
- Off supply voltage for motor too low or too high
- On supply voltage for motor ok
2.6 Start-up
After the supply voltage has been hooked up, a positioning or manual run can begin
immediately:
a) Positioning run
- To be able to control the drive with the help of PDOs, it has to be switched to the CN
cycle state “operational”.
- Transfer target value:
- PDO with control word = 0x14 and desired target value
OR
- PDO with control word = 0x10 and target value in SDO #2001
Drive begins run
- Abort run by resetting the release bit:
- PDO with control word = 0x00
OR
- SDO #2024 with value 0x00 (if pre-operational)
- If a new target value is transferred during a positioning run, the device will
immediately proceed to the new target. There will be no interruption if the direction of
rotation does not need to be altered.
- If a manual run is transmitted during a positioning run, the positioning run will be
aborted (speed will be reduced to that of a manual run) and the device proceeds with
the manual run.
The following sequence of steps is also possible:
Starting situation: release has not been set
- Transfer target value:
- PDO with control word = 0x04 and desired target value
OR
- PDO with control word = 0x00 and target value in SDO #2001
- Set release:
- PDO with control word = 0x10
OR
- SDO #2024 with value 0x10 (if pre-operational)
Drive begins run

Instruction Manual PSx3xxPL
9
Where applicable, positioning runs involve a “loop run” which causes the
target position to be reached from a predefined direction. The direction and
the length of the loop run can be set to the desired value with SDO #201F
(“length of loop”) before the run. With SDO #201F the loop run might also
be disabled.
Setting of control word and target value with the help of SDOs is only
possible in the CN cycle state “pre-operational”.
b) Manual run
- Start manual run (transmit PDO with control word = 0x11 resp. 0x12 or, if pre-
operational, transmit SDO #2024 with value 0x11 resp. 0x12): device begins to run
- End manual run by clearing the manual run command (transmit PDO with control
word = 0x10 or, if pre-operational, transmit SDO #2024 with value 0x10) or by
deasserting release (transmit PDO with control word = 0x00 or, if pre-operational,
transmit SDO #2024 with value 0x00).
- Transferring a target value during a manual run will end the manual run and the
device will immediately move on to the transmitted position (PDO with control word =
0x14 and desired target value). If pre-operational, target value in SDO #2001. The
drive then automatically deasserts the manual run bits in the control word (bits 0 and
1).
Underwater usage of the PSW is not allowed.
2.7 Powerlink interface
The Powerlink interface is realized according the EPSG standard 301, version 1.2.0:
One send and receive SDO per device
One asynchron send and receive PDO, active by default

Instruction Manual PSx3xxPL
10
a) Table of entries implemented from object dictionary
Name
Index
number
Function
Range of
value
Back
up
Delivery
State
R/W
Device Type
1000
returns a “0” when read
32 bit
0
R
Error
Register
1001
Error register according CiA DS 301
8 bit
R
Error History
1003
Sub-Index 0: quantitiy of current entrys
sub 1 … 254: error entrys (latest entry in
sub 1)
8 bit
160 bit
no
0
R/W
R
Manufacturer
Software
Version
100A
denotes the software of the Powerlink
drives; when being read the string
“PSx3xxIE/PL” is given back
R
Identity
1018
sub index 0: quantity of indexes (= 4)
sub 1: Vendor-ID (= 0x000002D8)
sub 2: Product code
sub 3: Revision number (= 0x00010000)
sub 4: Serial number
8 bit
32 bit
32 bit
32 bit
32 bit
4
R
R
R
R
R
Receive
PDO 1
communi-
cation
parameter
1400
sub index 0: quantity of indexes (= 2)
sub 1: Node ID (= 0)
sub 2: Mapping Version (= 0)
8 bit
0...0
8 bit
8 bit
no
R
R/W
R
Receive
PDO 1
mapping
1600
sub index 0: quantity of indexes (= 2)
sub 1: 0x0010000000002024
sub 2: 0x0020001000002001
2...2
8 bit
64 bit
64 bit
no
2
R/W
R
R
Transmit
PDO 1
communi-
cation
parameter
1800
sub index 0: quantity of indexes (= 2)
sub 1: Node ID (= 0)
sub 2: Mapping Version (= 0)
8 bit
0...0
8 bit
8 bit
no
R
R/W
R
Transmit
PDO 1
mapping
1A00
sub index 0: quantity of indexes (= 3)
sub 1: 0x0010000000002025
sub 2: 0x0010001000002030
sub 3: 0x0020002000002003
3...3
8 bit
64 bit
64 bit
64 bit
no
3
R/W
R
R
R

Instruction Manual PSx3xxPL
11
Name
Index
number
Function
Range of
value
Back
up
Delivery
State
R/W
general
purpose
register
2000
0...10
10 general purpose registers
sub index 0: quantity of indexes (= 10)
sub 1..10: general purpose registers
8 bit
32 bit
yes
10
0
R
R/W
target value
2001
target position to be achieved
value in 1/100 mm (for a 4mm spindle and
default settings of numerator, #2010 and
denominator, #2011)
31 bit
no
0
R/W
actual value
2003
current actual position
value in 1/100 mm (for a 4mm spindle and
default settings of numerator #2010 and
denominator #2011)
Writing onto this index number causes the
current position to be “referenced” onto
the transferred value.
Changes only possible when at standstill
31 bit
no
R/W
referencing
value
2004
correction factor for the target, actual and
limit switch values
Changes only possible when at standstill
31 bit
yes
0
R/W
drag error
2005
maximum drag error before the ‘drag
error’ bit is set.
value in 1/100 mm (for a 4mm spindle and
default settings of numerator and
denominator)
0...1000
16 bit
yes
0
R/W
positioning
window
2006
permissible difference between target and
actual values for “position reached” bit
value in 1/100 mm (for a 4mm spindle and
default settings of numerator and
denominator)
The maximum value that can be set
changes according to the same factor as
the resolution.
Changes only possible when at standstill
1...100
16 bit
yes
2
R/W
position
scaling,
numerator
2010
These values can be used to set a
desired user resolution to the drive.
For a numerator factor of 400, the
denominator factor holds the spindle pitch
per resolution
e.g.: spindle pitch 1.5 mm with resolution
1/100 mm:
numerator = 400, denominator = 150
Changes only possible when at standstill
1...10000
16 bit
yes
400
R/W
position
scaling,
denominator
2011
1...10000
16 bit
yes
400
R/W
target rpm
posi
2012
value in rpm
maximum rpm to be used for positioning
runs
see table
16 bit
yes
see
table
R/W
target rpm
hand
2013
value in rpm
maximum rpm to be used for manual runs
see table
16 bit
yes
see
table
R/W
maximum
torque
2014
Applies after completion of start phase
(during start phase the value #2018
applies); value in cNm
see table
16 bit
yes
see
table
R/W

Instruction Manual PSx3xxPL
12
Name
Index
number
Function
Range of
value
Back
up
Delivery
State
R/W
upper limit
2016
maximum permitted target position
minimum value:
upper mapping end - 253 revolutions
maximum value:
upper mapping end - 3 revolutions
Changes only possible when at standstill
31 bit
yes
101200
R/W
lower limit
2017
minimum permitted target position
minimum value:
upper mapping end - 253 revolutions
maximum value:
upper mapping end - 3 revolutions
Changes only possible when at standstill
31 bit
yes
1200
R/W
maximum
start-up
torque
2018
value in cNm
see table
16 bit
yes
see
table
R/W
time period
for start-up
torque
2019
Time period at the beginning of a move in
which the maximum start-up torque
applies
value in msec
10...1000
16 bit
yes
200
R/W
rpm limit for
aborting run
201A
value in % of the target rpm
30...90
16 bit
yes
30
R/W
time elapsed
until speed
falls below
rpm limit for
aborting run
201B
value in msec
50...500
16 bit
yes
200
R/W
acceleration
201C
value in rpm per sec.
see table
16 bit
yes
see
table
R/W
deceleration
201D
value in rpm per sec.
see table
16 bit
yes
see
table
R/W
length of loop
201F
minimum number of increments which the
drive moves in a pre-defined direction
when approaching a target position
value in increments (value = 0 no loop)
Changes only possible when at standstill
-1…1
rotation
31 bit
yes
-250
R/W
control word
2024
Bit 0: manual run to larger values
Bit 1: manual run to smaller values
Bit 2: transfer target value (When sending
the target values with the help of PDOs,
positioning will only take place if this bit is
set.)
Bit 4: release: The axle will only run if this
bit is set.
All other bits must be set to 0!
16 bit
no
0
R/W

Instruction Manual PSx3xxPL
13
Name
Index
number
Function
Range of
value
Back
up
Delivery
State
R/W
status word
2025
Bit 0: target position reached
Bit 1: drag error
Bit 2: reserved
Bit 3: reserved
Bit 4: motor power present
Bit 5: positioning run aborted
Bit 6: drive is running
Bit 7: temperature exceeded
Bit 8: movement opposite loop direction
Bit 9: error
Bit 10: positioning error (block)
Bit 11: manual displacement
Bit 12: incorrect target value
Bit 13: motor power was missing
Bit 14: positive range limit
Bit 15: negative range limit
0..FFFFh
16 bit
R
upper
mapping end
2028
definition of the positioning range relative
to the absolute measuring system
permissible values:
(actual position value + 3 revolutions …
(actual position value + 253 revolutions)
Changes only possible when at standstill
31 bit
yes
102400
R/W
maximum
holding
torque
202B
maximum holding torque at standstill in
cNm
see table
16 bit
yes
see
table
R/W
direction of
rotation
202C
0: clockwise with larger values
(if looking at the output shaft)
1: counter clockwise with larger values
Changes only possible when at standstill
0 oder 1
16 bit
yes
0
R/W
idle period
202E
idle period in msec when reversing the
direction of rotation
10...
10000
16 bit
yes
10
R/W
actual rpm
2030
value in rpm
15 bit
R
maximum
torque
2031
maximum torque occurring during the
most recent run (start phase, during which
the maximum start-up torque applies, see
SDOs #2018/2019, and the phase when
the drive is braking down, are not
considered)
value in cNm
16 bit
R
actual torque
2033
value in cNm
16 bit
R
U control
203A
current supply voltage for control unit
given in increments of 0.1 V
16 bit
R
U motor
203B
current supply voltage for motor given in
increments of 0.1 V
16 bit
R

Instruction Manual PSx3xxPL
14
Name
Index
number
Function
Range of
value
Back
up
Delivery
State
R/W
Umot limit
203C
voltage limit for bit 4 (‘motor power
present’); given in increments of 0.1 V
Beginning a positioning run or a manual
run is only possible if the supply voltage
for the motor is higher than the value of
this SDO. During the run the voltage
might fall down to 17.5V.
180…
240
16 bit
yes
185
R/W
Umot filter
203D
average time for measuring motor supply
voltage; value in msec
100…
1000
16 bit
yes
100
R/W
temperature
limit
203E
upper temperature limit in °C
10...70
16 bit
yes
70
R/W
device
temperature
203F
internal device temperature in °C
16 bit
R
production
date
2040
year and week of manufacturing
(given as an integer)
YYWW
16 bit
R
serial number
2041
serial device number
0…
65535
16 bit
R
maximum
holding
torque at end
of run
2042
value in cNm
see table
16 bit
yes
see
table
R/W
duration of
maximum
holding
torque at end
of run
2043
time period at end of run, in which the
‘maximum holding torque at end of run’
applies (value in msec)
0…
1000
16 bit
yes
200
R/W
waiting time
for brake
(end of run)
2045
time period after the end of run, in which
the brake stays released (value in msec)
0...3000
16 bit
yes
1000
R/W
drag error
correction
2046
maximum modification of the target speed
for drag error correction
Changes only possible when at standstill
0…10
16 bit
yes
4
R/W
readjustment
2047
readjustment at standstill
0 Off; 1 On
0…1
8 bit
yes
0
R/W

Instruction Manual PSx3xxPL
15
Name
Index
number
Function
Range of
value
Back
up
Delivery
State
R/W
configuration
for
connection
timeout
2049
Bits 1-0: configuration for connection
timeout (if a connection has been
established and lost)
0x00: continue moving (drive will continue
moving to the actual target position)
0x01: drive will abort any positioning
0x02: drive will move to a save position
which is defined by SDO #204A
0x03: reserved
Bits 3-2: configuration of save position run
when no connection is being established
after a certain time at power-up
0x00: no save position run at power-up
0x01: save position run after 15 sec
0x02: save position run after 30 sec
0x03: save position run after 60 sec
16 bit
yes
1
R/W
save position
for
connection
timeout
204A
drive will move to this position if
- a connection loss to the master has
been detected and bits 1-0 of SDO #2049
are set to 0x02
- no connection is being established after
a certain time at power-up and bits 3-2 of
SDO #2049 are being set appropriate
31 bit
yes
0
R/W
repetition
time for save
position run
204B
drive will start another save position run if
the last save position run was not
successful (e.g. because of undervoltage,
positioning error (block) or
overtemperature)
value in sec; 0 no repetition
16 bit
yes
0
R/W
device model
204D
device model within the PSx drive series
as string (e.g. “PSE312-8-PL-0-0”)
R
version
204E
software version number
16 bit
R

Instruction Manual PSx3xxPL
16
Name
Index
number
Function
Range of
value
Back
up
Delivery
State
R/W
delivery state
204F
writing “-2”:
sets the values of all parameters to the
values which are saved last by the user,
without saving the parameters in the
EEPROM
writing “-1”:
sets the values of all parameters to the
delivery state, without saving the
parameters in the EEPROM
writing “1”:
saves all parameters in the EEPROM
reading directly after boot:
0 content of memory correct
≠ 0 content of memory incorrect
reading after saving:
0 saving finished successfully
≠0 saving is still in progress or is
finished incorrectly (the time for saving is
up to 200 msec)
Changes only possible when at standstill
-2, -1
oder 1
(writing)
0..2
(reading)
15 bit
no
R/W

Instruction Manual PSx3xxPL
17
Table of rated speed and torque values for various models of gears
device model PSE and
PSS
301-x
311-x
302-x
312-x
305-x
315-8
322
332
325
335
328-14
Name
Index
number
Range of value
Delivery State
target rpm posi
2012
15...230
230
10...150
150
3...70
70
20...200
170
10...100
85
5…45
45
target rpm hand
2013
15...230
80
10...150
50
3...70
20
20...200
80
10...100
40
5…45
22
acceleration
201C
97...600
600
50...400
400
23...130
130
97...525
525
50...260
260
22…100
100
deceleration
201D
97...600
600
50...400
400
23...130
130
97...525
525
50...260
260
22…100
100
maximum torque
2014
2...125
100
10...250
200
50...600
500
10...250
200
20...500
400
80...960
800
maximum start-
up torque
2018
2...125
125
10...250
250
50...600
600
10...250
250
20...500
500
80...960
960
maximum
holding torque
202B
0...90
30
0...150
50
0...300
100
0...100
35
0...200
70
0...450
150
maximum
holding torque at
end of run
2042
0...180
60
0...300
100
0...600
200
0...200
70
0...400
140
0...700
300
device model PSW
301-x
311-x
302-x
312-x
305-x
315-8
322-14
332-14
325-14
335-14
328-14
Name
Index
number
Range of value
Delivery State
target rpm posi
2012
15...180
180
10...125
125
3...60
60
20...150
125
10...80
60
5…35
35
target rpm hand
2013
15...180
80
10...125
50
3...60
20
20...150
80
10...80
40
5…35
22
acceleration
201C
97...600
600
50...400
400
23...130
130
97...525
525
50...260
260
22…100
100
deceleration
201D
97...600
600
50...400
400
23...130
130
97...525
525
50...260
260
22…100
100
maximum torque
2014
2...125
100
10...250
200
50...600
500
10...250
200
20...500
400
80...960
800
maximum start-
up torque
2018
2...125
125
10...250
250
50...600
600
10...250
250
20...500
500
80...960
960
maximum
holding torque
202B
0...90
30
0...150
50
0...300
100
0...100
35
0...200
70
0...450
150
maximum
holding torque at
end of run
2042
0...180
60
0...300
100
0...600
200
0...200
70
0...400
140
0...700
300

Instruction Manual PSx3xxPL
18
device model PSE
3110
3125
3210-x
3310-x
3218
Name
Index
number
Range of value
Delivery State
target rpm posi
2012
1…30
30
1…12
12
5...45
38
3...30
28
target rpm hand
2013
1…30
12
1…12
5
5...45
15
3...30
10
acceleration
201C
9…50
50
4…20
20
20...117
117
11...70
70
deceleration
201D
9…50
50
4…20
20
20...117
117
11...70
70
maximum torque
2014
100...1200
1000
250...3000
2500
100...1200
1200
180...2200
2200
maximum start-up
torque
2018
100...1200
1200
250...3000
3000
100...1200
1000
180...2200
1800
maximum holding
torque
202B
0...600
200
0...1250
450
0...1000
350
0...1800
600
maximum holding
torque at end of
run
2042
0...1200
400
0...2500
900
0...500
175
0...900
300
device model PSE
3325
3410
3418
Name
Index
number
Range of value
Delivery State
target rpm posi
2012
2...18
15
10...100
100
10...90
90
target rpm hand
2013
2...18
6
10...100
40
10...90
30
acceleration
201C
8...45
45
20...350
350
10...315
315
deceleration
201D
8...45
45
20...350
350
10...315
315
maximum torque
2014
250...3000
3000
100...1200
1000
500...2000
1800
maximum start-up
torque
2018
250...3000
2500
100...1200
1200
500...2000
2000
maximum holding
torque
202B
0...2500
900
0...300
200
0...450
300
maximum holding
torque at end of
run
2042
0...1250
450
0...600
400
0...900
600

Instruction Manual PSx3xxPL
19
b) PDO definition
1) Receive PDO (from the perspective of the PSx3xxPL)
Assignment (cannot be modified):
Bit
Byte
Description
corresponding SDO index number
0-15
0,1
control word
2024h
16-47
2-5
target value
2001h
2) Transmit PDO (from the perspective of the PSx3xxPL)
Assignment (cannot be modified):
Bit
Byte
Description
corresponding SDO index number
0-15
0,1
status
2025h
16-31
2,3
current rpm
2030h
32-63
4-7
actual value
2003h
c) Detailed description of the status bits
Bit 0: target position reached
This bit is set:
- when a transferred target position has been reached successfully (not at the
end of a manual run, elsewise the target position is the same as the
applicable limit switch)
- after manual displacement while at standstill, when the actual position is
within the positioning window again
This bit is reset:
- after transferring a target position if the difference from the actual value is
larger than the positioning window (SDO #2006)
- by a manual run
- if an invalid target value has been transferred
- if rotated manually when on standstill
Bit 1: drag error
This bit is set:
- if during a run (except in the braking phase) the difference between actual
target position and actual position exceeds the value which has been set with
SDO #2005
This bit is reset:
- with each new run command
Bit 2: reserved
Bit 3: reserved
Bit 4: motor power present
This bit is set:
- if the supply voltage to the motor is above the Umot limit (SDO #203C) and
below 30V
This bit is reset:
- if the supply voltage to the motor is below the Umot limit or above 30V

Instruction Manual PSx3xxPL
20
Bit 5: positioning run aborted
This bit is set:
- if a positioning run is aborted because release in the control word has been
withdrawn or because of an invalid bit combination in the control word
This bit is reset:
- with each new run command
Bit 6: drive is running
This bit is set:
- when the drive is rotating
This bit is reset:
- when the drive is on standstill
Bit 7: temperature exceeded
This bit is set:
- if the internal device temperature device exceeds the limit value (SDO
#203E)
This bit is reset:
- if the internal device temperature falls below the limit value by 5°C
Bit 8: movement opposite loop direction
This bit is set:
- after power-up or a reset (a lash in a driven spindle which might be present is
not yet eliminated)
- when commanding a positioning run or a manual run in opposite of the loop
direction
- when commanding a positioning run or a manual run, when no loop is
configured (SDO #201F is zero)
This bit is reset:
- when a transferred target position has been reached successfully in the loop
direction (not after a manual run)
Bit 9: error
This bit is set:
- if an internal problem is detected when calculating a position
No run commands can be executed when the error bit is set!
This bit is reset:
- only possible by resetting or power-cycle the drive
Bit 10: positioning error (block)
This bit is set:
- if a positioning run or a manual run is aborted because the device is
overloaded (block, extreme difficulty while running)
This bit is reset:
- with each new run command
Bit 11: manual displacement
This bit is set:
- if, while on standstill, the drive is turned externally by more than the value in
the positioning window after a positioning run has been finished correctly
This bit is reset:
- with each new run command