HAMPTON BAY DERRY GLF-2002 User manual

USE AND CARE GUIDE
DERRY ELECTRIC FIREPLACE
C US
INSTALLER: Leave this manual with the appliance.
CONSUMER: Retain this manual for future reference.
WARNING!
IF THE INFORMATION IN THIS MANUAL IS NOT FOLLOWED EXACTLY,
AN ELECTRICAL SHOCK OR FIRE MAY RESULT
CAUSING PROPERTY DAMAGE, PERSONAL INJURY OR LOSS OF LIFE.
IMPORTANT INSTRUCTIONS
PLEASE READ THIS MANUAL BEFORE INSTALLING AND USING APPLIANCE
Questions, problems, missing parts? Before returning to the store,
call Hampton Bay Customer Service
8 a.m. - 6 p.m., EST, Monday - Friday
855-HD-HAMPTON
HAMPTONBAY.COM
THANK YOU
We appreciate the trust and confidence you have placed in Hampton Bay through the purchase of this electric fireplace. We strive to continually
create quality products designed to enhance your home. Visit us online to see our full line of products available for your home improvement
needs. Thank you for choosing Hampton Bay!
Item #1000 014 011
Model #23-791, GLF-2002
20-10-177 REV. 11/2013

2
Table of Contents
Table of Contents ...................................2
Safety Information ..................................3
Warranty ..........................................5
Pre-Installation.....................................6
Installation ........................................9
Operation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Maintenance ......................................11
Care and Cleaning .................................12
Troubleshooting ...................................13
Service Parts......................................14
IMPORTANT: Read all instructions and warnings carefully before starting installation.
Failure to follow these instructions may result in a possible electric shock, injury to persons, fire hazard and will void the warranty.
Please read the Installation & Operating Instructions before using this appliance.
PRODUCT DAMAGE MAY OCCUR.
Never attempt to disassemble or alter the product in any way not instructed by this manual.
CAUTION

3 HAMPTONBAY.COM
PLEASE CONTACT 855-HD-HAMPTON FOR FURTHER ASSISTANCE.
Safety Information
Please read and understand this entire manual before attempting to assemble, operate or install the product.
□Read all instructions before using this appliance.
□This appliance is hot when in use. To avoid burns, do not let bare skin touch hot surfaces. If provided, use handles when moving this
appliance. Keep combustible materials, such as furniture, pillows, bedding, papers, clothes and curtains at least 3 ft. (914 mm) from
the front of this appliance and keep them away from the sides and rear.
CAUTION: Extreme caution is necessary when any heater
is used by or near children or invalids and whenever the
heater is left operating unattended.
□If possible, always unplug this appliance when not in use.
□Do not operate any heater with a damaged cord or plug or after the appliance malfunctions, has been dropped or damaged in any
manner.
□Any repairs to this appliance should be carried out by a qualified service person.
□Under no circumstances should this appliance be modified. Parts having to be removed for servicing must be replaced prior to
operating this appliance again.
□Do not use outdoors.
□This heater is not intended for use in bathrooms, laundry areas and similar indoor locations. Never place this appliance where it
may fall into a bathtub or other water container.
□Do not run the cord under carpeting. Do not cover the cord with throw rugs, runners or the like. Arrange the cord away from traffic
areas and where it will not be tripped over.
□To disconnect this appliance, turn the controls to the off position, then remove the plug from the outlet.
□Connect to properly grounded outlets only.
□This appliance, when installed, must be electrically grounded in accordance with local codes, with the current CSA C22.1 Canadian
Electrical codes or for USA installations, follow local codes and the National Electric Code, ANSI/NFPA No. 70.
□Do not insert or allow foreign objects to enter any ventilation or exhaust opening, as this may cause an electric shock, fire, or
damage to the appliance.
□To prevent possible fire, do not block air intakes or exhaust in any manner. Do not use on soft surfaces, like a bed, where
openings may become blocked.
□This appliance has hot and arcing or sparking parts inside. Do not use it in areas where gasoline, paint, or flammable liquids are
used or stored. This appliance should not be used as a drying rack for clothing, nor should Christmas stockings or decorations be
hung on or near it.
□Use this appliance only as described in this manual. Any other use not recommended by the manufacturer may cause fire, electric
shock, or injury to persons.
□Always plug heaters directly into a wall outlet/receptacle. Never use with an extension cord or relocatable power tap (outlet/power
strip) because of the risk of overheating the cord and the risk of fire. Extension cords are for temporary use only. If an extension
cord must be used, it must be UL/CSA certified, rated at 15A (1,875W), 125V maximum with 14 AWG minimum and constructed of
two current carrying conductors with ground. A heavy duty extension cord with the shortest length possible for the connection is
recommended and must not be longer than 50 ft. (15.2 m). Do not coil or cover the extension cord.
□“SAVE THESE INSTRUCTIONS FOR FUTURE USE”

4
Safety Information (continued)
WARNING: Electrical outlet wiring must comply with local
building codes and other applicable regulations to reduce
the risk of fire, electrical shock and injury to persons.
WARNING: Do not use this fireplace if any part of it has
been under water. Immediately call a qualified service
technician to inspect the fireplace and replace any part of
the electrical system which has been under water.
GROUNDING
PIN
METAL SCREW
GROUNDING
MEANS
COVER OF GROUNDED
OUTLET BOX
ADAPTER
Figure 1
GROUNDING
PIN
ELECTRICAL CONNECTION
GROUNDING INSTRUCTIONS
This heater is for use on 120 volts. The cord has a plug as shown at (A) in Figure 1. An adapter as shown at (C) is available
for connecting three-blade grounding-type plugs to two-slot receptacles. The green grounding lug extending from the
adapter must be connected to a permanent ground such as a properly grounded outlet box. The adapter should not be used
if a three-slot grounded receptacle is available.
NOTE: Adapters are NOT
for use in Canada.
DANGER
A 15-Amp, 120-Volt, 60 Hz circuit with a properly grounded outlet is required. Preferably, the item will be on a
dedicated circuit, as other appliances on the same circuit may cause the circuit breaker to trip or the fuse to blow
when the heater is in operation. The unit comes standard with a 6 ft. (1.8 m) long three wire cord, exiting the right side
of the item. Always plug the unit into a wall outlet/receptacle. An extension cord or re-locatable power tap, (outlet/
power strip), should never be used.
(A)
(B)
(D)
(C)

5
1-YEAR WARRANTY
WHAT IS COVERED
The manufacturer warrants that your new electric fireplace is free from manufacturing and material defects for a period of one year from
date of purchase, subject to the following conditions and limitations.
Variations in actual wood color and finishes which may result from natural characteristics of the wood, such as grain patterns, mineral
streaks and the like, are not considered defects. As wood continues to move and age you may notice these slight differences in color, even
on different parts of any individual unit. Sound knots and slight surface cracks are the true personality of a quality piece of wood furniture.
This electric fireplace must be installed and operated at all times in accordance with the instructions furnished with the product. Any
alteration, willful abuse, accident, or misuse of the product shall nullify this warranty. This warranty is non-transferrable, and is made to
the original owner, provided that the purchase was made through an authorized supplier of the manufacturer.This warranty is limited to the
repair or replacement of part(s) found to be defective in material or workmanship, provided that such part(s) have been subjected to normal
conditions of use and service, after said defect is confirmed by the manufacturer’s inspection. The manufacturer may, at its discretion, fully
discharge all obligations with respect to this warranty by refunding the wholesale price of the defective part(s).
WHAT IS NOT COVERED
Any installation, labor, construction, transportation, or other related costs/expenses arising from defective part(s), repair, replacement,
or otherwise of same, will not be covered by this warranty, nor shall the manufacturer assume responsibility for same. Further, the
manufacturer will not be responsible for any incidental, indirect, or consequential damages, except as provided by law.
All other warranties - expressed or implied - with respect to the product, its components and accessories, or any obligations/liabilities on
the part of the manufacturer are hereby expressly excluded. The manufacturer neither assumes, nor authorizes any third party to assume, on
its behalf, any other liabilities with respect to the sale of this product. The warranties as outlined within this document do not apply to non-
manufacturer accessories used in conjunction with the installation of this product.
This warranty does not cover the lightbulb(s) included with the fireplace.
This warranty is void if: the fireplace has been operated in atmospheres contaminated by chlorine, fluorine, or other damaging chemicals;
the fireplace is subjected to prolonged periods of dampness or condensation; the fireplace is altered, willfully abused, damaged by accident,
or misused in any way.
If warranty service is needed, contact the Customer Service Team at 855-HD-HAMPTON from 8 a.m. - 6 p.m., EST, Monday-Friday or visit
www.hamptonbay.com.
Make sure you have your warranty, your sales receipt, and the model/serial number of your product.
DO NOT ATTEMPT TO DO ANY SERVICE WORK YOURSELF.
Warranty
HAMPTONBAY.COM
PLEASE CONTACT 855-HD-HAMPTON FOR FURTHER ASSISTANCE.

6
AA BB CC DD EE FF
Phillips
screwdriver
TOOLS REQUIRED
PLANNING INSTALLATION
HARDWARE INCLUDED
Part Description Quantity
AA Wrench 1
BB Mounting Bracket 2
CC Screw (1-3/8 in.) 2
DD Nylon Strap 1
EE Wall Anchor 2
FF Screw (5/8 in.) 2
NOTE: Hardware not shown to actual size.
To avoid scratching the finish, assemble the product on a soft, non-abrasive surface, such as carpet or cardboard.
Assembly of this product may require more than one person.
Pre-Installation

7
PACKAGE CONTENTS
Part Description Quantity
A
B
C
Mantel (with fireplace insert)
Front Caster
Rear Brake Caster
1
2
2
D Remote Control 1
BC
A
D
Pre-Installation (continued)
HAMPTONBAY.COM
PLEASE CONTACT 855-HD-HAMPTON FOR FURTHER ASSISTANCE.

8
Specifications
Clearance to Combustibles
Sides
Floor
Top
Front
Rear
2 27/64 in. (61.5 mm)
0 in. (0 mm)
2 in. (51 mm)
36 in. (914 mm)
0 in. (0 mm)
Pre-Installation (continued)
Voltage 120 V AC
60Hz
1350W
12.5A
31.75” (806mm)
12.75” (324mm)
27.25” (692mm)
Frequency
Heater Rating
Max. Amps
Width
Depth
Height
31.75” (806mm)
12.75” (324mm)
27.25” (692mm)

9
Installation
Attaching the casters to the mantel
NOTE: To avoid scratching the finish, assemble the product
on a soft, non-abrasive surface, such as carpet or cardboard.
□Lay the mantel (A) on its back.
□Screw a front caster (B) into the pre-drilled hole in the
front-right corner of the mantel (A) base.
□Screw a rear brake caster (C) into the pre-drilled hole in
the right-rear corner of the mantle (A) base.
□Repeat this process for the left side of the mantel (A) base.
□Tighten all of the casters with the wrench (AA) provided.
□Attach a mounting bracket (BB) to the top edge of the back
of the mantel (A) by inserting two screws (FF) through the
mounting bracket (BB) and into the pre-drilled holes in the
mantel (A). Tighten with a screwdriver.
□Attach a mounting bracket (BB) to the wall in the location
you have selected to put the mantel (A) by positioning the
mounting bracket (BB) at approximately the same height
as the mounting bracket (BB) previously attached to the
mantel (A).
□Insert screws (CC) through the mounting bracket (BB) and
into a wall stud. If there is no stud present, insert wall
anchors (EE) before inserting the screws (CC). Tighten with
a screwdriver.
DANGER: This product is only a deterrent. It is not a
substitute for proper adult supervision.
□Set the mantel (A) 2-3 inches from the wall with both
mounting brackets (BB) aligned.
□Slip the nylon strap (DD) through the openings in each of
the mounting brackets (BB) and secure the nylon strap
(DD). This will help prevent the mantel from tipping.
CC
DD
BB
FF
BB
C
B
A
EE BB
CC
FF
BB
DD
FF
A
BB
HAMPTONBAY.COM
PLEASE CONTACT 855-HD-HAMPTON FOR FURTHER ASSISTANCE.
WARNING: Failure to install casters may interrupt airflow
and cause the heater to shut down.
12
34
Attaching the mounting bracket to
the mantel
Attaching the mounting bracket
to the wall Attaching the nylon strap

10
Operation
NOTE: When the heat function is used for the first time, a slight
odor may be present. This is normal and should not occur again
unless the heater is not used for an extended period of time.
1Using the Control Panel
□Check that the heater outlet grill is not covered or
obstructed in anyway, and make sure the power to the
unit is switched on.
□Press the appropriate button to operate your fireplace:
14 2
3
1. Main Power Button: This button supplies power to all
of the fireplace functions. It must be turned on for the
fireplace to work.
2. Heater Control Button: This button controls the heater
ON/OFF and 5 temperature modes from Low to High.
When the heater is first turned on, it will come on at
the lowest room temperature setting. The log set will
remember the last heat setting and in later use the
heater will start at that setting, unless power to the
unit has been interrupted. Each time the temperature
button is pressed, the temperature set point increases,
allowing you to adjust the ambient temperature.
3. Heater Locking Function: When fireplace is ON, press
the main power button (1) for 10 seconds. The heater
will be locked, and the heater control button (2) on the
control panel as well as on the remote control will be
disabled. Before the heater is locked, the flame will
flash 6 times. To unlock the the heater, press the main
power button (1) for 10 seconds. Before the heater is
unlocked, the flame will flash 6 times.
4. Flame Control Button: This button controls the
brightness of the flame effect with settings at High,
Medium, and Low. When the log set is first turned on,
the flame will come on at the highest setting. The log
set will remember the last flame setting used and in
later use the flame brightness will start at that setting,
unless power to the unit has been interrupted. Each
time the flame button is pressed, the flame brightness
decreases. The only way to turn off the flame effect
completely is to turn off the main power button (1).

11
Maintenance
GLASS INFORMATION
□Under no circumstances should this product be operated with broken glass.
□Do not strike or slam the glass.
□Do not use abrasive cleaners to clean the glass.
□This product uses tempered glass. Replacement of the glass supplied by the manufacturer should be done by a qualified
service person.
LIGHT BULB INSPECTION AND REPLACEMENT
WARNING: Light bulbs become very hot during use. Allow
at least 10 minutes for the bulbs to cool before touching.
WARNING: Do not exceed 40 watts per bulb. Use of
higher rated bulbs may result in a fire, causing property
damage or personal injury.
CAUTION: Do not operate this heater without the access
panel in place. Do not remove the back cover of this heater.
There are no serviceable parts inside.
The flame effect is created by two 40-Watt light bulbs with an E-12
(small) socket base. Use only this type of light bulb. If the flame \
effect does not work, the bulbs may have come loose or been
damaged during shipping.
To inspect or replace the bulbs:
□Unplug the power cord from the outlet.
□Locate the access panel on the back of the stove.
□Remove the screws and the panel.
□Check the bulbs to be sure they are finger tight and in working
order.
□Replace any damaged or faulty bulbs. Reattach the access
panel.
HAMPTONBAY.COM
PLEASE CONTACT 855-HD-HAMPTON FOR FURTHER ASSISTANCE.

12
Care & Cleaning
□Always turn the heater OFF and unplug the power cord from the outlet before cleaning.
□Use a vacuum or duster to remove dust and dirt from the heater and vent areas.
□To maintain the finish, clean with a soft, slightly damp cloth and buff with a dry cloth. Never use abrasive cleansers, liquid sprays, or
any cleaner that could scratch the surface.
□Wood furniture should never be dragged across a floor. The added stress from dragging the unit may cause the dragged edge to
splinter, or it may cause a joint to loosen.
Maintenance (continued)
Any electrical repairs or rewiring of this unit should be carried out by a licensed electrician in accordance with national and local codes.
CIRCUIT DIAGRAM
Disconnect power before servicing.
Any electrical re-wiring of this appliance must be done by a qualified electrician. This wiring must be done in
accordance with local codes and/or in Canada with the current CSA C22.1 Canadian Electrical Code, and for US
installations, the National Electrical Code ANSI/NFPA NO 70.
If repairing or replacing any electrical component or wiring, the original wire routing, color coding and securing
locations must be followed.
DANGER
WARNING: Disconnect power before servicing.

13
Troubleshooting
Problem Possible Cause Solution
The fireplace does
not operate.
The power light is ON but
the flame effect is not
visible.
There is excessivee
noise when the heater is
operating.
The heater is not
operating.
□The fireplace is not plugged in.
□A circuit breaker is tripped or a fuse
blown.
□The ON/OFF switch is defective.
□There is loose wiring.
□The fireplace is not operating
correctly.
□There are loose light bulb(s).
□There are burnt out light bulb(s).
□The fan is defective.
□The heater assembly is defective.
□The fireplace is not operating
correctly.
□The heater switch is defective.
□The heater assembly is defective.
□There is loose wiring.
□The vents are dirty or clogged.
□Make sure the fireplace is plugged in
to a standard 120V outlet.
□Check additional appliances on the
circuit; ideally the fireplace should be
on a dedicated 15-amp circuit.
□Call customer service.
□Call customer service.
□Refer to the operating instructions.
□Tighten the light bulb(s).
□Replace the light bulb(s).
□Call customer service.
□Call customer service.
□Refer to the operating instructions.
□Call customer service.
□Call customer service.
□Call customer service.
□Unplug the unit. Clear the vent area of
dust and debris. Wait ten minutes, plug
the unit in again and turn on the heater.
□Install the casters according to installation
instructions.
If you have any questions regarding the product, please call Hampton Bay Customer Service, 855-HD-HAMPTON, 8 a.m. – 6 p.m. EST,
Monday – Friday.
HAMPTONBAY.COM
PLEASE CONTACT 855-HD-HAMPTON FOR FURTHER ASSISTANCE.
□The casters have not been installed.

Service Parts
Part Description Part #
1 Back Panel EF237916501AC
2 Flame Panel EF237916502AC
3 Glass EF237916503AC
4 Screen EF237916504AC
5 Front Decorative Panel EF237916505AC
6 Front Panel EF237916506AC
7 Left Brick Side Panel EF237916507AC
8
9
10
11
12
13
14
Right Brick Side Panel
Top Panel
Remote Control
Main Board (PCB)
Logset
Flame Reflector
Control Panel
EF237916508AC
EF237916509AC
EF33510AS
EF237916510AC
EF237916511AC
EF237916512AC
EF237916513AC
Part Description Part #
15 Control Panel Circuit Board EF237916514AC
16 Power Cord & Connector EF24900015AC
17 Synchronous Motor EFES323020ST
18 Lamp Socket & Bracket EFES323021ST
19 Fan Heater EF23022501X
20 Access Panel EFES323008ST
21
22
Front Caster
Rear Brake Caster
20-09-155
20-09-162
23
24
25
26
27
28
Wrench
Mounting Bracket
1-3/8 in. Screw
Nylon Strap
Wall Anchor
5/8 in. Screw
20-09-156
20-09-157
20-09-158
20-09-159
20-09-160
20-09-161
14
1 2 3 4
56789
10
11
12
13
15 16
14
17
18
19
20
21 22
23 24
26 27
25 28

Printed in China
Questions, problems, missing parts? Before returning to the store,
call Hampton Bay Customer Service
8 a.m.-6 p.m., EST, Monday-Friday
855-HD-HAMPTON
HAMPTONBAY.COM
Retain this manual for future use.
Manufactured by: GHP Group, Inc. • 6440 W. Howard St. • Niles, IL 60714-3302

GUÍA DE USO Y CUIDADO
CHIMENEA ELÉCTRICA DERRY
C US
INSTALADOR: Deje este manual con el dispositivo.
CONSUMIDOR: Conserve este manual para uso futuro.
¡ADVERTENCIA!
SI LA INFORMACIÓN EN ESTE MANUAL NO SE SIGUE CON EXACTITUD,
PUEDE RESULTAR UN CHOQUE ELÉCTRICO O INCENDIO
OCASIONANDO DAÑOS A LA PROPIEDAD, LESIONES PERSONALES O LA MUERTE.
INSTRUCCIONES IMPORTANTES
POR FAVOR, LEA ESTE MANUAL ANTES DE LA INSTALACIÓN Y USO DEL DISPOSITIVO
¿Tiene preguntas, problemas, o faltan piezas? Antes de regresar a la tienda,
llame a Servicio al Cliente de Hampton Bay
de lunes a viernes de 8 a.m. a 6 p.m., hora local del Este
1-877-527-0313
HAMPTONBAY.COM
GRACIAS
Apreciamos la confianza que ha depositado en Hampton Bay por la compra de esta chimenea eléctrica. Nos esforzamos por crear continuamente productos de
calidad diseñados para mejorar su hogar. Visítenos en internet para ver nuestra línea completa de productos disponibles para sus necesidades de mejorar su
hogar. ¡Gracias por elegir a Hampton Bay!
Núm. de artículo 1000 014 011
Núm. de modelo 23-791, GLF-2002
20-10-177 REV. 11/2013

2
Tabla de contenido
Tabla de contenido..................................2
Información de seguridad ............................3
Garantía. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Pre-instalación .....................................6
Instalación ........................................9
Operación ........................................10
Mantenimiento ....................................11
Cuidado y limpieza .................................12
Resolución de fallas ................................13
Piezas de repuesto .................................14
IMPORTANTE: Lea cuidadosamente todas las instrucciones y advertencias antes de comenzar la instalación.
No seguir estas instrucciones puede resultar en un posible choque eléctrico, lesiones a las personas, peligro de incendio y anulará la garantía.
Lea las Instrucciones de instalación y operación antes de usar este dispositivo.
PUEDEN OCURRIR DAÑOS AL PRODUCTO.
Nunca intente desmontar o alterar el producto en ninguna manera que no la indique este manual.
PRECAUCIÓN

3 HAMPTONBAY.COM
PARA OBTENER ASISTENCIA, PÓNGASE EN CONTACTO LLAMANDO AL 855-HD-HAMPTON.
Información de seguridad
Por favor, lea y comprenda este manual completo antes de intentar ensamblar, operar o instalar el producto.
□Lea todas las instrucciones antes de usar este dispositivo.
□Este dispositivo se calienta cuando está en uso. Para evitar quemaduras, no permita que la piel desnuda toque las superficies calientes. Si se
proporcionan, use manijas cuando mueva este dispositivo. Mantenga los materiales combustibles, como muebles, almohadas, ropa de cama,
papeles, telas y cortinas al menos a 3 pies (914 mm) del frente de este dispositivo y manténgalos lejos de los lados y la parte trasera.
PRECAUCIÓN: Es necesario que se tomen extremas precauciones
cuando cualquier calefactor es usado por o cerca de niños o inválidos y
siempre que el calefactor se deje funcionando y desatendido.
□Si es posible, desconecte siempre este dispositivo cuando no esté en uso.
□No opere ningún calefactor con un cable o enchufe dañado o después de que el dispositivo funcione mal, se haya caído o dañado en alguna
manera.
□Cualquier reparación a este dispositivo deberá ser hecha por una persona de servicio calificada.
□Bajo ninguna circunstancia este aparato debe ser modificado. Las piezas que tienen que ser retiradas para servicio deben ser reemplazadas antes
de operar de nuevo este dispositivo.
□No lo use en exteriores.
□Este calefactor no está diseñado para ser usado en baños, áreas de lavado y ubicaciones de interiores similares. Nunca coloque este dispositivo
donde se pueda caer dentro de una tina u otro contenedor de agua.
□No tienda el cable bajo las alfombras. No cubra el cable con alfombras decorativas, alfombras de pasillo o cosas semejantes. Coloque el cable
lejos de áreas de tráfico y donde no se pueda tropezar con él.
□Para desconectar este dispositivo, apague los controles y retire el enchufe del tomacorriente.
□Conecte a tomacorrientes con conexión a tierra solamente.
□Este dispositivo, cuando está instalado, debe estar electricamente aterrizado de acuerdo con códigos locales, con los Códigos Eléctricos
Canadienses actuales CSA C22.1 o para instalaciones en los EE. UU., siga los códigos locales y el Código Eléctrico Nacional ANSI/NFPA NO 70.
□No inserte ni permita que objetos extraños ingresen a cualquier abertura de ventilación o escape, ya que esto puede causar un choque eléctrico o
incendio, o daños al dispositivo.
□Para evitar un posible incendio, no bloquee las entradas de aire y escapes de ninguna manera. No lo use en superficies suaves, como una cama,
donde las aberturas se puedan bloquear.
□Este dispositivo tiene en el interior piezas calientes o de arco eléctrico o que generan chispas. No lo use en áreas donde se use o almacene
gasolina, pintura o líquidos inflamables. Este dispositivo no debe ser usado como tendedero para secar ropa, ni para colgar medias o decoraciones
de Navidad en o cerca de él.
□Use este dispositivo solamente como se describe en este manual. Cualquier otro uso no recomendado por el fabricante puede causar incendio,
choque eléctrico o lesiones a las personas.
□Conecte siempre los calefactores directamente en un tomacorriente/receptáculo de pared. Nunca use un cable de extensión o tomacorriente móvil
(tomacorriente/enchufe múltiple) debido al riesgo de sobrecalentamiento del cable y el riesgo de incendio. Los cables de extensión son solo para
uso temporal. Si se debe usar un cable de extensión, debe ser UL/CSA certificado, con capacidad nominal de 15A (1,875W), 125V máximo con 14
AWG mínimo y construido de dos conductores de corriente con tierra. Se recomienda un cable de extensión resistente con la longitud más corta
posible para la conexión y no debe ser más largo que 50 pies (15.2 m). No enrolle ni cubra el cable de extensión.
□"CONSERVE ESTAS INSTRUCCIONES PARA USO FUTURO"

4
Información de seguridad (continuación)
ADVERTENCIA: El cableado del tomacorriente eléctrico debe
cumplir con los códigos locales y otras regulaciones aplicables
para reducir el riesgo de incendio, choque eléctrico y lesiones a las
personas.
ADVERTENCIA: No use esta chimenea si alguna pieza de la
chimenea ha estado bajo el agua. Llame de inmediato a un técnico
de servicio calificado para inspeccionar la chimenea y reemplazar
cualquier pieza del sistema eléctrico que haya estado bajo el agua.
CUCHILLA
DE TIERRA
TORNILLO METÁLICO
PUNTO PARA
CONEXIÓN A
TIERRA
CUBIERTA DE CAJA
DE SALIDA ATERRIZADA
ADAPTADOR
Figura 1
PUNTO PARA
CONEXIÓN A
DE TIERRA
CONEXIÓN ELÉCTRICA
INSTRUCCIONES DE CONEXIÓN A TIERRA
Este calefactor es para uso con 120 voltios. El cable tiene un enchufe como se muestra en (A) en la Figura 1. Un adaptador como se
muestra en (C) está disponible para conectar enchufes de tres cuchillas con conexión a tierra. La orejeta verde de conexión a tierra que
se extiende del adaptador, debe ser conectada a una tierra permanente como una caja de salida aterrizada adecuadamente. El adaptador
no debe ser usado si está disponible un receptáculo aterrizado de tres ranuras.
NOTA: Los adaptadores NO son
para uso en Canadá.
PELIGRO
Se requiere un circuito de 15 Amp, 120 Voltios, 60 Hz con un tomacorriente aterrizado adecuadamente. De preferencia, el artículo
estará en un circuito dedicado, ya que otros dispositivos en el mismo circuito podrían hacer que el disyuntor de circuito se active o
el fusible explote cuando el calefactor esté en funcionamiento. La unidad viene estándar con un cable de tres alambres de 6 pies
(1.8 m) de longitud, que sale del lado derecho del artículo. Conecte siempre la unidad en un tomacorriente/receptáculo de pared.
Nunca se debe de usar un cable de extensión o tomacorriente móvil (tomacorriente/enchufe múltiple).
(A)
(B)
(D)
(C)

5 HAMPTONBAY.COM
PARA OBTENER ASISTENCIA, PÓNGASE EN CONTACTO LLAMANDO AL 855-HD-HAMPTON.
GARANTÍA DE 1 AÑO
LO QUE ESTÁ CUBIERTO
El fabricante garantiza que su nueva chimenea eléctrica está libre de defectos de fabricación y materiales por un periodo de un año a partir de la fecha de
compra, sujeto a las siguientes condiciones y limitaciones.
Las variaciones en el color real de la madera y los acabados que pueden resultar de las características naturales de la madera, como patrones de grano,
marcas minerales y cosas semejantes, no son considerados defectos. A medida la madera envejece, puede notar estas ligeras diferencias en color, incluso
en partes diferentes de cualquier unidad individual. Los nudos en buen estado y las grietas ligeras de la superficie son la verdadera personalidad de una
pieza de calidad de muebles de madera.
Esta chimenea eléctrica debe ser instalada y operada en todo momento de acuerdo con las instrucciones proporcionadas con el producto. Cualquier
alteración, abuso intencionado, accidente o mal uso del producto anulará esta garantía. Esta garantía es intransferible y es hecha al propietario original,
siempre que la compra fue hecha mediante un proveedor autorizado del fabricante. Esta garantía está limitada a la reparación o reemplazo de pieza(s)
que se encuentren defectuosas en materiales o mano de obra, siempre que tal(es) pieza(s) hayan estado sujetas a condiciones normales de uso y servicio,
luego de que dicho defecto sea confirmado por la inspección de fabricante. El fabricante puede, a su discreción, liberar de todas las obligaciones, con
respecto a esta garantía mediante el reembolso del precio al por mayor de la(s) pieza(s) defectuosa(s).
LO QUE NO ESTÁ CUBIERTO
Cualquier instalación, trabajo, construcción, transporte u otros costos/gastos que surjan de pieza(s) defectuosa(s), reparación, reemplazo u otra cosa similar,
no será cubierta por esta garantía y tampoco el fabricante asumirá responsabilidad por lo mismo. Además, el fabricante no será responsable de ningún
daño incidental, indirecto o consecuente, excepto como lo establezca la ley.
Todas las otras garantías, expresas o implícitas, con respecto al producto, sus componentes y accesorios, o cualquier obligación/responsabilidad civil sobre
la pieza del fabricante, por la presente se excluyen expresamente. El fabricante tampoco asume, ni autoriza a ninguna tercera parte a asumir, en su nombre,
cualquier otra responsabilidad civil con respecto a la venta de este producto. Las garantías como están descritas dentro de este documento, no aplican a
accesorios que no son del fabricante usadas junto con la instalación de este producto.
Esta garantía no cubre la(s) bombilla(s) incluidas con la chimenea.
Esta garantía no tiene validez si: la chimenea ha sido operada en atmósferas contaminadas con cloro, flúor u otro químico dañino; la chimenea está sujeta a
periodos prolongados de humedad o condensación; la chimenea es alterada, maltratada intencionalmente, dañada por accidente o usada incorrectamente
en cualquier manera.
Si se necesita servicio de garantía, póngase en contacto con el Equipo de Servicio al Cliente llamando al 855-HD-HAMPTON de lunes a viernes de 8 a.m. a
6 p.m., hora local del Este o visite www.hamptonbay.com.
Asegúrese de tener su garantía, su recibo de venta y el número de modelo/serie de su producto.
NO INTENTE HACER TRABAJO DE SERVICIO USTED MISMO.
Garantía