HAMPTON BAY H27 Quick start guide

FPI FIREPLACE PRODUCTS INTERNATIONAL LTD. 6988 Venture St., Delta, BC Canada, V4G 1H4
918-812
MODELS: H27-NG Natural Gas H27-LP Propane
01/19/10
H27 Direct Vent Gas Fireplace
Owners &
Installation Manual
WARNING:
If the information in these instructions are not
followed exactly, a fire or explosion may result
causing property damage, personal injury or loss
of life.
FOR YOUR SAFETY
Do not store or use gasoline or other flammable
vapours and liquids in the vicinity of this or any
other appliance.
Installation and service must be performed by
a qualified installer, service agency or the gas
supplier.
FOR YOUR SAFETY
What to do if you smell gas:
Do not try to light any appliance
Do not touch any electrical switch:
do not use any phone in your
building.
Immediately call your gas supplier
from a neighbour's phone. Follow
the gas supplier's instructions.
If you cannot reach your gas sup-
plier, call the fire department.
This appliance may only be
installed in an aftermarket
permanently located, manu-
factured(USAonly)ormobile
home,wherenotprohibitedby
local codes.
This appliance is only for use
with the type of gas indicated
on the rating plate. This ap-
pliance is not convertible for
use with other gases, unless
a certified kit is used.
Tested by: Installer: Please complete the details on the back cover
and leave this manual with the homeowner.
Homeowner: Please keep these instructions for future reference.
www.hampton-fire.com

2Hampton®H27 Direct Vent Freestanding Gas Stove
HAMPTON®
Direct Vent Freestanding Gas Stove
To the New Owner:
Congratulations!
You are the owner of a state-of-the-art Hampton®Gas Stove by REGENCY FIREPLACE PRODUCTS. The H27 is
a hand crafted appliance and has been designed to provide you with all the warmth and charm of a wood fireplace
at the flick of a switch. The model H27 has been approved by Warnock Hersey for both safety and efficiency. As it
also bears our own mark, it promises to provide you with economy, comfort and security for many trouble free years
to follow. Please take a moment now to acquaint yourself with these instructions and the many features of your
Hampton®Stove.

Hampton®H27 Direct Vent Freestanding Gas Stove 3
TABLE OF CONTENTS
SAFETY LABEL
Copy of Safety Label.....................................................4
UNIT DIMENSIONS
Unit Dimensions ..........................................................6
INSTALLATION
Important Message ......................................................7
Specifications ................................................................7
General Safety Information............................................8
Installation Checklist......................................................8
Clearances To Combustibles.........................................8
Locating Your Gas Stove...............................................9
Manufactured Mobile Home Additional Requirements ..9
Combustion and Ventilation Air......................................9
Optional Fan Installation................................................9
Venting Introduction.....................................................11
Installation Precautions ...............................................11
Vent Restrictor Position...............................................11
Rotating 45oElbow......................................................11
Exterior Vent Terminal Locations.................................12
4” x 6-5/8” Rigid Pipe Cross Reference Chart.............13
Rigid Pipe Venting Systems ........................................15
Venting Arrangements.................................................16
Vertical Termination with Co-linear Flex System .........19
DV Stove Horizontal Vent Kit.......................................20
Residential and Manufactured Homes ........................22
Minimum horizontal termination Installations.......22
Dura-Vent Termination Kit............................................23
Horizontal terminations................................................24
Vertical Terminations ...................................................25
Converting Chimney to Direct Vent System ................27
Cathedral Ceilings.......................................................28
High Elevation .............................................................28
Gas Connection...........................................................28
Aeration Adjustment ....................................................29
Gas Pipe .....................................................................29
Pressure Testing..........................................................29
Conversion from NG to LP ..........................................30
Log Set Installation......................................................33
Optional Side Shelves Installation...............................35
Wall Thermostat ..........................................................35
Remote Control ..........................................................35
Final Check..................................................................36
Wiring Diagrams..........................................................36
OPERATING INSTRUCTIONS
Operating Instructions .................................................38
Lighting Procedure ......................................................38
Shutdown Procedure...................................................38
First Fire ......................................................................38
Automatic Convection Fan Operation..........................38
Copy of the Lighting Plate Instructions .......................39
MAINTENANCE
Normal Operating Sounds of Gas Appliances.............40
Maintenance Instructions.............................................40
Log Replacement ........................................................41
Glass Replacement.....................................................41
Fan Maintenance.........................................................41
Removing Valve...........................................................42
Installing Valve Assembly............................................42
PARTS LIST
Main Assembly ............................................................43
Burner & Log Assembly...............................................45
WARRANTY
Warranty ....................................................................47

4Hampton®H27 Direct Vent Freestanding Gas Stove
This is a copy of the label that accompanies
each Direct Vent Freestanding Gas Stove.
We have printed a copy of the contents here
for your review.
SAFETY LABEL
COPY OF SAFETY LABEL
NOTE: Hampton®units are constantly being
improved. Check the label on the unit and if
there is a difference, the label on the unit is
the correct one.
Listed:
Certified for/Certifi e pour:
VENTED GAS FIREPLACE HEATER
CANADA and U.S.A.
é
MAY BE INSTALLED IN MANUFACTURED (MOBILE) HOMES AFTER FIRST SALE
ÉÉQUIP A L'UISINE POUR GAZ NATURAL
ÉÉQUIP A L'UISINE POUR GAZ PROPANE
5" WC/C.E. (1.25 kPa)
3.8" WC/C.E. (0.94 kPa)
1.1" WC/C.E. (0.27 kPa)
12" WC/C.E. (3.00 kPa)
11" WC/C.E. (2.74 kPa)
2.9" WC/C.E. (0.72 kPa)
Minimum supply pressure
Manifold pressure High
Manifold pressure Low
Minimum supply pressure
Manifold pressure High
Manifold pressure Low
DUPLICATE SERIAL NO.
DO NOT REMOVE THIS LABEL /
NE PAS ENLEVER CETTE ÉTIQUETTE
351
351
Made in Canada/Fabrique au Canada
FPI Fireplace Products International Ltd. Delta, BC, Canada
Minimum Clearances to Combustibles/Degagement Minimum De Materiaux Combustibles
C 2" / 50mm
E 2"/50mm
A 6"/150mm
B 3"/75mm
Minimum ceiling height from top of unit: mm
Minimum plafond hauteur en haut de
l'appareil: 24"/610mm
24"/610
Minimum clearance of Vent Terminal
to Outside Corner & Inside Corner:
with AstroCap 6"/150mm
with Dura-Vent Cap 12"/300mm
VENTED GAS FIREPLACE HEATER: This appliance must be installed in accordance with local codes, if any; if none,
follow:the national Fuel Gas Code, ANSI Z223.1, or Natural Gas and Propane Installation Code, CSA B149.1.Electrical
Supply (115 V, 1.13A, 60 Hz). This vented gas fireplace heater is not for use with filters.
: Installer l`appareil selon les codes ou reglements locaux, ou, en l`absence de tels
r glements, selon les codes installation ANS Z223.1, National Fuel Gas Code ou CSA-B149.1 en vigueur.
Not for use with solid fuels.
FOYER AU GAZ À ÈVACUATION
è d’ I Alimentation
électrique. Ne doit pas être utilisé avec un combustible solide.
Serial No./ No de serie
918-813
Maximum Input
Minimum Input
Orifice size
Altitude
Maximum Input
Minimum Input
Orifice size
Altitude
FACTORY EQUIPPED FOR NATURAL GAS Model:H27-NG
FACTORY EQUIPPED FOR PROPANE GAS Model:H27-LP
Pression d'allimentation minimum
Pression la tubulure d' chappement lev e
Pression la tubulure d' chappement basse
à
àééé
é
Pression d'allimentation minimum
Pression la tubulure d' chappement lev e
Pression la tubulure d' chappement basse
à
àééé
é
E
E
A
A
B
Left Side Wall
Right Side Wall
Horizontal
Pipe
25,000 Btu/h (7.32 Kw/h)
12,500 Btu/h (3.66 Kw/h)
#42 DMS (2.37mm)
0-4500 ft/pi (0-1372m)
23,000 Btu/h (6.74 Kw/h)
11,500 Btu/h (3.37 Kw/h)
#54 DMS (1.4mm)
0-4500 ft/pi (0-1372m)
D bit Calorifique maximum
D bit Calorifique minimum
Dimensions de l'orifice
L'altitude
é
é
D bit Calorifique maximum
D bit Calorifique minimum
Dimensions de l'orifice
L'altitude
é
é
A
Left Side Wall
Right Side Wall
C
Vertical
Pipe
WN# 16378
Tested to: Gas-Fired Appliances For Use At High
Altitudes CGA 2-17-M91, ANSI Z21.88a-2007/CSA 2.33a-2007Vented Gas Fireplace Heaters
See Manual for details
Model/Modele:
H27-NG
Model/Modele:
H27-LP
For the State of Massachusetts, installation and repair must be done by a plumber or gasfitter licensed in the
Commonwealth of Massachusetts.
For the State of Massachusetts, flexible connectors shall not exceed 36 inches in length.
For the State of Massachusetts, the appliances individual manual shut-off must be a t-handle type valve.
The State of Massachusetts requires the installation of a carbon monoxide alarm in accordance with NFPA 720
and a CO alarm with battery back up in the same room where the gas appliance is installed.

Hampton®H27 Direct Vent Freestanding Gas Stove 5
REQUIREMENTS
5.08: Modifications to NFPA-54, Chapter 10
(2) Revise 10.8.3 by adding the following additional requirements:
(a) For all side wall horizontally vented gas fueled equipment installed in every dwelling, building or structure used in whole or in part for
residential purposes, including those owned or operated by the Commonwealth and where the side wall exhaust vent termination is less than
seven (7) feet above finished grade in the area of the venting, including but not limited to decks and porches, the following requirements shall
be satisfied:
1. INSTALLATION OF CARBON MONOXIDE DETECTORS. At the time of installation of the side wall horizontal vented gas fueled
equipment, the installing plumber or gasfitter shall observe that a hard wired carbon monoxide detector with an alarm and battery back-up is
installed on the floor level where the gas equipment is to be installed. In addition, the installing plumber or gasfitter shall observe that a battery
operated or hard wired carbon monoxide detector with an alarm is installed on each additional level of the dwelling, building or structure
served by the side wall horizontal vented gas fueled equipment. It shall be the responsibility of the property owner to secure the services of
qualified licensed professionals for the installation of hard wired carbon monoxide detectors
a. In the event that the side wall horizontally vented gas fueled equipment is installed in a crawl space or an attic, the hard wired carbon
monoxide detector with alarm and battery back-up may be installed on the next adjacent floor level.
b. In the event that the requirements of this subdivision can not be met at the time of completion of installation, the owner shall have a period of
thirty (30) days to comply with the above requirements; provided, however, that during said thirty (30) day period, a battery operated carbon
monoxide detector with an alarm shall be installed.
2. APPROVED CARBON MONOXIDE DETECTORS. Each carbon monoxide detector as required in accordance with the above provisions
shall comply with NFPA 720 and be ANSI/UL 2034 listed and IAS certified.
3. SIGNAGE. A metal or plastic identification plate shall be permanently mounted to the exterior of the building at a minimum height of eight
(8) feet above grade directly in line with the exhaust vent terminal for the horizontally vented gas fueled heating appliance or equipment. The
sign shall read, in print size no less than one-half (1/2) inch in size, "GAS VENT DIRECTLY BELOW. KEEP CLEAR OF ALL
OBSTRUCTIONS".
4. INSPECTION. The state or local gas inspector of the side wall horizontally vented gas fueled equipment shall not approve the installation
unless, upon inspection, the inspector observes carbon monoxide detectors and signage installed in accordance with the provisions of 248 CMR
5.08(2)(a)1 through 4.
(b) EXEMPTIONS: The following equipment is exempt from 248 CMR 5.08(2)(a)1 through 4:
1. The equipment listed in Chapter 10 entitled "Equipment Not Required To Be Vented" in the most current edition of NFPA 54 as adopted by
the Board; and
2. Product Approved side wall horizontally vented gas fueled equipment installed in a room or structure separate from the dwelling, building or
structure used in whole or in part for residential purposes.
(c) MANUFACTURER REQUIREMENTS - GAS EQUIPMENT VENTING SYSTEM PROVIDED. When the manufacturer of Product
Approved side wall horizontally vented gas equipment provides a venting system design or venting system components with the equipment, the
instructions provided by the manufacturer for installation of the equipment and the venting system shall include:
1. Detailed instructions for the installation of the venting system design or the venting system components; and
2. A complete parts list for the venting system design or venting system.
(d) MANUFACTURER REQUIREMENTS - GAS EQUIPMENT VENTING SYSTEM NOT PROVIDED. When the manufacturer of a
Product Approved side wall horizontally vented gas fueled equipment does not provide the parts for venting the flue gases, but identifies
"special venting systems", the following requirements shall be satisfied by the manufacturer:
1. The referenced "special venting system" instructions shall be included with the appliance or equipment installation instructions; and
2. The "special venting systems" shall be Product Approved by the Board, and the instructions for that system shall include a parts list and
detailed installation instructions.
(e) A copy of all installation instructions for all Product Approved side wall horizontally vented gas fueled equipment, all venting instructions,
all parts lists for venting instructions, and/or all venting design instructions shall remain with the appliance or equipment at the completion of
the installation.
MA Code - CO Detector
(for the State of Massachusetts only)

6Hampton®H27 Direct Vent Freestanding Gas Stove
UNIT DIMENSIONS
** Shown with optional side shelves.

Hampton®H27 Direct Vent Freestanding Gas Stove 7
IMPORTANT MESSAGE
SAVE THESE
INSTRUCTIONS
The Direct Vent Freestanding Gas Stove must
be installed in accordance with these instruc-
tions. Carefully read all the instructions in this
manual first. Consult the building authority
having jurisdiction to determine the need for a
permit prior to starting the installation.
Note: Failure to follow the instructions
could cause a malfunction of the
heater which could result in death,
serious bodily injury, and/or prop-
erty damage. Failure to follow these
instructions may also void your fire
insurance and/or warranty.
Note: These instructions take precedence
over Simpson Dura-Vent instruc-
tions.
SPECIFICATIONS
Fuels: H27-NG is approved for use with
natural gas.
H27-LPisapprovedforusewithlique-
fied petroleum gases (propane).
Electrical: 120V A.C. system.
Optional Circulation Fan:
Variable speed, 125/75.
Log Sets: Ceramic fibre, 4 per set.
Vent System: Coaxial (6-5/8" outer / 4" inner
liner) rigid flue and termination cap.
INFORMATION FOR
MOBILE /
MANUFACTURED
HOMES
AFTER FIRST SALE
This Hampton®product has been tested and
listed by ITS Testing Services as a Direct Vent
Wall Furnace to the following standards:
CGA-2.17-M91, and ANSI Z21.88a-2007/CSA
2.33a-2007.
This Direct Vent System Appliance must be
installedinaccordancewith themanufacturer's
installation instructions and the Manufactured
Home Construction and Safety Standard, Title
24 CFR, Part 3280, or the current Standard of
Fire Safety Criteria for Manufactured Home
Installations, Sites, and Communities ANSI/
NFPA 501A, and with CAN/CSA Z240-MH
Mobile Home Standard in Canada.
INSTALLATION
Thisapplianceinstallation mustcomplywith the
manufacturer'sinstallationinstructionsandlocal
codes, if any. In the absence of local codes fol-
low the current National Fuel Gas Code, ANSI
Z223.1andthe currentNationalElectrical Code
ANSI/NFPA 70 in the U.S.A., and the current
CAN/CGA B149 Gas Installation Code and the
current Canadian Electrical Code CSA C22.1
in Canada.
This Hampton®Mobile/Manufactured
Home Listed appliance comes factory
equipped with a means to secure the
unit.
This Hampton®Mobile/Manufactured
Homelistedappliancecomesequipped
with a dedicated #8 ground lug to which
an 18 gauge copper wire from the steel
chassis ground must be attached.
Thisappliancemayonlybeinstalledin
an aftermarket permanently located,
manufactured (USA only) or mobile
home, where not prohibited by local
codes.
This appliance is only for use with
thetypeofgasindicatedontherating
plate. This appliance is not convert-
ible for use with other gases, unless
a certified kit is used.
INSTALLATION AND REPAIRS
SHOULD BE DONE BY A QUALI-
FIED SERVICE PERSON. THIS AP-
PLIANCESHOULDBEINSTALLED,
REPAIRED, INSPECTED BEFORE
USEANDAT LEASTANNUALLYBY
A QUALIFIED SERVICE PERSON.
MOREFREQUENTCLEANINGMAY
BEREQUIREDDUETOEXCESSIVE
LINTFROMCARPETING,ETC. ITIS
IMPERATIVE THAT THE CONTROL
COMPARTMENT, BURNERS AND
CIRCULATINGAIRPASSAGEWAYS
OF THE APPLIANCE BE KEPT
CLEAN.
BEFORE YOU START
Safe installation and operation of this appli-
ance requires common sense, however, we
arerequiredby theCanadianSafety Standards
andANSI Standards to make you aware of the
following:
1) Provide adequate clearances for servicing,
properoperationandaroundtheairopenings
into the combustion chamber.
2) The appliance must be installed on a flat,
solid,continuoussurface(e.g.wood,metal,
concrete).Thismaybethefloor,oritcanbe
raiseduponaplatformtoenhanceitsvisual
impact. The appliance may be installed on
carpeting, tile, wood flooring or other com-
bustible material, because the appliance's
baseextends thefullwidth anddepth ofthe
appliance. The Direct Vent Freestanding
GasStove canbeinstalledina widevariety
of ways and will fit nearly any room layout.
It may be installed in a recessed position,
framedoutintotheroom,oracrossacorner.
3) The Direct Vent Freestanding Gas Stove
is approved for alcove installations, which
meet the clearances listed on in the "Clear-
ance to Combustibles" section. This unit
is approved for manufactured home in-
stallations, see the "Manufactured Mobile
Home Additional Requirements" section
and "Venting Arrangements" section for
the required vent arrangements. If installed
into a manufactured home the unit must be
bolted down to the floor.
4) ThisapplianceisListedfor bedroom instal-
lations when used with a Listed Millivolt
CHILDREN AND ADULTS SHOULD
BE ALERTEDTOTHE HAZARDS OF
HIGH SURFACE TEMPERATURES,
ESPECIALLY THE FIREPLACE
GLASS, AND SHOULD STAY AWAY
TO AVOID BURNS OR CLOTHING
IGNITION.
DUETO HIGHTEMPERATURES,THE
APPLIANCE SHOULD BE LOCATED
OUT OFTRAFFIC AND AWAY FROM
FURNITURE AND DRAPERIES.
WARNING: FAILURE TO INSTALL
THIS APPLIANCE CORRECTLYWILL
VOID YOUR WARRANTY AND MAY
CAUSE A SERIOUS HOUSE FIRE.
YOUNG CHILDREN SHOULD BE
CAREFULLY SUPERVISED WHEN
THEY ARE IN THE SAME ROOM AS
THE APPLIANCE.
CLOTHING OR OTHER FLAMMA-
BLE MATERIAL SHOULD NOT BE
PLACED ON OR NEAR THE
APPLIANCE.

8Hampton®H27 Direct Vent Freestanding Gas Stove
INSTALLATION
Thermostat. Some areas may have further
requirements, check local codes before
installation.
5) This appliance is Listed for Alcove installa-
tions,maintainminimumAlcoveclearances
as follows, minimum width of 34-3/4"
(882mm),amaximumdepthof36"(914mm),
andminimumceilingheightof51"(1295mm)
from floor to ceiling.
6) We recommend that you plan your instal-
lation on paper using exact measurements
for clearances and floor protection before
actually installing this appliance. Have a
qualifiedbuildinginspectorreviewyourplans
before installation.
GENERAL SAFETY
INFORMATION
1) Theapplianceinstallationmustconformwith
local Canadian Electrical Code.
2) Theappliancewheninstalled,mustbeelec-
trically grounded in accordance with local
codes, or in the absence of local codes with
the current National Electrical Code, ANSI/
NFPA70 or CSAC22.1 Canadian Electrical
Code.
3) The applianceshouldbeinspectedforship-
ping damage before use and serviced an-
nually by a professional service person.
Morefrequentcleaningmayberequireddue
to excessive lint from carpeting, bedding
material, etc. It is imperative that control
compartments,andcirculating air passage-
waysoftheappliancebekeptcleanandfree
from excessive lint from carpeting.
4) See general construction and assembly
instructions.Theapplianceand ventshould
be enclosed when installed in or passing
through a living area, where children may
come in contact with it.
5) This appliance must be connected to the
specified vent and termination cap to the
outside of the building envelope. Never
vent to another room or inside a building.
Make sure that the vent is fitted as per the
instructions starting in the "Exterior Vent
Terminal Locations" section.
6) Inspect the venting system annually for
blockage and any signs of deterioration.
7) Venting terminalsshall not berecessed into
a wall or siding.
8) Anysafetyglassremovedforservicingmust
bereplacedpriortooperatingtheappliance.
9) To prevent injury, do not allow anyone who
is unfamiliar with the operation to use the
fireplace.
INSTALLATION
CHECKLIST
1) Locateyourappliance.Refertothefollowing
sections:
a. Clearances to Combustibles
b. Locating Your Gas Stove
c. For venting requirements, see "Venting
Introduction" to "Rigid Pipe Venting
Systems" sections.
2) Install Optional Fan. Refer to the "Optional
Fan Installation" section.
3) Set vent restrictor. Refer to the
"Vent Restrictor Position" section.
4) Install venting:
a. Check all venting requirements. See
"Vent Restrictor Position" to Rigid Pipe
Venting Systems" sections
b. Vertical Termination with Co-linear Flex
System
c. DV Stove Horizontal Vent Kit
d. Minimum Horizontal Termination
e. Dura-Vent Termination Kit
5) Make gas connections. Refer to the "Gas
Connection" section.
Testthe pilot.Must beas perdiagraminthe
"Maintenance Instruction" section.
If converting to Propane, make changes
prior.Refertothe "ConversionfromNatural
Gas to Propane" section.
6) Test Gas Pressure. Refer to the "Pressure
Testing" section.
7) Installstandardandoptionalfeatures.Refer
to the following sections where applicable:
a. Log Set Installation
b. Decorative Door Grill
c. Wall Thermostat
d. Remote Control
8) Final check. Refer to the "Final Check"
section.
Before leaving this unit with the customer, the
installer must ensure that the appliance is fir-
ing correctly and operation fully explained
to customer.
This includes:
1) Clockingtheappliancetoensurethecorrect
firingrate(ratenotedonlabel)afterburning
appliance for 15 minutes.
2) Ifrequired,adjustingtheprimaryairtoensure
that the flame does not carbon. First allow
the unit to burn for 15-20 min. to stabilize.
CAUTION:Any alterationtothe productthat
causes sooting or carboning that results
in damage is not the responsibility of the
manufacturer.
CLEARANCES TO
COMBUSTIBLES
Theclearanceslisted are MINIMUMdistances.
Measuretheclearancetoboththeapplianceand
thechimneyconnector.Thefarthestdistanceis
correctifthetwoclearancesdonotcoincide.
Forexample,iftheappliance issetas indicated
in one of the figures but the connector is too
close,movethestoveuntilthecorrectclearance
to the connector is obtained.
This appliance may be installed only with the
clearances as shown in the situations pictured.
Donotcombineclearancesfromonetypeof
installation with another in order to achieve
closer clearances.
Thisunitcanbeinstalledonasolidcombustible
surface like a wood floor. This unit can also be
installed directly on carpeting or vinyl.
Use the minimum clearances shown in the
diagrams below:
H27-NG & H27-LP Clearances
A Left Side Wall to Unit*6" / 150 mm
B Back Wall to Unit 3" / 75 mm
C Vertical Vent Pipe to Back Wall
2" / 50 mm
E Unit Corner to Wall 2" /50 mm
Unit Top to Alcove Ceiling 24" / 610 mm
Minimum ceiling height is 24" /610 mm from
top of unit.
Emissions from burning wood or gas could
contain chemicals known to the State of Cali-
fornia to cause cancer, birth defects or other
reproductive harm.

Hampton®H27 Direct Vent Freestanding Gas Stove 9
LOCATING YOUR
GAS STOVE
Whenselectingalocationforyourstove,ensure
that the clearances listed above are met as well
as ensuring that there is adequate accessibility
for servicing and proper operation.
MANUFACTURED
MOBILE HOME
ADDITIONAL
REQUIREMENTS
1) Ensurethat structural membersare notcut
or weakened during installation.
2) Ensure proper grounding using the #8
ground lug provided.
3) Appliance must be anchored to the floor
with the supplied anchoring methods.
COMBUSTION AND
VENTILATION AIR
Thecombustionairfromthisapplianceisdrawn
fromoutsidethebuildingthroughtheouterflue.
Extraprovisionforcombustionairinsidethe
room is not required.
A) Cross Corner
B) Room Divider
C) Island
D) Flat on Wall
E) Flat on Wall Corner
F) Flush with Wall/Alcove
For Vent Termination requirements,
see "Exterior Vent Terminal Locations"
section.
INSTALLATION
OPTIONAL FAN
INSTALLATION
Fan Kit Contains:
Qty. Description
1 Fan Assembly c/w green wire attached
1 Thermodisc
1 power cord
2 2-1/4" x 20 hex nut
1 Fan Speed Control
1) a) Remove the rear access panel on the
back of the stove by removing the 2 screws
under the rear panel.
2) Disconnect the red and grey wires.
Top Control Panel Assembly
Fan Speed
Controller
4) Removethenylonholeplugfromthecontrol
panel.
5) Install the fan speed controller onto the
control panel and secure with nut and
washer. Connect the red and black wires
from the wire harness to speed controller.
NOTE: Speed control wires must be in
thedown positionwhencontrol panelis
in place.
screw screw
Lift Rear Panel off the 2 top bolts
Bolts
3) Remove the Top Control Panel Assembly
by removing the three screws.
7) Re-attach control panel with 3 screws,
reversing step 3.
b) Lift off the 2 bolts at the top.
Take care not to cut wires when
lowering the panel.
6) Push black knob onto speed control.

10 Hampton®H27 Direct Vent Freestanding Gas Stove
INSTALLATION
8) Place the blower close to the base of the unit and feed the long red
and black wires through the opening of the base of the unit and the
short red and black wires through the small hole at the base of the
unit.
11) Mount the blower assembly in position under the base of the stove
and secure with the 2 supplied bolts (2-1/4" #20 hex head)
12) Before re-attaching the rear access panel, the valve wires and the
fan wires need to be connected.
Re-connect the red and grey valve wires.
13) Slide the Rear Access Panel back into position and secure with 2
screws.
Connect the fan wires.
WARNING: Electrical Grounding Instructions
This appliance is equipped with a three pronged (grounding) plug for your protection against shock hazard and should be
plugged directly into a properly grounded three-prong receptacle. Do not cut or remove the grounding prong from this plug.
9) Slide Thermodisc into the bracket on the left side of the rear fire-
box.
Thermodisc
Thermodisc
Braket

Hampton®H27 Direct Vent Freestanding Gas Stove 11
INSTALLATION
PRECAUTIONS
Theseventingsystemsareengineeredproducts
that have been designed and tested for use
with the H27-NG, and H27-LP. The warranty
will be voided and serious fire, health or other
safety hazards may result from any of the fol-
lowing actions:
1) Installation of any damaged Direct Vent
component
2) UnauthorizedmodificationoftheDirectVent
System
3) Installation of any component part not
manufactured byapprovedventingsystems
as per table on next page or FPI Fireplace
Products International Ltd.
4) Installation other than as instructed by
approved venting systems as per table
on next page and FPI Fireplace Products
International Ltd.
Warning: Alwaysmaintainrequired
clearances (air spaces) to nearby
combustibles to prevent a fire
hazard. Do not fill air spaces with
insulation.
Besuretochecktheventterminationclearance
requirements from decks, windows, soffits,
gas regulators, air supply inlets and public
walkways as specified in the "Exterior Vent
Terminal Locations" section and in your local
building codes.
The gas appliance and vent system must be
venteddirectlytotheoutsideofthebuilding,
and never be attached to a chimney serving
a separate solid fuel or gas-burning appli-
ance. Each direct vent gas appliance must use
it's own separate vent system. Common vent
systems are prohibited.
VENTING
INTRODUCTION
The Horizontal Termination Kit and other
approved venting systems as per table on
next page, in combination with the Direct Vent
Freestanding Gas Stoves, H27-NG, and H27-
LP, have been tested and listed as direct vent
heater systems by Warnock Hersey.
Theseunitsusethe"balanced flue" technology
Co-Axialsystem.Theinnerlinerventsproducts
ofcombustiontotheoutsidewhiletheouterpipe
draws outside combustion air into the combus-
tion chamber thereby eliminating the need to
use heated room air for combustion and losing
warm room air up the chimney.
Note: These flue pipes must not be
connected to any other appliance.
The gas appliance and vent system must be
vented directly to the outside of the building,
and never be attached to a chimney serving a
separate solid fuel or gas burning appliance.
Eachdirectventgasappliancemustuseit'sown
separate vent system. Common vent systems
are prohibited.
IMPORTANT
Read all instructions carefully before starting
the installation. Failure to follow these instruc-
tions may create a fire or other safety hazard,
and will void the warranty. Be sure to check the
venting and clearance to combustible require-
ments.Consultyourlocalbuildingcodesbefore
beginning installation.
The location of the termination cap must con-
form to the requirements in the "Exterior Vent
Terminal Locations" section.
SAFETY PRECAUTIONS
FOR THE INSTALLER
1) Wear gloves and safety glasses for protec-
tion.
2) Exercise extreme caution when using lad-
ders or on roof tops.
3) Be aware of electrical wiring locations in
walls and ceilings.
VENT RESTRICTOR
POSITION
To set the Vent restriction as indicated in the
diagrams in "Venting Arrangements" section,
simply loosen the screws and push the vent
restrictor plate to the correct position. Tighten
the screws.
INSTALLATION
ROTATING 45OELBOW
1) Removeall4 screwsthatsecure
the elbow to the unit using a 1/4"
magnetic nut driver.
2) Rotate the elbow 180o
3) Secure the elbow by securing
it with the 4 screws.
Remove all 4 screws
and washers

12 Hampton®H27 Direct Vent Freestanding Gas Stove
EXTERIOR VENT TERMINAL LOCATIONS
INSTALLATION
Minimum Clearance Requirements Canada1USA2
AClearance above grade, veranda, porch, deck, or balcony 12"(30cm) 12"(30cm)
BClearance to window or door that may be opened 12"(30cm) 9" (23cm)
CClearance to permanently closed window **
DVertical clearance to ventilated soffit located above the terminal within a horizontal distance of 2 feet (61cm)
from the center line of the terminal (check with the local code)
22"(56cm) 22"(56cm)
EClearance to unventilated soffit 12"(30cm) 12"(30cm)
FClearance to outside corner: with AstroCap and Vent Riser Termination Caps 6"(15cm) 6"(15cm)
Clearance to outside corner: with all other approved Termination Caps. 12"(30cm) 12"(30cm)
GClearance to inside corner: with AstroCap and Vent Riser Termination Caps 6"(15cm) 6"(15cm)
Clearance to inside corner: with all other approved Termination Caps 12"(30cm) 12"(30cm)
HClearance to each side of center line extended above meter/regulator assembly 36"(90cm)a*
JClearance to service regulator vent outlet 36"(90cm) *
KClearance to non-mechanical air supply inlet to building or the combustion air inlet to any other appliance 12"(30cm) 9" (23cm)
LClearance to a mechanical air supply inlet
#3' (91cm) above if within 10' (3m) horizontally.
72"(1.8m) 36"(90cm)b
MClearance above paved sidewalk or a paved driveway located on public property 84"(2.1m)┼*
NClearance under veranda, porch, deck, or balcony 12"(30cm)‡*
1In accordance with current CSA B149.1, Natural Gas and Propane Installation Code
2In accordance with the current ANSI Z223.1/NFPA 54, National Fuel Gas Code
┼A vent shall not terminate directly above a sidewalk or paved driveway which is located between two single family dwellings and serves both dwellings.
‡ Permitted only if veranda, porch, deck, or balcony is fully open on a minimum of two sides beneath the floor
*Clearance in accordance with local installation codes and the requirements of the gas supplier
a3 feet (91cm) within a height of 15 feet (4.5m) above the meter / regulator assembly
b3 feet (91cm) above - if within 10 feet (3m) horizontally

Hampton®H27 Direct Vent Freestanding Gas Stove 13
4” X 6-5/8” RIGID PIPE CROSS REFERENCE CHART
Components from different Manufacturers may not be mixed. Not All Rigid Pipe components are available directly from FPI.
Description Simpson
Direct Vent Pro®
Selkirk
Direct Temp™
American Metal
Products®
Amerivent Direct
Metal-Fab™
Sure Seal
Security
Secure- Vent®
ICC Excel
Direct
6” Pipe Length-Galvanized 46DVA-06 4DT-6 N/A 4D6 SV4L6 TC-4DL6
6” Pipe Length-Black 46DVA-06B 4DT-6B N/A 4D6B SV4LB6 TC-4DL6B
7” Pipe Length-Galvanized N/A N/A 4D7 N/A N/A N/A
7” Pipe Length-Black N/A N/A 4D7B N/A N/A N/A
9” Pipe Length-Galvanized 46DVA-09 4DT-9 N/A N/A N/A N/A
9” Pipe Length-Black 46DVA-09B 4DT-9B N/A N/A N/A N/A
12” Pipe Length-Galvanized 46DVA-12 4DT-12 4D12 4D12 SV4L12 TC-4DL1
12” Pipe Length-Black 46DVA-12B 4DT-12B 4D12B 4D12B SV4LB12 TC-4DL1B
18” Pipe Length-Galvanized 46DVA-18 4DT-18 4D18 4D18 SV4LA TC-4DL18
18” Pipe Length-Black 46DVA-18B 4DT-18B 4D18B 4D18B SV4LA TC-4DL18B
24” Pipe Length-Galvanized 46DVA-24 4DT-24 4D24 4D24 SV4L24 TC-4DL2
24” Pipe Length-Black 46DVA-24B 4DT-24B 4D24B 4D24B SV4LB24 TC-4DL2B
36” Pipe Length-Galvanized 46DVA-36 4DT-36 4D36 4D36 SV4L36 TC-4DL3
36” Pipe Length-Black 46DVA-36B 4DT-36B 4D36B 4D36B SV4LB36 TC-4DL3B
48” Pipe Length-Galvanized 46DVA-48 4DT-48 4D48 4D48 SV4L48 TC-4DL4
48” Pipe Length-Black 46DVA-48B 4DT-48B 4D48B 4D48B SV4LB48 TC-4DL4B
60” Pipe Length-Galvanized 46DVA-60 4DT-60 N/A N/A N/A N/A
60” Pipe Length-Black 46DVA-60B 4DT-60B N/A N/A N/A N/A
Adjustable Length 3”-10”-Galvanized N/A N/A N/A 4DAL N/A TC-4DLT
Adjustable Length 3”-10”-Black N/A N/A N/A 4DALB N/A TC-4DLTB
Adjustable Length 7”-Galvanized N/A N/A 4D7A N/A N/A N/A
Adjustable Length 7”-Black N/A N/A 4D7AB N/A N/A N/A
Extension Pipe 8-1/2”-Galvanized 46DVA-08A N/A N/A N/A N/A N/A
Extension Pipe 8-1/2”-Black 46DVA-08AB N/A N/A N/A N/A N/A
Adjustable Length 12”-Galvanized N/A N/A 4D12A N/A SV4LA12 N/A
Adjustable Length 12”-Black N/A N/A 4D12A N/A SV4LBA12 N/A
Extension Pipe 16”-Galvanized 46DVA-16A N/A N/A N/A N/A N/A
Extension Pipe 16”-Black 46DVA-16AB N/A N/A N/A N/A N/A
45ºElbow-Galvanized 46DVA-E45 4DT-EL45 4D45L N/A N/A TE-4DE45
45ºElbow-Black 46DVA-E45B 4DT-EL45B 4DT-EL45B N/A N/A TE-4DE45B
45ºElbow Swivel-Galvanized See 46DVA-E45 N/A N/A 4D45L SV4E45 N/A
45ºElbow Swivel-Black See 46DVA-E45B N/A N/A 4D45LB SV4EB45 N/A
90ºElbow-Galvanized 46DVA-E90 4DT-EL90S 4DT-EL90S N/A N/A TE-4DE90
90ºElbow-Black 46DVA-E90B 4DT-EL90SB 4DT-EL90SB N/A SV4EBR90-1 TE-4DE90B
90ºElbow, Swivel-Galvanized See 46DVA-E90 N/A N/A 4D90L SV4E90-1 N/A
90ºElbow, Swivel-Black See 46DVA-E90B N/A N/A 4D90LB SV4EB90-1 N/A
90º Starter Elbow, Swivel-Galvanized N/A N/A N/A 4D90A N/A N/A
Adaptor* N/A N/A N/A 4D90L N/A N/A
Ceiling Support N/A 4DT-CS 4DFSP 4DSP SV4SD TE-4DE45
Cathedral Support Box 46DVA-CS 4DT-CSS 4DRSB 4DRS SV4CSB TE-4DE45B
Wall Support/Band 46DVA-WS 4DT-WS/B 4DWS 4DWS SV4BM N/A
Offset Support 46DVA-ES (N/A - FPI) 4DT-OS N/A N/A SV4SU N/A
Wall Thimble-Black 46DVA-WT 4DT-WT 4DWT 4DWT SV4RSM TE-4DE90
Wall Thimble Support/Ceiling Support 46DVA-DC N/A N/A N/A SV4PF TE-4DE90B
Firestop Spacer 46DVA-FS 4DT-FS 4DFSP 4DFS SV4BF N/A
Trim Plate-Black N/A 4DT-TP 4DFPB 4DCP SV4LA N/A
INSTALLATION

14 Hampton®H27 Direct Vent Freestanding Gas Stove
INSTALLATION
Description Simpson
Direct Vent Pro®
Selkirk
Direct Temp™
American Metal
Products®
Amerivent Direct
Metal-Fab™
Sure Seal
Security
Secure- Vent®
ICC Excel
Direct
Attic Insulation Shield 12” 46DVA-IS N/A@ FPI N/A 4DAIS12 N/A SV4RSA N/A
Attic Insulation Shield - Cold Climates 36” N/A N/A 4DAIS12 N/A N/A TM-4AS
High Wind Vertical Cap 46DVA-VCH N/A N/A N/A N/A TM-4VT
High Wind Horizontal Cap 46DVA-HC N/A N/A N/A N/A TM-4DHT
Horizontal Square Termination Cap See 46DVA-HC 4DT-HHC 4DHC 4DHT SV4CHC-1 TM-4HT
Vertical Termination Cap N/A 4DT-HVC 4DVC 4DVT SV4CGV-1 TM-4VT
Storm Collar 46DVA-08A 4DT-SC 4DSC 4DSC SV4FC TM-SC
Restrictor Disk 46DVA-RD N/A N/A N/A N/A TM-4DS
Extended Vertical Termination Cap 46DVA-VCE N/A N/A N/A N/A N/A
Chimney Conversion Kit A (USA only) 46DVA-KCA N/A N/A N/A N/A TM-4CA6
Chimney Conversion Kit B (USA only) 46DVA-KCB N/A N/A N/A N/A TM-4CA7
Chimney Conversion Kit C (USA only) 46DVA-KCC N/A N/A N/A N/A TM-4CA8
Chimney Conversion Kit Masonry
(USA only)
46DVA-KMC N/A N/A N/A N/A N/A
Wall Firestop 46DVA-WFS N/A N/A N/A N/A TM-4TR
Colinear Flex Connectors 46DVA-ADF N/A N/A N/A N/A N/A
Adjustable Flashing 0/12-6/12 N/A 4DT-ST14 4D12S 4DST14 SV4STC14 TF-4FA
Adjustable Flashing 6/12-12/12 N/A 4DT-ST36 4D36S 4DST36 SV4STC36 TF-4FB
Vinyl Siding Standoff 46DVA-VSS 4DT-VS N/A 4DVS SV4VS TM-VSS
Vinyl Siding Shield Plate N/A 4DT-VSP N/A N/A SV4VS N/A
Snorkel Termination 14” 46DVA-VCH N/A N/A N/A N/A TM-4ST14
Snorkel Termination 36” 46DVA-HC N/A N/A N/A N/A TM-4ST36
Basic Horizontal Termination Kit (A) Disc. 4DT-HKA 4DHTK2 4DHTKA SV-SHK N/A
Horizontal Termination Kit (B) 46DVA-KHA
(Changed Components)
4DT-HKB 4DHTK1 4DHTKB SV-HK N/A
Vertical Termination Kit Disc. 4DT-VKC 4DHTK 4DHTK SV-FK N/A
FPI
946-506/P Vent Guard (Optional) for AstroCap 946-205 Vinyl Siding Shield for Riser Vent Terminal
510-994 Rigid Pipe Adaptor (Must use with all rigid piping) 946-208/P Vent Guard (Optional) for Riser Vent Terminal
640-530/P Riser Vent Terminal 946-523/P AstroCap Horizontal Cap
946-605 Starter Collar Increaser 4” x 6-5/8” to 5” x 8” 946-206 Vinyl Siding Standoff for AstroCap
Note: When using Metal-Fab Sure Seal Rigid Piping - please note that the Adaptor (4DDA) must be used in conjunction with FPI Rigid Pipe Adaptor (510-994).
Note: Horizontal runs of vent must be level, or have a 1/4” rise for every 1 foot of run towards the termination.
Never allow the vent to run downward - this could cause high temperatures and may present a possible fire hazard.
Offset Pipe Selection: Use this table to determine offset pipe lengths.
Pipe Length
(L)
4” x 6-5/8” Venting For specific instructions on venting components - visit the
manufacturers website listed below.
Run (X) Rise (Y)
0” (0mm) 4-7/8” (124mm) 13-7/8” (340mm) Simpson Direct Vent Pro: www.duravent.com
6” (152mm) 8” (203mm) 16-1/2” (419mm) Selkirk Direct-Temp: www.selkirkcorp.com
9” (229mm) 10-1/8” (257mm) 18-5/8” (473mm) American Metal Products: www.americanmetalproducts.com
12” (305mm) 12-1/4” (311mm) 20-3/4” (527mm) Metal-Fab Sure Seal: www.mtlfab.com
24” (610mm) 20-5/8” (524mm) 29-1/8” (740mm) Security Secure Vent: www.securitychimneys.com
36” (914mm) 29” (737mm) 37-1/2” (953mm) Industrial Chimney Company: www.icc-rsf.com
48” (1219mm) 37-7/16” (951mm) 45-15/16” (1167mm)

Hampton®H27 Direct Vent Freestanding Gas Stove 15
Pipe Length
Vertical
Termination
Cap
Storm Collar
Flashing
Ceiling Firestop
Pipe
Length
Adj.Pipe Length
90 Elbow
o
Horizontal
Termination
Cap
Wall Thimble
Vinyl Siding
Standoff (Optional)
RIGID PIPE VENTING SYSTEMS
Horizontal or Vertical Terminations
Alternate
Horizontal
Termination
Caps
INSTALLATION
When using Rigid Vent other than
Simpson Dura-Vent, 3 screws must be
used to secure rigid pipe to adaptor.
The FPI AstroCapTM and FPI Riser Vent terminal are certified for installations using FPI venting systems as well as Simpson Dura-Vent®Direct Vent,
American Metal Products Ameri Vent Direct Vent, Security Secure Vent®, Selkirk Direct-Temp and ICC Excel. AstroCapTM is a proprietary trademark of
FPI Fireplace Products International Ltd. Dura-Vent® and Direct Vent Pro are registered and/or proprietary trademarks of Simpson Dura-Vent Co. Inc.
This product has been evaluated by Intertek
for using a Rigid Pipe Adaptor in conjunction
with Duravent Direct-Vent Pro, Selkirk Direct-
Temp, Ameri Vent Direct, ICC Excel venting
and Security Secure Vent systems. Use of
these systems with the Rigid Pipe adaptor is
deemed acceptable and does not affect the
Intertek WHI listing of components.
WARNING:
Do not combine venting components from
different venting systems.
However use of the the AstroCapTM and FPI
Riser is acceptable with all systems.

16 Hampton®H27 Direct Vent Freestanding Gas Stove
INSTALLATION
Offset to Vertical Terminations
Venting Arrangements - Horizontal Terminations using Dura-Vent venting system
and/or Riser Vent Termination
Snorkel Termination Riser Vent Termination
VENTING ARRANGEMENTS
Vertical Terminations Systems for
Residential Manufactured and Mobile Homes
Theshadedareain the diagrambelowshowsallallowablecombinations of straight
vertical and offset to vertical runs with vertical terminations. Maximum two 45o
elbows.
If the vent is ENCLOSED in a chase (min. size 9" x 9") maintain a 1-1/4" clearance to
combustibles.
May be installed in Manufactured (Mobile) Homes after first sale.
Horizontal Terminations for
All Venting Systems
The shaded areas in the diagram below show all
allowable combinations of vertical runs with hori-
zontal terminations. Maximum one 90Oelbow (two
45o elbows equal one 90oelbow).
Propane and Natural Gas:
Residential, Manufactured and Mobile
Homes Installations
May be installed in Manufactured (Mobile) Homes
after first sale.
The two diagrams show all allowable com-
binationsofstraighthorizontal termination
withone45oelbowofftheunitwithSnorkels
or FPI Riser Vent. Restrictor position "A".

Hampton®H27 Direct Vent Freestanding Gas Stove 17
INSTALLATION
Horizontal Venting with Two (2) 90oElbows
Option V H + H1
A) 2' Min. 4' Max.
B) 3' Min. 5' Max.
C) 4' Min. 6' Max.
D) 5' Min. 7' Max.
E) 6' Min. 8' Max.
Horizontal Venting with Two (2) 90oElbows
Option H V H + H1
A) 1' Max. 1' Min. 3' Max.
B) 2' Max. 2' Min. 5' Max.
C) 3' Max. 4' Min. 6' Max.
D) 4' Max. 6' Min. 7' Max.
E) 5' Max. 8' Min. 8' Max.
With these options, max.
total pipe length is 30 feet
with min. of 8 feet total
vertical and max. 8 feet
total horizontal.
Please note min. 1 foot
between 90oelbows is
required.
With these options, maxi-
mum total pipe length is 30
feet with minimum of 6 feet
totalvertical and maximum
8 feet total horizontal.
Please note minimum 1
foot between 90oelbows
is required.
One 90oelbow = Two 45oelbows.
One 90oelbow = Two 45oelbows.
H
H1
V
Vent restrictor position A(fully open), refer to the
"Vent Restrictor Position" section.
Vent restrictor position A(fully open), refer to the "Vent
Restrictor Position" section.
Lengths do not include elbow indicated
Lengths do not include elbow indicated

18 Hampton®H27 Direct Vent Freestanding Gas Stove
Vertical Venting with Two (2) 90oElbows
Option V H V + V1
A) 1' Min. 4' Max. 2' Min.
B) 2' Min. 5' Max. 3' Min.
C) 3' Min. 6' Max. 4' Min.
D) 4' Min. 7' Max. 5' Min.
E) 5' Min. 8' Max. 6' Min.
Vertical Venting with Two (2) 90oElbows
With these options, max. total
pipelengthis30feetwithmin.
of6feettotalverticalandmax.
8 feet total horizontal.
Please note min. 1 foot
between 90oelbows is re-
quired.
Option H + H1 V
A) 2' Max. 2' Min.
B) 3' Max. 3' Min.
C) 4' Max. 4' Min.
D) 5' Max. 5' Min.
E) 6' Max. 6' Min.
Withtheseoptions,max.total
pipelengthis30feetwithmin.
of6feettotalverticalandmax.
6 feet total horizontal.
Please note min. 1 foot
between 90oelbows is
required.
One 90oelbow = Two 45oelbows.
One 90oelbow = Two 45oelbows.
V1
V
H
Vent restrictor position A(fully open), refer to the "Vent
Restrictor Position" section.
Vent restrictor position A(fully open), refer to the "Vent
Restrictor Position" section.
Lengths do not include elbow indicated
Lengths do not include elbow indicated
INSTALLATION

Hampton®H27 Direct Vent Freestanding Gas Stove 19
Flex Liner
Exhaust
Flue
A maximum
of two certified
joiner kits
may be used
per length.
#948-305 (35 ft)
Air Intake
Co-linear DV
Vertical Termination
Cap # 946-529
Co-Linear
Flex
Adapter
with Kit#
946-563
Outer
Pipe
with Kit#
946-563
Inner Pipe
Adapter
with Kit#
946-563
Venting Arrangements - Vertical Terminations
with Co-linear Flex System for both
Residential & Manufactured Homes
into Masonry Fireplaces
The shaded area in the diagram shows the allowable vertical
terminations. Note: Must remove 4 screws from stove collar
androtate 130oto havecollarfacing straightback.Secure into
place with 4 screws.
VERTICAL TERMINATION WITH CO-LINEAR FLEX SYSTEM
This appliance is designed to be attached to
two 3" (76mm) co-linear aluminium flex running
the full length of the chimney. See the Venting
Arrangements chart below for minimum and
maximum flue lengths. See chart below for
minimumdistancesfromroof.Periodicallycheck
that the vent is unrestricted.
Masonrychimneysmaytakevariouscontourswhichthe flexiblelinerwill accommodate.However,
keep the flexible liner as straight as possible, avoid unnecessary bending.
The Air Intake pipe must be attached to the inlet air collar of the termination cap.
Straight Vertical Terminations
INSTALLATION
Required Parts:
Part # Description
946-529 Co-linear DV Vertical
Termination Cap
948-305 3" Flex - 35 ft.
946-563 Co-Axial to Co-Linear Adapter Kit
which contains the following:
Co-linear Flex Adapter (270-585)
Outer Pipe (946-257)
Inner Pipe Adapter (946-219)
Vent Restrictors
set at fully open,
Posiiton "A"
THE APPLIANCE MUST NOT BE
CONNECTED TO A CHIMNEY FLUE
SERVING A SEPARATE SOLID FUEL
BURNING APPLIANCE.

20 Hampton®H27 Direct Vent Freestanding Gas Stove
DV STOVE HORIZONTAL VENT KIT (#946-116 & #946-216) INSTALLATION
Review the following sequence of instructions
which are typical of most installations. The se-
quence may vary depending on wall thickness.
See the "Exterior Vent Terminal Locations"
section for vent location and clearance
dimensions, and "Vent Restrictor Position"
section to set the Vent Restrictor to the
correct position.
1) Set the unit in its desired location. Check
to determine if wall studs will be in the way
of the venting system, adjust location until
all clearances are met and there are no
obstructions.
Note: A1-1/2"(38mm)clearancearoundthe
outerpipemustbemaintainedexcept
that only a 1" (25mm) clearance is
needed at the termination end.
IMPORTANT:
Do not locate termination hood where
excessive snow or ice buildup may
occur. Be sure to check vent termina-
tion area after snow falls, and clear to
preventaccidental blockageofventing
system. When using snow blowers,
makesuresnowisnotdirectedtowards
vent termination area.
b) Install wall thimbles on both interior
and exterior wall with 4 wood screws
(#8 x 1") per thimble.
c) Attachthe2pieceadjustablepipesec-
tion to the vent terminal and slide into
position from the exterior. The larger
diameterendof the adjustablepipe
goes to the vent terminal.
d) Install the 90oelbow onto the adjust-
able pipe to determine the vertical
centerline.
Note:ifthecenterlinecannotbemet,
theadjustable sectionswill haveto
be cut.
e) Cut the 4 ft. section of rigid pipe to
length.Attachthe 45oelbowtotherigid
pipe, and ensure that the pipe length
whencut (withthe45oelbow)willseat
ontoboththe startercollarandthe 90o
elbow. Crimpedsectionofrigidpipe
seats into the 90oelbow. Only cut
the uncrimped side of pipe.
Dismantle all pipe sections including vent
terminal.
2) Assembleatrialfittodeterminethevertical
centerline for the vent termination.
a) Cut a 9-1/2" x 9-1/2" (241mm x 241
mm) square hole on both the interior
and exterior wall.
Adapter
Trim Collar
4" ID Liner
Spacer
Spring
Thimble
Cover Termination Cap
(Part# 946-523/P)
AstroCap
Wall Thimble
(required for
combustible walls)
Adjustable Pipe
Length 13-1/2" - 24",
2 pieces
4 ft. Pipe Length
with Kit # 946-216
or 2 ft. Pipe Length with
Kit # 946-116
Trim
Collar
INSTALLATION
DV STOVE HORIZONTAL VENT KIT
DV 2 ft. Stove Vent Kit (Part # 946-116) and DV 4 ft. Stove Vent Kit (946-216) includes all the parts needed
to install the H27 Direct Vent unit with minimum horizontal and vertical vent dimensions. For installations
that require longer vertical and/or horizontal vents use the Dura-Vent system as shown in the "Dura-Vent
Termination Kit" and "Dura-Vent Venting Components" sections.
Qty. Description
1) 1 Rigid Pipe Section (Kit # 946-116: 2 ft. (1.2m) length,
Kit # 946-216: 4 ft. (1.2m) length), 6-1/2" (165mm)
inside diameter
2) 1 Flex Liner, compressed aluminium 2 ply liner, 4" (102mm)
inside diameter
3) 4 spring spacers
4) 1 90 deg. Elbow
5) 1 Adjustable pipe section 13-1/2" to 24" (343mm x 610mm), 2 pcs.
6) 1 Thimble Cover
7) 1 Wall Thimble (2 pcs.)
8) 1 Adapter
9) 1 AstroCap Termination Cap
10) 2 Trim Collars
11) 1 Tube of Mill-Pac, high temperature sealant
12) 12 Screws, #8 x 1/2" Self tapping, Stainless Steel
13) 14 Screws, #8 x 1/2" Self tapping, Black
14) 4 Screws #8 x 1-1/2" Drill Point, Black
15) 4 Screws #8 x 1-1/2" Drill Point, Stainless Steel
16) 8 Wood screws #8 x 1"
Note:
a) Liner sections should be con-
tinuous without any joints or
seams.
b) Thisisanapprovedsystem,there-
fore components in this system
must not be substituted for any
other manufacturer's products.