HAMPTON BAY H35-NG2 Quick start guide

FPI FIREPLACE PRODUCTS INTERNATIONAL LTD. 6988 Venture St., Delta, BC Canada, V4G 1H4
WARNING:
If the information in these instructions are not followed ex-
actly,afireorexplosionmayresultcausingpropertydamage,
personal injury or loss of life.
FOR YOUR SAFETY
Do not store or use gasoline or other flammable vapors and
liquids in the vicinity of this or any other appliance.
Installation and service must be performed by a qualified
installer, service agency or the gas supplier.
FOR YOUR SAFETY
What to do if you smell gas:
Do not try to light any appliance
Do not touch any electrical switch:
do not use any phone in your
building.
Immediately call your gas supplier
from a neighbour's phone. Follow
the gas supplier's instructions.
If you cannot reach your gas
supplier, call the fire department.
918-838
MODELS: H35-NG2 Natural Gas H35-LP2 Propane
07/19/11
H35 Direct Vent Gas Fireplace
H35 Direct Vent Gas Fireplace
Owners &
Installation Manual
Tested by: Installer: Please complete the details on the back cover
and leave this manual with the homeowner.
Homeowner: Please keep these instructions for future reference.
www.hampton-fire.com

2Hampton® H35-2 Direct Vent Freestanding Gas Stove
HAMPTON®
Direct Vent Freestanding Gas Stove
To the New Owner:
Congratulations!
You are the owner of a state-of-the-art Hampton®Gas Stove by REGENCY FIREPLACE PRODUCTS .
The H35-2 is a hand crafted appliance and has been designed to provide you with all the warmth and charm of a wood fireplace
at the flick of a switch. The model H35-2 has been approved by Warnock Hersey for both safety and efficiency. As it also bears
our own mark, it promises to provide you with economy, comfort and security for many trouble free years to follow. Please take a
moment now to acquaint yourself with these instructions and the many features of your
Hampton® Stove.

Hampton® H35-2 Direct Vent Freestanding Gas Stove 3
DIMENSIONS
UNIT DIMENSIONS
* Unit shown with optional side shelves.
25” (835mm)
15-3/8” (391mm)
16-3/4” (425mm)
26-1/4” (667mm)
28” (711mm)
38-1/4” (972mm)
26-7/8” (683mm)
21” (533mm)

4Hampton® H35-2 Direct Vent Freestanding Gas Stove 444
TABLE OF CONTENTSTABLE OF CONTENTS
Optional Brick Panel....................................................35
Log Set Installation......................................................35
Double DoorRemoval..................................................36
Optional side shelves installation ................................37
Wiring Diagrams..........................................................38
Wall Thermostat ..........................................................39
Remote Control ..........................................................39
OPERATING INSTRUCTIONS
Operating Instructions .................................................40
Lighting Procedure ......................................................40
Shutdown Procedure...................................................40
First Fire ......................................................................40
Final Check..................................................................40
Copy of the Lighting Plate Instructions .......................41
Adjusting Flame Height ...............................................41
Automatic Convection Fan Operation..........................41
Normal Operating Sounds of Gas Appliances.............42
MAINTENANCE
Maintenance Instructions.............................................42
General Vent Maintenance..........................................43
Log Replacement ........................................................43
Glass Replacement.....................................................43
Fan Maintenance.........................................................43
Removing Valve...........................................................44
Installing Valve Assembly............................................44
PARTS
Main Assembly ............................................................45
Burner & Log Assembly...............................................46
WARRANTY
Warranty......................................................................47
DIMENSIONS
Unit Dimensions ............................................................3
SAFETY LABEL
Copy of Safety Label.....................................................5
REQUIREMENTS
Specifications ................................................................7
Information for Mobile Homes After First Sale...............7
INSTALLATION
General Safety Information............................................9
Installation Checklist......................................................9
Clearances to Combustibles..........................................9
Locating YourGas Stove..............................................10
Manufactured Mobile Home Additional Requirements 10
Combustion and Ventilation Air....................................10
Optional Fan Installation..............................................10
Venting Introduction.....................................................11
Installation Precautions ...............................................11
Safety Precautions for The Installer ............................11
Vent Restrictor Position...............................................11
Exterior Vent Terminal Locations.................................12
4” x 6-5/8” Rigid Pipe ..................................................13
Cross Reference Chart only........................................13
Rigid Pipe Venting Systems ........................................15
45oElbow for Straight Horizontal Terminations ...........16
Venting Arrangements.................................................16
Vertical Termination With Co-linear Flex System.........20
DV Stove Horizontal Termination Vent Kit...................21
Dura-Vent Termination Kit............................................23
Horizontal Installations ................................................24
Rigid Vent system........................................................24
Vertical Termination.....................................................25
Rigid Vent system........................................................25
Converting Chimney to Direct Vent System ................27
Cathedral Ceilings.......................................................28
High Elevation .............................................................28
Gas Connection...........................................................28
Aeration Adjustment ....................................................29
Gas Pipe Pressure Testing..........................................29
Conversion from NG to LP ..........................................30
Conversion Kit to Lower BTU Rating...........................34

Hampton® H35-2 Direct Vent Freestanding Gas Stove 5
SAFETY LABEL
This is a copy of the label that accompanies
each Direct Vent Freestanding Gas Stove.
We have printed a copy of the contents here
for your review.
NOTE:Hampton®unitsareconstantlybeing
improved. Check the label on the unit and if
there is a difference, the label on the unit is
the correct one.
COPY OF SAFETY LABEL
Listed: VENTED GAS FIREPLACE HEATER /
FOYER AU GAZ À ÉVACUATION
Certified for/Certifiée pour: CANADA and U.S.A.
WN# 16478
Tested to: CGA 2-17-M91, ANSIZ21.88a-2007/CSA 2.33a-2007
MAY BE INSTALLED IN MANUFACTURED (MOBILE) HOMES AFTER FIRST SALE
DO NOT REMOVE THIS LABEL / NE
PAS ENLEVER CETTE ÉTIQUETTE
Minimum supply pressure
Manifold pressure High
Manifold pressure Low
Maximum Input
Minimum Input
Orifice size
Altitude
Minimum supply pressure
Manifold pressure High
Manifold pressure Low
Maximum Input
Minimum Input
Orifice size
Altitude
5" WC/C.E. (1.25 kPa)
3.8" WC/C.E. (0.94 kPa)
1.1" WC/C.E. (0.27 kPa)
36,000 Btu/h (10.55 Kw/h)
18,000 Btu/h (5.28 Kw/h)
#33 DMS (2.87mm)
0-4500 ft/pi (0-1372m)
Pression d'allimentation minimum
Pression à la tubulure d'échappement élevée
Pression à la tubulure d'échappement basse
Débit Calorifique maximum
Débit Calorifique minimum
Dimensions de l’orifice
L’altitude
Pression d'allimentation minimum
Pression à la tubulure d'échappement élevée
Pression à la tubulure d'échappement basse
Débit Calorifique maximum
Débit Calorifique minimum
Dimensions de l’orifice
L’altitude
FACTORY EQUIPPED FOR NATURAL GAS Model:H35-NG2
Convertible to 30,000
Orifice Size
Maximum Input
Minimum Input
Altitude
#37 DMS
30,000 Btu/h (8.78 Kw/h)
14,300 Btu/h (4.19 Kw/h)
0-4500 ft/pi (0-1372m)
Dimensions de l'orifice
Débit Calorifique maximum selon
Débit Calorifique minimum selon
L’altitude
Dimensions de l'orifice
Débit Calorifique maximum selon
Débit Calorifique minimum selon
L’altitude
FACTORY EQUIPPED FOR PROPANE GAS Model:H35-LP2
12" WC/C.E. (3.00 kPa)
11" WC/C.E. (2.74 kPa)
2.9" WC/C.E. (0.72 kPa)
34,000 Btu/h (9.97 Kw/h)
17,500 Btu/h (5.13 Kw/h)
#51 DMS (1.70mm)
0-4500 ft/pi (0-1372m)
Convertible to 28,500 Btu
Orifice Size
Maximum Input
Minimum Input
Altitude
This appliance must be installed in accordance with local codes, if any; if none, follow the National Fuel Gas Code, ANSI Z223.1, or Natural Gas
and Propane Installation Code, CSA B149.1.
This appliance must be installed in accordance with the Standard CAN/CSA Z240 MH, Mobile Housing, in Canada, or with the Manufactured
Home Construction and Safety Standard, Title 24 CFR, Part 3280, in the United States, or when such a standard is not applicable, ANSI/NCS-
BCS A225.1/NFPA 501A, Manufactured Home Installations Standard or ANSI A119.2 ou NFPA 501C Standard for Recreational Vehicles
This appliance is only for use with the type of gas indicated on the rating plate and may be installed in an aftermarket, permanently located,
manufactured (mobile) home where not prohibited by local codes. See owner's manual for details.
Installer l'appareil selon les codes ou règlements locaux, ou, en l'absence de tels règlements, selon les codes d'installation ANSI Z223.1, Na-
tional Fuel Gas Code ou CSA-B149.1 en vigueur.
Installer l'appareil selon la norme CAN/CSA-Z240, Série MM, Maison mobiles ou CAN/CSA-Z240 VC, Véhicules de camping, ou la norme 24
CFR Part 3280, Manufactured Home Construction and Safety Standard. Si ces normes ne sont pas pertinentes, utilisez la norme ANSI/NCS-
BCS A225.1/NFPA 501A, Manufactured Home Installations Standard, ou ANSI A119.2 ou NFPA 501C Standard for Recreational Vehicles.
Cet appareil doit être utilize uniquement avec le type de gaz indiqué sur la plaque signalétique. Cet appareil peut être installé dans une maison
préfabriquée ou mobile (É.-U. seulement) installée à demeure si les règlements locaux le permettent. Voir la notice de l'utilisateur pour plus de
renseignements. Cet appareil ne peut pas être utilisé avec d'autres gaz sauf si une trousse de conversion certifiée est fournie.
This vented gas fireplace heater is not for use with air filters. Ne pas utiliser de filtre à air avec ce foyer au gaz à évacuation.
For use with glass doors certified with the appliance only Pour utilisation uniquement avec les portes en verre certifiées avec l'appareil
Electrical supply / Électrique 115VAC, 1.13 A, 60Hz.
NOT FOR USE WITH SOLID FUELS. / NE PAS UTILISER AVEC DU COMBUSTIBLE SOLIDE
FPI Fireplace Products International Ltd. Delta, BC, Canada Made in Canada/Fabrique au Canada 918-840
Minimum Clearances to Combustibles/Degagement
Minimum De Materiaux Combustibles
Minimum ceiling height from top of unit:36”/914mm
Minimum plafond hauteur en haut de l’appareil:
A 6-1/2”/165mm
B 6”/152mm
Minimum clearance of Vent Terminal to Outside Corner & Inside Corner:
with AstroCap 6"/150mm with Dura-Vent Cap 12"/300mm
C 2" / 50mm
E 2"/50mm
Serial No./ No de serie
E
E
A
A
Left Side Wall
Right Side Wall
Vertical
Pipe
A
A
BC
Left Side Wall
Right Side Wall
Horizontal
Pipe
Model/Modele: H35-NG2
Model/Modele:
H35-LP2
355
355
#52 DMS
28,500 Btu/h (8.35 Kw/h)
15,000 Btu/h (4.39 Kw/h)
0-4500 ft/pi (0-1372m)
ÉQUIPÉ A L'UISINE POUR GAZ NATURAL
ÉQUIPÉ A L'UISINE POUR GAZ PROPANE
DUPLICATE SERIAL NO.
For the State of Massachusetts, installation and repair must be done by a plumber or gasfitter licensed in the Commonwealth of
Massachusetts.
For the State of Massachusetts, flexible connectors shall not exceed 36 inches in length.
For the State of Massachusetts, the appliances individual manual shut-off must be a t-handle type valve.
The State of Massachusetts requires the installation of a carbon monoxide alarm in accordance with NFPA720 and a CO alarm with
battery back up in the same room where the gas appliance is installed.

6Hampton® H35-2 Direct Vent Freestanding Gas Stove
REQUIREMENTS
5.08: Modifications to NFPA-54, Chapter 10
(2) Revise 10.8.3 by adding the following additional requirements:
(a) For all side wall horizontally vented gas fueled equipment installed in every dwelling, building or structure used in whole or in part for
residential purposes, including those owned or operated by the Commonwealth and where the side wall exhaust vent termination is less than
seven (7) feet above finished grade in the area of the venting, including but not limited to decks and porches, the following requirements shall
be satisfied:
1. INSTALLATION OF CARBON MONOXIDE DETECTORS. At the time of installation of the side wall horizontal vented gas fueled
equipment, the installing plumber or gasfitter shall observe that a hard wired carbon monoxide detector with an alarm and battery back-up is
installed on the floor level where the gas equipment is to be installed. In addition, the installing plumber or gasfitter shall observe that a battery
operated or hard wired carbon monoxide detector with an alarm is installed on each additional level of the dwelling, building or structure
served by the side wall horizontal vented gas fueled equipment. It shall be the responsibility of the property owner to secure the services of
qualified licensed professionals for the installation of hard wired carbon monoxide detectors
a. In the event that the side wall horizontally vented gas fueled equipment is installed in a crawl space or an attic, the hard wired carbon
monoxide detector with alarm and battery back-up may be installed on the next adjacent floor level.
b. In the event that the requirements of this subdivision can not be met at the time of completion of installation, the owner shall have a period of
thirty (30) days to comply with the above requirements; provided, however, that during said thirty (30) day period, a battery operated carbon
monoxide detector with an alarm shall be installed.
2. APPROVED CARBON MONOXIDE DETECTORS. Each carbon monoxide detector as required in accordance with the above provisions
shall comply with NFPA 720 and be ANSI/UL 2034 listed and IAS certified.
3. SIGNAGE. A metal or plastic identification plate shall be permanently mounted to the exterior of the building at a minimum height of eight
(8) feet above grade directly in line with the exhaust vent terminal for the horizontally vented gas fueled heating appliance or equipment. The
sign shall read, in print size no less than one-half (1/2) inch in size, "GAS VENT DIRECTLY BELOW. KEEP CLEAR OF ALL
OBSTRUCTIONS".
4. INSPECTION. The state or local gas inspector of the side wall horizontally vented gas fueled equipment shall not approve the installation
unless, upon inspection, the inspector observes carbon monoxide detectors and signage installed in accordance with the provisions of 248 CMR
5.08(2)(a)1 through 4.
(b) EXEMPTIONS: The following equipment is exempt from 248 CMR 5.08(2)(a)1 through 4:
1. The equipment listed in Chapter 10 entitled "Equipment Not Required To Be Vented" in the most current edition of NFPA 54 as adopted by
the Board; and
2. Product Approved side wall horizontally vented gas fueled equipment installed in a room or structure separate from the dwelling, building or
structure used in whole or in part for residential purposes.
(c) MANUFACTURER REQUIREMENTS - GAS EQUIPMENT VENTING SYSTEM PROVIDED. When the manufacturer of Product
Approved side wall horizontally vented gas equipment provides a venting system design or venting system components with the equipment, the
instructions provided by the manufacturer for installation of the equipment and the venting system shall include:
1. Detailed instructions for the installation of the venting system design or the venting system components; and
2. A complete parts list for the venting system design or venting system.
(d) MANUFACTURER REQUIREMENTS - GAS EQUIPMENT VENTING SYSTEM NOT PROVIDED. When the manufacturer of a
Product Approved side wall horizontally vented gas fueled equipment does not provide the parts for venting the flue gases, but identifies
"special venting systems", the following requirements shall be satisfied by the manufacturer:
1. The referenced "special venting system" instructions shall be included with the appliance or equipment installation instructions; and
2. The "special venting systems" shall be Product Approved by the Board, and the instructions for that system shall include a parts list and
detailed installation instructions.
(e) A copy of all installation instructions for all Product Approved side wall horizontally vented gas fueled equipment, all venting instructions,
all parts lists for venting instructions, and/or all venting design instructions shall remain with the appliance or equipment at the completion of
the installation.
MA Code - CO Detector
(for the State of Massachusetts only)

Hampton® H35-2 Direct Vent Freestanding Gas Stove 7
INSTALLATION
IMPORTANT MESSAGE
SAVE THESE
INSTRUCTIONS
The Direct Vent Freestanding Gas Stove must
be installed in accordance with these instructions.
Carefullyreadalltheinstructionsinthismanualfirst.
Consult the building authority having jurisdiction
to determine the need for a permit prior to starting
the installation.
Note: Failure to follow the instructions could
causeamalfunctionoftheheaterwhich
could result in death, serious bodily
injury,and/orpropertydamage. Failure
to follow these instructions may also
voidyourfireinsuranceand/orwarranty.
Note:Theseinstructionstakeprecedenceover
Simpson Dura-Vent instructions.
SPECIFICATIONS
Fuels: H35-NG2isapprovedforusewithnatural
gas.
H35-LP2 is approved for use with
liquefied petroleum gases (propane).
Electrical: 120V A.C. system.
Circulation Fan: Variable speed, 125/75.
Log Sets: Ceramic fibre, 7 per set.
VentSystem: Coaxial(6-5/8"outer/4"innerliner)
rigid flue and termination cap.
The efficiency rating of the appliance is a
product thermal efficiency rating determined
under continuous operating conditions and was
determined independent of any installed system.
INFORMATION FOR
MOBILE /
MANUFACTURED HOMES
AFTER FIRST SALE
ThisHampton®producthasbeentestedandlistedby
ITSTestingServicesas aDirect Vent WallFurnace
to the following standards:
CGA-2.17-M91, and ANSI Z21.88b-2007/CSA
2.33b-2007.
This Direct Vent System Appliance must be
installed in accordance with the manufacturer's
installationinstructionsandtheManufacturedHome
Construction and Safety Standard, Title 24 CFR,
Part 3280, or the current Standard of Fire Safety
Criteria for Manufactured Home Installations,
Sites, and Communities ANSI/NFPA 501A, and
with CAN/CSA Z240-MH Mobile Home Standard
in Canada.
This appliance installation must comply with the
manufacturer's installation instructions and local
codes, if any. In the absence of local codes follow
the current National Fuel Gas Code,ANSI Z223.1
andthecurrentNationalElectricalCodeANSI/NFPA
70inthe U.S.A., and the current CAN/CSAB149.1
Gas Installation Code and the current Canadian
Electrical Code CSA C22.1 in Canada.
ThisHampton®Mobile/ManufacturedHome
Listed appliance comes factory equipped
with a means to secure the unit.
ThisHampton®Mobile/ManufacturedHome
listed appliance comes equipped with a
dedicated #8 ground lug to which an 18
gauge copper wire from the steel chassis
ground must be attached.
This appliance may only be installed
in an aftermarket permanently located,
manufactured (USA only )or mobile
home, where not prohibited by local
codes.
Thisapplianceisonlyforusewiththetype
of gas indicated on the rating plate. This
appliance is not convertible for use with
othergases,unlessacertifiedkitisused.

8Hampton® H35-2 Direct Vent Freestanding Gas Stove
INSTALLATION
BEFORE YOU START
Safe installation and operation of this appliance
requirescommonsense,however,wearerequired
bytheCanadianSafetyStandardsandANSIStand-
ards to make you aware of the following:
1) Provide adequate clearances for servicing,
proper operation and around the air openings
into the combustion chamber.
2) The appliance must be installed on a flat, solid,
continuoussurface(e.g.wood,metal,concrete).
This may be the floor, or it can be raised up on
a platform to enhance its visual impact. The
appliance may be installed on carpeting, tile,
wood flooring or other combustible material,
because the appliance's base extends the full
width and depth of the appliance. The Direct
Vent Freestanding Gas Stove can be installed
in a wide variety of ways and will fit nearly any
room layout. It may be installed in a recessed
position, framed out into the room, or across a
corner.
3) The Direct Vent Freestanding Gas Stove is
approved for alcove installations, which meet
the clearances listed in the "Clearance to
Combustibles" section. This unit is approved
for manufactured home installations, see the
"ManufacturedMobileHomeAdditionalRequire-
ments" section and the "VentingArrangement"
section for the required vent arrangements. If
installed into a manufactured home the unit
must be bolted down to the floor.
4) ThisapplianceisListedforbedroom installations
when used with a Listed Millivolt Thermostat.
Some areas may have further requirements,
check local codes before installation.
5) Thisapplianceis ListedforAlcoveinstallations,
maintainminimumAlcoveclearancesasfollows,
minimum width of 40" (1016mm), a maximum
depth of 36" (914mm), and minimum ceiling
height of 64" (1626mm) from floor to ceiling.
6) Werecommendthatyouplanyourinstallationon
paperusingexactmeasurementsforclearances
andfloorprotectionbeforeactuallyinstallingthis
appliance. Have a qualified building inspector
review your plans before installation.
CLOTHING OR OTHER FLAMMABLE
MATERIAL SHOULD NOT BE PLACED
ON OR NEAR THE APPLIANCE.
CHILDREN AND ADULTS SHOULD BE
ALERTED TO THE HAZARDS OF HIGH
SURFACE TEMPERATURES, ESPE-
CIALLY THE FIREPLACE GLASS, AND
SHOULD STAY AWAYTO AVOID BURNS
OR CLOTHING IGNITION.
INSTALLATION AND REPAIR SHOULD
BE DONE BY AN AUTHORIZED
SERVICE PERSON. THE APPLIANCE
SHOULD BE INSPECTED BEFORE
USE AND AT LEAST ANNUALLY BY A
PROFESSIONAL SERVICE PERSON.
MORE FREQUENT CLEANING MAY
BE REQUIRED DUE TO EXCESSIVE
LINT FROM CARPETING, BEDDING
MATERIAL,ETC. IT IS IMPERATIVETHAT
CONTROL COMPARTMENTS, BURNERS
AND CIRCULATING AIR PASSAGEWAYS
OF THE APPLIANCE BE KEPT CLEAN.
DUE TO HIGH TEMPERATURES, THE
APPLIANCE SHOULD BE LOCATED
OUT OF TRAFFIC AND AWAY FROM
FURNITURE AND DRAPERIES.
WARNING: FAILURE TO INSTALL THIS
APPLIANCE CORRECTLY WILL VOID
YOUR WARRANTY AND MAY CAUSE A
SERIOUS HOUSE FIRE.
YOUNG CHILDREN SHOULD BE CARE-
FULLY SUPERVISED WHEN THEY ARE
IN THE SAME AREA AS THE APPLI-
ANCE. TODDLERS,YOUNG CHILDREN
AND OTHERS MAY BE SUSCEPTIBLE
TO ACCIDENTAL CONTACT BURNS. A
PHYSICAL BARRIERS IS RECOMMEND-
ED IFTHERE ARE AT RISK INDIVIDUAL
INTHE HOUSE. TO RESTRICT ACCESS
TO A FIREPLACE OR STOVE, INSTALL
AN ADJUSTABLE SAFETY GATE TO
KEEP TODDLERS, YOUNG CHILDREN
AND OTHER AT RISK INDIVIDUALS OUT
OF THE ROOM AND AWAY FROM HOT
SURFACES.

Hampton® H35-2 Direct Vent Freestanding Gas Stove 9
INSTALLATION
GENERAL SAFETY
INFORMATION
1) The appliance installation must conform with
local Canadian Electrical Code.
2) Theappliancewheninstalled,mustbeelectri-
callygroundedinaccordancewithlocalcodes,
or in the absence of local codes with the cur-
rent National Electrical Code, ANSI/NFPA 70
or CSA C22.1 Canadian Electrical Code.
3) The applianceshouldbeinspectedforshipping
damagebeforeuseandservicedannuallyby
aprofessionalserviceperson.Morefrequent
cleaning may be required due to excessive
lint from carpeting, bedding material, etc. It
is imperative that control compartments, and
circulating air passageways of the appliance
bekeptcleanandfreefromexcessivelintfrom
carpeting.
4) See general construction and assembly in-
structions. The appliance and vent should be
enclosedwhen installed inorpassing through
a living area, where children may come in
contact with it.
5) Thisappliancemustbeconnectedtothespeci-
fied vent and termination cap to the outside
of the building envelope. Never vent to
another room or inside a building. Make sure
that the vent is fitted as per the instructions
starting in the "Exterior Vent Terminal Loca-
tions" section.
6) Inspectthe venting system annuallyforblock-
age and any signs of deterioration.
7) Venting terminals shall not be recessed into a
wall or siding.
8) Any safety glass removed for servicing must
be replaced prior to operating the appliance.
9) To prevent injury, do not allow anyone who
is unfamiliar with the operation to use the
fireplace.
INSTALLATION
CHECKLIST
1) Locate your appliance. Refer to the following
sections:
a. Clearances to combustibles
b. Locating Your Gas Stove
c. For venting requirements, see "Venting
Introduction" to "Venting Arrangements"
Section.
2) InstallOptionalFan.Refertothe"OptionalFan
Installation" section.
3) Setventrestrictors.Refertothe"VentRestrictor
Position" section.
4) Install venting. Refer to the following sections
where applicable:
a. Check all venting requirements.
See "Venting Introduction" to "Venting
Arrangements" sections.
b. Vertical Termination with Co-linear Flex
System
c. DV Stove Horizontal Vent Kit
d. Dura-Vent Termination Kit.
5) Make gas connections. Refer to the "Gas
Connection" section
Test the pilot. Must be as per diagram in the
"Maintenance Instruction" section.
If converting to Propane, make changes prior
see the "Conversion from Natural Gas to
Propane" section.
6) Test Gas Pressure. Refer to the "Gas Pipe
Pressure Testing" section.
7) Install standard and optional features. Refer
to the following sections where applicable:
a. Brick Panels
b. Log Set Installation
c. Wall Thermostat
d. Remote Control
e. Optional Side Shelves
8) Finalcheck.Refertothe"FinalCheck"section.
Before leaving this unit with the customer, the
installer must ensure that the appliance is fir-
ing correctly and operation fully explained
to customer.
This includes:
1) Clocking the appliance to ensure the correct
firing rate (rate noted on label) after burning
appliance for 15 minutes.
2) If required, adjusting the primary air to ensure
that the flame does not carbon. First allow the
unit to burn for 15-20 min. to stabilize.
CAUTION: Any alteration to the product that
causes sooting or carboning that results in
damage is not the responsibility of the manu-
facturer.
CLEARANCES TO
COMBUSTIBLES
The clearances listed are MINIMUM distances.
Measure the clearance to both the appliance and
the chimney connector. The farthest distance is
correct if the two clearances do not coincide.
Forexample,ifthe appliance is set as indicated in
one of the figures but the connector is too close,
move the stove until the correct clearance to the
connector is obtained.
This appliance may be installed only with the
clearances as shown in the situations pictured.
Do not combine clearances from one type of
installation with another in order to achieve
closer clearances.
This unit can be installed on a solid combustible
surface like a wood floor. This unit can also be
installed directly on carpeting or vinyl.
Use the minimum clearances shown in the dia-
grams below:
H35-NG2 & H35-LP2 Clearances
A Side Wall to Unit 6-1/2" / 165 mm
B Back Wall to Unit 6" / 152 mm
C Vertical Vent Pipe to Back Wall
2" / 50 mm
E Unit Corner to Wall 2" /50 mm
Unit Top to Alcove Ceiling 36" / 914 mm
Minimum ceiling height is 36" /914 mm from top
of unit.
Emissions from burning wood or gas could
contain chemicals known to the State of
California to cause cancer, birth defects or
other reproductive harm.

10 Hampton® H35-2 Direct Vent Freestanding Gas Stove
INSTALLATION
OPTIONAL FAN INSTALLATION
Fan Kit Contains:
Diagram 1
Diagram 2
LOCATING YOUR
GAS STOVE
When selecting a location for your stove, ensure
that the clearances listed above are met as well
asensuringthatthereisadequateaccessibilityfor
servicing and proper operation.
MANUFACTURED
MOBILE HOME
ADDITIONAL
REQUIREMENTS
1) Ensure that structural members are not cut or
weakened during installation.
2) Ensure proper grounding using the #8 ground
lug provided.
3) Appliance must be anchored to the floor with
the supplied anchoring methods.
COMBUSTION AND
VENTILATION AIR
The combustion air from this appliance is drawn
from outside the building through the outer flue.
Extra provision for combustion air inside the
room is not required.
A) Cross Corner
B) Room Divider
C) Island
D) Flat on Wall
E) Flat on Wall Corner
F) Flush with Wall/Alcove
For Vent Termination requirements, see the "Ex-
terior Vent Terminal Locations" section.
Qty. Description
1 Fan Speed Controller with nut, and
knob.
1 Fan Assembly c/w green wire
attached
1 Power cord
1 Plastic locking grommet
1) Remove the Top Control Panel Assembly
by removing the three screws. Diagram 1.
2) Remove the nylon hole plug from the control
panel.
3) Install the fan speed controller onto the control
panel and secure with nut. Connect remaining
wire harness wires to speed control. NOTE:
Speed control wires must be in the down posi-
tion when control panel is in place.
4) Push black knob onto speed control.
5) Remove the rear access panel on the back of
the stove by removing the 6 screws. Install the
fan onto pins as per Diagram 2.
NOTE: Do NOT damage, cut or remove the 3"
aluminum air intake pipes.
Hint for pushing fan down onto pins - rub a bit
of dish soap on the pins so the grommets will
slidedownmoreeasily.Checktomakesurethe
fan is seated properly on the pins - try to move
the fan back and forth.
6) Push power cord through hole in the rear panel
14" - 16" and tie a loose knot in the cord on the
inside to prevent the power cord from being
pulled out. Diagram 2.
7) Installlockinggrommettopowercordandpush
through hole in the rear panel and give a 1/4
turn to secure.
NOTE: When running wires, keep them clear
of valve assembly and tubing to avoid
tangling of wires and valve.
NOTE: Becarefulnottocutwireswhenpassing
through holes in the firebox.
8) Run green ground wire from fan and connect
to grounding lug.
9) Connect green power cord ground wire to
grounding lug.
10) Runtheneutralblackwire frompower cordand
connect to fan motor.
11) Run the live black wire from power cord and
connect to speed control wire.
12) Connect the white wire of the wire harness to
the fan terminal.
NOTE: Pull excess wire next to fan to avoid
excessive heat from the firebox.
13) Ensureallwiresarepulled awayfrom fireboxto
avoid excessive heat and secure with stick-on
wire clip.
14) Re-attach control panel with 3 screws, revers-
ing step 1. Re-attach rear access panel with 6
screws, reversing step 5.
NOTE: When power cord is plugged in, speed
control is in the ON position and stove is burn-
ing, allow 10 - 15 minutes for the thermodisc
(temperatureswitch) to activate and turnon the
Fan automatically.
WARNING:
Electrical Grounding Instructions
This appliance is equipped with a
three pronged (grounding) plug for
yourprotectionagainstshockhazard
and should be plugged directly into
a properly grounded three-prong
receptacle. Do not cut or remove the
grounding prong from this plug.

Hampton® H35-2 Direct Vent Freestanding Gas Stove 11
INSTALLATION
INSTALLATION
PRECAUTIONS
These venting systems are engineered products
that have been designed and tested for use with
the H35-NG2, and H35-LP2. The warranty will be
voided and serious fire, health or other safety haz-
ards may result from any of the following actions:
1) Installation of any damaged Direct Vent com-
ponent
2) Unauthorized modification of the Direct Vent
System
3) Installation of any component part not
approved by FPI - Fireplace Products
International Ltd.
4) Installation other than as instructed by the
approved rigid pipe manufacturers and FPI
Fireplace Products International Ltd.
Warning: Always maintain required
clearances (air spaces) to nearby
combustiblestopreventafirehazard.
Do not fill air spaces with insulation.
Be sure to check the vent termination clearance
requirements from decks, windows, soffits, gas
regulators,airsupplyinletsandpublicwalkwaysas
specified in the "Exterior Vent Terminal Locations"
section and in your local building codes.
The gas appliance and vent system must be
vented directly to the outside of the building,
and never be attached to a chimney serving a
separate solid fuel or gas-burning appliance.
Each direct vent gas appliance must use it's own
separate vent system. Common vent systems are
prohibited.
SAFETY PRECAUTIONS
FOR THE INSTALLER
1) Weargloves and safety glasses forprotection.
2) Exercise extreme caution when using ladders
or on roof tops.
3) Be aware of electrical wiring locations in walls
and ceilings.
VENTING
INTRODUCTION
The Horizontal Termination Kit and the rigid pipe
ventingsystems,incombinationwiththe DirectVent
FreestandingGasStoves,H35-NG2andH35-LP2,
have been tested and listed as direct vent heater
systems by Warnock Hersey.
These units use the "balanced flue" technology
Co-Axial system. The inner liner vents products
of combustion to the outside while the outer pipe
draws outside combustion air into the combustion
chambertherebyeliminatingtheneedtouseheated
room air for combustion and losing warm room air
up the chimney.
Note: These flue pipes must not be
connected to any other appliance.
Thegasapplianceandventsystemmustbevented
directly to the outside of the building, and never
be attached to a chimney serving a separate solid
fuelorgas burningappliance. Eachdirect ventgas
appliancemust use it's own separate vent system.
Common vent systems are prohibited.
IMPORTANT
Read all instructions carefully before starting the
installation.Failuretofollowtheseinstructionsmay
createafireorothersafetyhazard,andwillvoidthe
warranty. Be sure to check the venting and clear-
ance to combustible requirements. Consult your
local building codes before beginning installation.
The location of the termination cap must conform
to the requirements in the "Exterior Vent Terminal
Locations" section.
VENT RESTRICTOR
POSITION
Ventrestrictionisrequiredforcertainventinginstal-
lations,seethediagramsin"VentingArrangement"
section to determine if they are required for your
installation.
To set the Vent restriction as indicated in the dia-
gramsinthe"VentingArrangement"section, simply
loosenthescrewsandpushtheventrestrictorplate
to the correct position. Tighten the screws.
Horizontal Termination:
Vent Restrictor setting at 36,000 Btu/h
Vertical Termination:
Vent Restrictor setting at 36,000 Btu/h

12 Hampton® H35-2 Direct Vent Freestanding Gas Stove
INSTALLATION
EXTERIOR VENT TERMINAL LOCATIONS
Minimum Clearance Requirements Canada1USA2
AClearance above grade, veranda, porch, deck, or balcony 12"(30cm) 12"(30cm)
BClearance to window or door that may be opened 12"(30cm) 9" (23cm)
CClearance to permanently closed window **
DVertical clearance to ventilated soffit located above the terminal within a horizontal distance of 2 feet (61cm)
from the center line of the terminal (check with the local code)
22"(56cm) 22"(56cm)
EClearance to unventilated soffit 12"(30cm) 12"(30cm)
FClearance to outside corner: with AstroCap and Vent Riser Termination Caps 6"(15cm) 6"(15cm)
Clearance to outside corner: with all other approved Termination Caps 12"(30cm) 12"(30cm)
GClearance to inside corner: with AstroCap and Vent Riser Termination Caps 6"(15cm) 6"(15cm)
Clearance to inside corner: with all other approved Termination Caps 12"(30cm) 12"(30cm)
HClearance to each side of center line extended above meter/regulator assembly 36"(90cm)a*
JClearance to service regulator vent outlet 36"(90cm) *
KClearance to non-mechanical air supply inlet to building or the combustion air inlet to any other appliance 12"(30cm) 9" (23cm)
LClearance to a mechanical air supply inlet
#3' (91cm) above if within 10' (3m) horizontally.
72"(1.8m) 36"(90cm)b
MClearance above paved sidewalk or a paved driveway located on public property 84"(2.1m)┼*
NClearance under veranda, porch, deck, or balcony 12"(30cm)‡*
1In accordance with current CSA B149.1, Natural Gas and Propane Installation Code
2In accordance with the current ANSI Z223.1/NFPA 54, National Fuel Gas Code
┼A vent shall not terminate directly above a sidewalk or paved driveway which is located between two single family dwellings and serves both dwellings.
‡ Permitted only if veranda, porch, deck, or balcony is fully open on a minimum of two sides beneath the floor
*Clearance in accordance with local installation codes and the requirements of the gas supplier
a3 feet (91cm) within a height of 15 feet (4.5m) above the meter / regulator assembly
b3 feet (91cm) above - if within 10 feet (3m) horizontally

Hampton® H35-2 Direct Vent Freestanding Gas Stove 13
INSTALLATION
4” X 6-5/8” RIGID PIPE
CROSS REFERENCE CHART ONLY
Components from different Manufacturers may not be mixed. Not All Rigid Pipe components are available directly from FPI.
Description Simpson
Direct Vent Pro®
Selkirk
Direct Temp™
American Metal
Products®
Amerivent Direct
Metal-Fab™
Sure Seal
Security
Secure- Vent®
ICC Excel
Direct
6” Pipe Length-Galvanized 46DVA-06 4DT-6 N/A 4D6 SV4L6 TC-4DL6
6” Pipe Length-Black 46DVA-06B 4DT-6B N/A 4D6B SV4LB6 TC-4DL6B
7” Pipe Length-Galvanized N/A N/A 4D7 N/A N/A N/A
7” Pipe Length-Black N/A N/A 4D7B N/A N/A N/A
9” Pipe Length-Galvanized 46DVA-09 4DT-9 N/A N/A N/A N/A
9” Pipe Length-Black 46DVA-09B 4DT-9B N/A N/A N/A N/A
12” Pipe Length-Galvanized 46DVA-12 4DT-12 4D12 4D12 SV4L12 TC-4DL1
12” Pipe Length-Black 46DVA-12B 4DT-12B 4D12B 4D12B SV4LB12 TC-4DL1B
18” Pipe Length-Galvanized 46DVA-18 4DT-18 4D18 4D18 SV4LA TC-4DL18
18” Pipe Length-Black 46DVA-18B 4DT-18B 4D18B 4D18B SV4LA TC-4DL18B
24” Pipe Length-Galvanized 46DVA-24 4DT-24 4D24 4D24 SV4L24 TC-4DL2
24” Pipe Length-Black 46DVA-24B 4DT-24B 4D24B 4D24B SV4LB24 TC-4DL2B
36” Pipe Length-Galvanized 46DVA-36 4DT-36 4D36 4D36 SV4L36 TC-4DL3
36” Pipe Length-Black 46DVA-36B 4DT-36B 4D36B 4D36B SV4LB36 TC-4DL3B
48” Pipe Length-Galvanized 46DVA-48 4DT-48 4D48 4D48 SV4L48 TC-4DL4
48” Pipe Length-Black 46DVA-48B 4DT-48B 4D48B 4D48B SV4LB48 TC-4DL4B
60” Pipe Length-Galvanized 46DVA-60 4DT-60 N/A N/A N/A N/A
60” Pipe Length-Black 46DVA-60B 4DT-60B N/A N/A N/A N/A
Adjustable Length 3”-10”-Galvanized N/A N/A N/A 4DAL N/A TC-4DLT
Adjustable Length 3”-10”-Black N/A N/A N/A 4DALB N/A TC-4DLTB
Adjustable Length 7”-Galvanized N/A N/A 4D7A N/A N/A N/A
Adjustable Length 7”-Black N/A N/A 4D7AB N/A N/A N/A
Extension Pipe 8-1/2”-Galvanized 46DVA-08A N/A N/A N/A N/A N/A
Extension Pipe 8-1/2”-Black 46DVA-08AB N/A N/A N/A N/A N/A
Adjustable Length 12”-Galvanized N/A N/A 4D12A N/A SV4LA12 N/A
Adjustable Length 12”-Black N/A N/A 4D12A N/A SV4LBA12 N/A
Extension Pipe 16”-Galvanized 46DVA-16A N/A N/A N/A N/A N/A
Extension Pipe 16”-Black 46DVA-16AB N/A N/A N/A N/A N/A
45ºElbow-Galvanized 46DVA-E45 4DT-EL45 4D45L N/A N/A TE-4DE45
45ºElbow-Black 46DVA-E45B 4DT-EL45B 4DT-EL45B N/A N/A TE-4DE45B
45ºElbow Swivel-Galvanized See 46DVA-E45 N/A N/A 4D45L SV4E45 N/A
45ºElbow Swivel-Black See 46DVA-E45B N/A N/A 4D45LB SV4EB45 N/A
90ºElbow-Galvanized 46DVA-E90 4DT-EL90S 4DT-EL90S N/A N/A TE-4DE90
90ºElbow-Black 46DVA-E90B 4DT-EL90SB 4DT-EL90SB N/A SV4EBR90-1 TE-4DE90B
90ºElbow, Swivel-Galvanized See 46DVA-E90 N/A N/A 4D90L SV4E90-1 N/A
90ºElbow, Swivel-Black See 46DVA-E90B N/A N/A 4D90LB SV4EB90-1 N/A
90º Starter Elbow, Swivel-Galvanized N/A N/A N/A 4D90A N/A N/A
Adaptor* N/A N/A N/A 4D90L N/A N/A
Ceiling Support N/A 4DT-CS 4DFSP 4DSP SV4SD TE-4DE45
Cathedral Support Box 46DVA-CS 4DT-CSS 4DRSB 4DRS SV4CSB TE-4DE45B
Wall Support/Band 46DVA-WS 4DT-WS/B 4DWS 4DWS SV4BM N/A
Offset Support 46DVA-ES (N/A - FPI) 4DT-OS N/A N/A SV4SU N/A
Wall Thimble-Black 46DVA-WT 4DT-WT 4DWT 4DWT SV4RSM TE-4DE90
Wall Thimble Support/Ceiling Support 46DVA-DC N/A N/A N/A SV4PF TE-4DE90B
Firestop Spacer 46DVA-FS 4DT-FS 4DFSP 4DFS SV4BF N/A
Trim Plate-Black N/A 4DT-TP 4DFPB 4DCP SV4LA N/A

14 Hampton® H35-2 Direct Vent Freestanding Gas Stove
INSTALLATION
Description Simpson
Direct Vent Pro®
Selkirk
Direct Temp™
American Metal
Products®
Amerivent Direct
Metal-Fab™
Sure Seal
Security
Secure- Vent®
ICC Excel
Direct
Attic Insulation Shield 12” 46DVA-IS N/A@ FPI N/A 4DAIS12 N/A SV4RSA N/A
Attic Insulation Shield - Cold Climates 36” N/A N/A 4DAIS12 N/A N/A TM-4AS
High Wind Vertical Cap 46DVA-VCH N/A N/A N/A N/A TM-4VT
High Wind Horizontal Cap 46DVA-HC N/A N/A N/A N/A TM-4DHT
Horizontal Square Termination Cap See 46DVA-HC 4DT-HHC 4DHC 4DHT SV4CHC-1 TM-4HT
Vertical Termination Cap 46DVA-VC 4DT-HVC 4DVC 4DVT SV4CGV-1 TM-4VT
Storm Collar 46DVA-08A 4DT-SC 4DSC 4DSC SV4FC TM-SC
Restrictor Disk 46DVA-RD N/A N/A N/A N/A TM-4DS
Extended Vertical Termination Cap 46DVA-VCE N/A N/A N/A N/A N/A
Chimney Conversion Kit A (USA only) 46DVA-KCA N/A N/A N/A N/A TM-4CA6
Chimney Conversion Kit B (USA only) 46DVA-KCB N/A N/A N/A N/A TM-4CA7
Chimney Conversion Kit C (USA only) 46DVA-KCC N/A N/A N/A N/A TM-4CA8
Chimney Conversion Kit Masonry
(USA only)
46DVA-KMC N/A N/A N/A N/A N/A
Wall Firestop 46DVA-WFS N/A N/A N/A N/A TM-4TR
Colinear Flex Connectors 46DVA-ADF N/A N/A N/A N/A N/A
Adjustable Flashing 0/12-6/12 N/A 4DT-ST14 4D12S 4DST14 SV4STC14 TF-4FA
Adjustable Flashing 6/12-12/12 N/A 4DT-ST36 4D36S 4DST36 SV4STC36 TF-4FB
Vinyl Siding Standoff 46DVA-VSS 4DT-VS N/A 4DVS SV4VS TM-VSS
Vinyl Siding Shield Plate N/A 4DT-VSP N/A N/A SV4VS N/A
Snorkel Termination 14” 46DVA-VCH N/A N/A N/A N/A TM-4ST14
Snorkel Termination 36” 46DVA-HC N/A N/A N/A N/A TM-4ST36
Basic Horizontal Termination Kit (A) Disc. 4DT-HKA 4DHTK2 4DHTKA SV-SHK N/A
Horizontal Termination Kit (B) 46DVA-KHA
(Changed Components)
4DT-HKB 4DHTK1 4DHTKB SV-HK N/A
Vertical Termination Kit Disc. 4DT-VKC 4DHTK 4DHTK SV-FK N/A
FPI
946-506/P Vent Guard (Optional) for AstroCap 946-205 Vinyl Siding Shield for Riser Vent Terminal
510-994 Rigid Pipe Adaptor (Must use with all rigid piping) 946-208/P Vent Guard (Optional) for Riser Vent Terminal
640-530/P Riser Vent Terminal 946-523/P AstroCap Horizontal Cap
946-206 Vinyl Siding Standoff for AstroCap
Note: When using Metal-Fab Sure Seal Rigid Piping - please note that the Adaptor (4DDA) must be used in conjunction with FPI Rigid Pipe Adaptor (510-994).
Note: Horizontal runs of vent must be level, or have a 1/4” rise for every 1 foot of run towards the termination.
Never allow the vent to run downward - this could cause high temperatures and may present a possible fire hazard.
Offset Pipe Selection: Use this table to determine offset pipe lengths.
Pipe Length
(L)
4” x 6-5/8” Venting For specific instructions on venting components - visit the
manufacturers website listed below.
Run (X) Rise (Y)
0” (0mm) 4-7/8” (124mm) 13-7/8” (340mm) Simpson Direct Vent Pro: www.duravent.com
6” (152mm) 8” (203mm) 16-1/2” (419mm) Selkirk Direct-Temp: www.selkirkcorp.com
9” (229mm) 10-1/8” (257mm) 18-5/8” (473mm) American Metal Products: www.americanmetalproducts.com
12” (305mm) 12-1/4” (311mm) 20-3/4” (527mm) Metal-Fab Sure Seal: www.mtlfab.com
24” (610mm) 20-5/8” (524mm) 29-1/8” (740mm) Security Secure Vent: www.securitychimneys.com
36” (914mm) 29” (737mm) 37-1/2” (953mm) Industrial Chimney Company: www.icc-rsf.com
48” (1219mm) 37-7/16” (951mm) 45-15/16” (1167mm)

Hampton® H35-2 Direct Vent Freestanding Gas Stove 15
INSTALLATION
RIGID PIPE VENTING SYSTEMS
Horizontal or Vertical Terminations
Alternate
Horizontal
Termination
Caps
The FPI AstroCapTM and FPI Riser Vent terminal are certified for installations using FPI venting systems as well as Simpson Dura-Vent®Direct Vent Pro,
American Metal Products Ameri Vent Direct Vent, Security Secure Vent®, Selkirk Direct-Temp. AstroCapTM is a proprietary trademark of FPI Fireplace
Products International Ltd. Dura-Vent® and Direct Vent Pro are registered and/or proprietary trademarks of Simpson Dura-Vent Co. Inc.
This product has been evaluated by Intertek
for use with Duravent Direct-Vent Pro, Selkirk
Direct-Temp, Ameri Vent Direct venting and
Security Secure Vent systems.
WARNING:
Do not combine venting components from
different venting systems.
However use of the the AstroCapTM and FPI
Riser is acceptable with all systems.
When using Rigid Vent other than
Simpson Dura-Vent, 3 screws must be
used to secure rigid pipe to adaptor.

16 Hampton® H35-2 Direct Vent Freestanding Gas Stove
INSTALLATION
Offset to Vertical Terminations
VENTING ARRANGEMENTS
Vertical Terminations Systems for
Residential Manufactured and Mobile Homes
The shaded area in the diagram below shows all allowable combinations of straight vertical and
offset to vertical runs with vertical terminations. Maximum two 45oelbows.
If the vent is ENCLOSED in a chase (min. size 9" x 9") maintain a 1-1/4" clearance to combustibles.
May be installed in Manufactured (Mobile) Homes after first sale.
Horizontal Terminations for All
Venting Systems
The shaded areas in the diagram below show
allallowablecombinationsofverticalrunswith
horizontal terminations. Maximum one 90O
elbow (two 45o elbows equal one 90oelbow).
All approved caps listed on page 12 - may
be used.
Propane and Natural Gas:
Residential, Manufactured and
Mobile Homes Installations
The venting arrangements diagrammed below,
haveamin. of 75% (flue loss) efficiency withFan
Off,asrequiredformanufacturedhomes.(Actual
efficiency may be as high as 85%)
May be installed in Manufactured (Mobile)
Homes after first sale.
ROTATING 45OELBOW FOR STRAIGHT HORIZONTAL TERMINATIONS
1)Removeall4screwsthatsecure
the elbow to the unit using a 1/4"
magnetic nut driver.
2) Rotate the elbow 180o
3) Secure the elbow by securing
it with the 4 screws.
Remove all 4 screws
and washers
NOTE: See "Vent Restrictor Position" section for
installation instructions for the Vent Restrictor
Position.

Hampton® H35-2 Direct Vent Freestanding Gas Stove 17
INSTALLATION
VENTING ARRANGEMENTS
HORIZONTAL TERMINATIONS USING RIGID PIPE
Snorkel Termination Riser Vent Termination
The two diagrams show all allowable com-
binationsof straighthorizontal termination
using Rigid Pipe. Restrictor position "A".
Only a snorkel or FPI Riser vent may be
used as shown. No other termination cap
is permitted.
Venting Arrangements -Straight Horizontal Termination at a De-Rated BTU
The diagrams show all allowable combina-
tionsofstraighthorizontalterminationusing
Rigid Pipe. Restrictor position "A". Refer to
the "Conversion Kit to Lower BTU Rating"
section for de-rating instructions.
Note: If venting this appliance as per the
diagrams shown in the two diagrams, the unit
"must" be derated using part #740-950 for NG
and part #740-952 for LP. Refer to the conver-
sion kit to lower BTU rating section for derating
instructions.
Also, only a snorkel or FPI Riser vent may be
usedasshowninthenoteddiagrams. Noother
termination cap is permitted.
Dangerous operating conditions will occur
if these instructions are not adhered to.
*Ifthis isan outsidecorner,theminimum dis-
tancebetweentheventandtheoutsidecorner
is 6” (15cm). See “F” on the diagram in the
"Exterior Vent Terminal Locations" section.
Snorkel Termination Riser Vent Termination

18 Hampton® H35-2 Direct Vent Freestanding Gas Stove
INSTALLATION
Horizontal Venting with Two (2) 90oElbows
Option V H + H1
A) 3' Min. 2' Max.
B) 4' Min. 3' Max.
C) 5' Min. 4' Max.
D) 6' Min. 5' Max.
E) 7' Min. 6' Max.
F) 8' Min. 8' Max.
Horizontal Venting with Two (2) 90oElbows
Option H V H + H1
A) 1' Max. 2' Min. 3' Max.
B) 2' Max. 3' Min. 5' Max.
C) 3' Max. 5' Min. 6' Max.
D) 4' Max. 7' Min. 7' Max.
E) 5' Max. 9' Min. 8' Max.
With these options, max.
total pipe length is 30 feet
with min. of 9 feet total
vertical and max. 8 feet
total horizontal.
Please note min. 1 foot
between 90oelbows is
required.
With these options, maxi-
mum total pipe length is 30
feet with minimum of 8 feet
totalvertical and maximum
8 feet total horizontal.
Please note minimum 1
foot between 90oelbows
is required.
One 90oelbow = Two 45oelbows.
One 90oelbow = Two 45oelbows.
Vent restrictor position A (fully open), refer to the
"Vent Restrictor Position" section.
Vent restrictor position A (fully open), refer to the "Vent
Restrictor Position" section.
H1
H
V
Lengths do not include elbow indicated
Lengths do not include elbow indicated

Hampton® H35-2 Direct Vent Freestanding Gas Stove 19
INSTALLATION
H1
H
V
Vertical Venting with Two (2) 90oElbows
Option V H V + V1
A) 1' Min. 3' Max. 2' Min.
B) 2' Min. 4' Max. 3' Min.
C) 3' Min. 5' Max. 4' Min.
D) 4' Min. 6' Max. 5' Min.
E) 5' Min. 7' Max. 6' Min.
Vertical Venting with Two (2) 90oElbows
Withthese options,max. total
pipelengthis30feetwithmin.
of6feettotalverticalandmax.
7 feet total horizontal.
Please note min. 1 foot
between 90oelbows is
required.
Option H + H1 V
A) 2' Max. 2' Min.
B) 3' Max. 3' Min.
C) 4' Max. 4' Min.
D) 5' Max. 5' Min.
E) 6' Max. 6' Min.
Withtheseoptions,max.total
pipelengthis30feetwithmin.
of6feettotalverticalandmax.
6 feet total horizontal.
Please note min. 1 foot
between 90oelbows is
required.
One 90oelbow = Two 45oelbows.
One 90oelbow = Two 45oelbows.
Vent restrictor position A (fully open), refer to the "Vent Re-
strictor Position" section.
Vent restrictor position A (fully open), refer to the
"Vent Restrictor Position" section.
Lengths do not include elbow indicated
Lengths do not include elbow indicated

20 Hampton® H35-2 Direct Vent Freestanding Gas Stove
INSTALLATION
Venting Arrangements - Vertical Terminations
with Co-linear Flex System for both
Residential & Manufactured Homes
into Masonry Fireplaces
The shaded area in the diagram shows the allowable vertical
terminations. Note: Must remove 4 screws from stove collar
androtate 180oto have collar facingstraight back.Secure into
place with 4 screws.
VERTICAL TERMINATION WITH CO-LINEAR FLEX SYSTEM
THE APPLIANCE MUST NOT BE
CONNECTED TO A CHIMNEY FLUE
SERVING A SEPARATE SOLID FUEL
BURNING APPLIANCE.
This appliance is designed to be attached to
two 3" (76mm) co-linear aluminium flex running
the full length of the chimney. See the Venting
Arrangements chart below for minimum and
maximum flue lengths. See chart below for
minimumdistancesfromroof.Periodicallycheck
that the vent is unrestricted.
Masonrychimneysmaytake variouscontours whichthe flexiblelinerwillaccommodate.However,
keep the flexible liner as straight as possible, avoid unnecessary bending.
The Air Intake pipe must be attached to the inlet air collar of the termination cap.
Straight Vertical Terminations
Required Parts:
Part # Description
946-529 Co-linear DV Vertical
Termination Cap
948-305 3" Flex - 35 ft.
946-563 Co-Axial to Co-Linear Adaptor Kit
which contains the following:
Co-linear Flex Adaptor (270-585)
Outer Pipe (946-257)
Inner Pipe Adaptor (946-219)
Vent Restrictor
setat1-3/4"open
(fully open),
Position "A"