HAMPTON BAY NXT-LV-PW06 User manual

Use and Care Guide
LED Path Light
-LV-PW06
1001486801
IN OUT
E
ACD
B
A - Light x 6 B - Stake x 6 C - Transformer x 1 D - 45’ wire x 1 E - Photocell x 1
IN OUT
D
Assembly and Installtion
Attaching and installing the light
Push the stake (C) assembly into the
ground.
Do not push on the light.
1Connecting the wires 2
IMPORTANT: Do not instanll
install the light within 10 ft. (3m) of
a pool, spa, or fountain.
Detach and place the wire connector (D) on opposite sides of the
low voltage cable (not included) from the transformer (not included)
where the xture will be located.
Align and t the main low voltage cable vertically to the slot of the
wire connector (D).
Press the wire connector (D) together untilit is locked around the
main low voltage cable.Pre-set prongs will pierce the cable
insulation and establish contact with the electrical wire inside.
Once the wire connector (D) is in place, wrap it with electrical tape
(not included) for additional protection.
When the lights are installed, turn on the power.
WARNING: The connector contacts (D) have sharp edges for
piercing the main low voltage cable. To avoid injury, do not
touch the metal contacts.
CAUTION: The wire from the low voltage power unit shall be
12-16 AWG type underground low Energy Circult Cable.
IMPORTANT:
Protect the wiring by routing it in close proximity to the light,
tting, or next to a building structure such as a house or a
deck.
Do not bury the wiring by more than 6 in. (15.24 cm) in order
to connect to the main secodary wire.
Do not submerge xtures in water.
·
·
·
HAMPTONBAY.COM
Please contact 1-855-HD-HAMPTON for further assistance.
1
NOTE: Do not use a hammer.If
the ground is hard, use water to
soften or a trowel to loosen the
soil.
A
B
C
D

Care & Cleaning
Before attempting to clean the xture, disconnect the power to the xture by turning the breaker off or removing
the fuse from the fuse box.
To clean the xture, use a dry or slightly dampened clean cloth.
Do not use chemicals, solvents, or harsh abrasives, as damage to the xture may occur.
Troubleshooting
Problem Possible Cause Solution
The light do not turn on.
Cable Selection
Warranty
The manufacturer warrants this product to be free for one (1) year against any defects that are due to faulty materials
or workmanship. This warranty applies only to the original consumer purchaser and only to products used in normal
use and service. If this product is found to be defective, the manufacturer’s only obligation, and your exclusive
remedy, is the repair or replacement of the product at the manufacturer’s discretion, provided that the product has
not been damaged through misuse, abuse, accident, modications, alterations, neglect, or mishandling. This
warranty shall not apply to any product that is found to have been improperly installed, set up, or used in any way not
in accordance with the instructions supplied with the product. This warranty shall not apply to a failure of the product
as a result of an accident, misuse, abuse, negligence, alteration, or faulty installation or any other failure not relating
to faulty workmanship. This warranty shall not apply to the nish on any portion of the product, such as surface
and/or weathering, as this is considered normal wear and tear. The manufacturer does not warrant and specically
disclaims any warranty, whether expressed or implied, or tness for a particular purpose, other than the warranty
contained herein. The manufacturer specically disclaims any liability and shall not be liable for any consequential or
incidental loss or damage, including any labor/expense costs involved in the replacement or repair of said product.
Contact the Customer Service Team at 1-855-HD-HAMPTON or visit www.Hamptonbay.com.
A light ickers.
The lights on all xtures
icker.
Check the outlet and ensure that a breaker or GFCI circult
has not been tripped.
Follow the wires from the xture and ensure a continuous
connected path back to the transformer.
Check the setting on the transformer.
Tighten the wire connector and ensure the metal contacts
pierce the insulation on the low voltage cable from the
transformer.
Unplug the transformer from the outlet and visually inspect
the positive and negative connecting posts. Each wire should
be securely screwed in and not in contact with another.
There is no power.
There is a disconnection or
break in the wire.
The transfomer setting is
incorrect.
There is a loose wire
connector to the xture.
There is a loose connection
at the transformer.
* NOT RECOMMENDED FOR HALOGEN LANDSCAPE LIGHTS
This data is provided as a general guideline. Actual performance will depend on the installation layout, the xtures,
and the condition of the cable.
2
12 VOLT TAP
Cable Length
Total Fixture Wattage
0-50 feet
51-100 feet
101-150 feet
16 AWG
16 AWG
14 AWG
16 AWG
14 AWG
12 AWG
14 AWG
12 AWG
Not recommended
14 AWG
12 AWG
Not recommended
12 AWG
Not recommended
Not recommended
0
-
60 Watts
61
-
120 Watts
121
-180 Watts
181
-240 Watts
241
-300 Watts
Watts
Watts
12 AWG
Not recommended
Not recommended
12 AWG
Not recommended
Not recommended
15 VOLT TAP
Total Fixture Wattage
0
-
60 Watts
61
-
120 Watts
121
-180 Watts
181
-240 Watts
241
-300 Watts
600W Transformer = (2x300) Watts
900W Transformer = (3x300) Watts
Cable Length
0-50 feet
51-100 feet
101-150 feet
16 AWG*
16 AWG*
14 AWG*
14 AWG*
12 AWG*
12 AWG*
12 AWG*
16 AWG
16 AWG
16 AWG
12 AWG
14 AWG
12 AWG
14 AWG
12 AWG
12 AWG
Not recommended
12 AWG
Not recommended
12 AWG
Not recommended