HAMPTON BAY SKU 528-002 User manual

Page 1
INSTRUCTION MANUAL
2 Light Pendant
Lara
Home Depot SKU 528-002 (UPC 718212271322)
(Bronze fixture)
LA-2017E/S/F

Page 2
Thank you for purchasing this Hampton Bay interior light fixture. This
product has been manufactured with the highest standards of safety and
quality.
FEATURES:
1. Traditional 2 Light Pendant in Bronze Finish.
2. Timeless Elegant Design.
3. Easy to assemble and install.
QUESTIONS, PROBLEMS, MISSING PARTS:
Before returning to your local Home Depot, please call our Customer
Service Team at 1-877-527-0313 or visit www.homedepot.com. Please
reference your SKU (528-002 Bronze fixture) or UPC (718212271322
Bronze fixture).

Page 3
CAUTION:
1. Before starting installation of this fixture or removal of a previous
fixture, disconnect the power by turning off the circuit breaker or by
removing the fuse at the fuse box.
2. CONSULT A QUALIFIED ELECTRICIAN IF YOU HAVE ANY
ELECTRICAL QUESTIONS.
3. If you have any non-electrical questions about this fixture, please
contact our Customer Service Team at 1-877-527-0313 or visit
www.homedepot.com. Please reference your SKU (528-002 Bronze
fixture) or UPC (718212271322 Bronze fixture).
4. Keep your receipt and these Instructions for Proof of Purchase.
TOOLS REQUIRED FOR ASSEMBLY & INSTALLATION
(not included):
Light Bulb
(60 watt Candelabra base) Safety goggles Step Ladder Wire strippers
Flathead screwdriver Phillips screwdriver
Electrical tape Wire cutters

Page 4
PARTS INCLUDED FORASSEMBLY (parts are not to scale):
ASSEMBLY INSTRUCTIONS:
1. Shut off power at the fuse box or circuit breaker box, if necessary remove old fixture
and all mounting hardware from outlet box.
2. Carefully unpack your new fixture and lay out all the parts on a clear area, Take care
not to lose any small parts necessary for installation.
3. Place the Glass panel B (#8) into the Metal Frame B (#7) and secure with clips
located on inside of metal frame B (#7).
4. Place the Glass panel A (#6) into the Metal Frame A (#4) and secure with clips
located on inside of metal frame A (#4).
5. Place the Glass shade (#9) onto the socket and secure with the Screw shell (#10) by
using Spanner (#11) provide.
6. Align the Metal Frame B (#7) to the fold metal sheet located on the Metal Frame A
(#4) and secure with the Screw (#5).
7. Thread the Rod (#3) to Metal Frame A (#4) and thread the rest Rod (#3) one by one
to desired length, then thread the Rod (#3) to the Canopy (#2). Pull the wire until taut.
2 Screw shell(#10) 4 Rod (#3) 1 Canopy (#2)
2 Glass Shade(#9) 4 Glass panel A (#6) 4 Glass panel B (#8) 4 Screw(#5)

Page 5
ASSEMBLY:
1. Mounting Screw
2. Canopy
3. Rod
4. Metal Frame A
5. Screw
11. Spanner
10.Screw Shell
9. Glass shade
6. Glass Panel A
8.Glass Panel B
7. Metal Frame B

Page 6
PARTS INCLUDED FOR INSTALLATION (parts are not to scale):
3 Mounting Screw (#1) 1 Ground Screw (#12) 2 Outlet Box Screw (#16)
3 Wire Connector (#14) 1 Mounting Plate (#13) 1 Spanner (#11)
INSTALLATION INSTRUCTIONS:
1. Attach the Mounting Plate (#13) to the outlet box in the ceiling with two outlet box
Screws (#16). The side of the Mounting Plate marked “GND” must face out.
2. Connect the white wire from the fixture to the white wire from the Outlet Box (#15),
and the black wire from the fixture to the black wire from the Outlet Box (#15).
Cover the two wire connections using the two provided Wire Connectors (#14).
Wrap the two wire connections with electrical tape for a more secure connection. If
your outlet box has a ground wire (green or bare copper), connect fixture’s ground
wire to it using the wire connector (#14). Otherwise connect the copper ground from
the fixture to Ground screw (#12) on the Mounting Plate (#13). Note: If you have
electrical questions, consult your local electrical code for approved grounding
methods.
3. After wires are connected, tuck them carefully into the ceiling Outlet box, then place
Canopy (#2) over the Mounting Plate (#13) and secure it against ceiling with
Mounting Screw (#1).
4. Install the light bulb (not included) in accordance with the fixture’s specifications.
(DO NOT EXCEED THE MAXIMUM WATTAGE RATING!!)
5. Installation is complete. Turn on the power at the circuit breaker or fuse box. Turn
the light switch on to activate the fixture.

Page 7
INSTALLATION:
2. Canopy
13.Mounting Plate
15. Outlet Box
14. Wire Connector
12.Ground Screw
16. Outlet Box Screws
1.Mounting Screw
Ground Wire
Black Wire
White Wire

Page 8
TROUBLESHOOTING:
PRODUCT MAINTENANCE:
1. To clean the outside of the fixture, use a dry or slightly dampened clean cloth (use
clean water, never a solvent) to wipe the glass and surface of the fixture.
2. To clean the inside of the fixture, first disconnect power to the fixture by turning off
the circuit breaker or by removing the fuse at the fuse box. Next, use a dry or slightly
dampened clean cloth (use clean water, never a solvent) to wipe the inside glass and
interior surface of the fixture.
3. Do not use any cleaners with chemicals, solvents or harsh abrasives. Use only a dry
soft cloth to dust or wipe carefully.
LIMITED WARRANTY
The manufacturer warrants this lighting fixture to be free from defects in materials and workmanship for a
period of five (5) years from date of purchase. This warranty applies only to the original consumer
purchaser and only to products used in normal use and service. If this product is found to be defective, the
manufacturer’s only obligation, and your exclusive remedy, is the repair or replacement of the product at the
manufacturer’s discretion, provided that the product has not been damaged through misuse, abuse, accident,
modifications, alterations, neglect or mishandling. This warranty shall not apply to any product that is found
to have been improperly installed, set-up, or used in any way not in accordance with the instructions
supplied with the product. This warranty shall not apply to a failure of the product as a result of an accident,
misuse, abuse, negligence, alteration, or faulty installation, or any other failure not relating to faulty material
or workmanship. This warranty shall not apply to the finish on any portion of the product, such as surface
and/or weathering, as this is considered normal wear and tear.
The manufacturer does not warrant and specially disclaims any warranty, whether express or implied,
of fitness for a particular purpose, other than the warranty contained herein. The manufacturer
specifically disclaims any liability and shall not be liable for any consequential or incidental loss or
damage, including but not limited to any labor / expense costs involved in the replacement or repair of
said product.
Possible Cause Corrective Action
1. Bulb is burned out. 1. Replace light bulb.
2. Power is off. 2. Make sure power
supply is on.
3. Faulty wire connection. 3. Check wiring.
Bulb will not light.
4. Faulty switch. 4. Test or replace switch.
Fuse blows or circuit
breaker trips when light
is turned on.
Crossed wires or power wire
is grounding out. Check wire connections.