Hanasis MICUS 7 Installation instructions

-1-
www.hanasis.com
Disassembly and Assembly
System Dismantle
▶Warning!
- Make sure the system & peripherals power are off.
- Disconnect cables for peripherals & DC power input jack from the system.
!

-2-
www.hanasis.com
Disassembly and Assembly
Hard Disk Drive Replacement
1. Lay the system while preventing LCD panel is being damaged.
Raise the stand at a right angle as shown.
3. Pull in the direction of the arrow to remove the HDD.
※ Please be careful not to damage the cable.
4. Remove the screws(3ea).
HDD MEMORY BOARD T/P,LCD MSR
5. Assemble it in the opposite way of dismantling and connect
peripheral cables & DC power input jack.
2. Remove the Stand after undoing screws (4ea) which hold the
stand.

-3-
www.hanasis.com
4. Remove the HDD-Support after undoing screws (3ea) which
hold the HDD-Support.
Disassembly and Assembly HDD MEMORY BOARD T/P,LCD MSR
Memory Module Replacement
1. Lay the system while preventing LCD panel is being damaged.
Raise the stand at a right angle as shown.
3. Pull in the direction of the arrow to remove the HDD.
※ Please be careful not to damage the cable.
HDD-Support
2. Remove the Stand after undoing screws (4ea) which hold the
stand.

-4-
www.hanasis.com
6. Install new memory as shown in the figure and tighten them
with levers at both ends.
Disassembly and Assembly HDD MEMORY BOARD T/P,LCD MSR
Memory Module Replacement
Memory

-5-
www.hanasis.com
Main-board and Sub-board Removal
3. Remove the screws(3ea). 4. With reference to the order of the pictures to remove the back
cover.
Disassembly and Assembly HDD MEMORY BOARD T/P,LCD MSR
1. Lay the system while preventing LCD panel is being damaged.
Raise the stand at a right angle as shown.
2. Remove the Stand after undoing screws (4ea) which hold the
stand.

-6-
www.hanasis.com
7. Remove the HDD-Support after undoing screws (3ea) which
hold the HDD-Support.
■Parts List ■
No. Part Name
1 Main-board
2 Inverter Module
3MSR-board
4 Power-board
5 Touch-board(4w)
6 Touch-board(5w)
5. Disconnect MSR cable.
Disassembly and Assembly HDD MEMORY BOARD T/P,LCD MSR
6. Remove the HDD after undoing screws (3ea) which hold the HDD.
8. Refer to the table to remove the board.
Main-board and Sub-board Removal

-7-
www.hanasis.com
Disassembly and Assembly HDD MEMORY BOARD T/P,LCD MSR
Touch-panel and TFT-LCD Removal
3. Remove the screws(3ea). 4. With reference to the order of the pictures to remove the back
cover.
1. Lay the system while preventing LCD panel is being damaged.
Raise the stand at a right angle as shown.
2. Remove the Stand after undoing screws (4ea) which hold the
stand.

-8-
www.hanasis.com
5. Disconnect the cables as shown.
Cut the cable tie which holds the cable in place
ⒶInverter cable
ⒷTouch-board cable
Remove adhesive tape
ⒸLVDS cable
ⒹLED cable and OSD-board cable
ⒺInternal Speaker cable
Ⓚcable tie
6. Remove the screws(8ea).
7. Remove the front cover, and put down a clean place. 8. Undo screws(4ea) on the side of display bracket.
Disassembly and Assembly HDD MEMORY BOARD T/P,LCD MSR
Touch-panel and TFT-LCD Replacement

-9-
www.hanasis.com
- Be careful in case of any damage occurred to cables.
- Be careful in case of any breakage and injury.
-Be careful in case of any dust being stuck into the surface of LCD or touch panel and scratch to them.
-Plase use the anti-static fan preventing dust applied to the surface of LCD
Disassembly and Assembly HDD MEMORY BOARD T/P,LCD MSR
Touch-panel and TFT-LCD Replacement
1. Using a knife cut between the LCD and Touch panel.
2. Carefully cut the middle of cushion tape between LCD and Touch panel where you can see the gap.
3. Remove cushion tape completely on the corners of Touch panel.
4. Also remove cushion tape on the corners of LCD.
5. LCD(End of steel bezel) and Touch panel(inside the yellow line) are attached to match.
!

-10 -
www.hanasis.com
MSR Removal
1. Remove the screws(2ea). 2. Remove the MSR and Disconnect the MSR cable.
Disassembly and Assembly HDD MEMORY BOARD T/P,LCD MSR