Handife BX-6811 User manual

1 2 3
PROGRAM
DIGITAL HOSE END TIMER
BX-6811
NSTRUCTON MANUAL

PRODUCT OVERVIEW
1 2 3
PROGRAM
Local time
Set start time of watering
Set watering frequency
Set time of watering
P1P2P3 Three watering plans
Day of the week
Watering continues
Watering countdown
Min/Max Operating Pressure
1
Warning：Maximum operating pressure: 120PSI（8.2bar） For irrigation use only！
0.5bar-8.2bar (7.25 psi-120 psi)
Max Flow Rate 10 Gal/Min (35L/Min)
Waterproof Rate IP54
Working Temperature 3℃-50℃ (37.4℉-122℉)
Power 2 AAA (1.5V) alkaline
batteries(Excluded)
Adjustment
button +/-
Confirm the setting
battery power
ON/OFF Execute/stop
current time
Next watering time
Setting cycle
Show watering/do not show stop watering
T
j
1 2 3

2 X AA ALKALINE BATTERIES ARE RECOMMENDED (Batteries not included)
INSTALLING THE BATTERY
LOW BATTERY PROTECTION
Remove the battery cover-keep the battery compartment dry-install the 2XAA Battery by
lining up the connections.
Place the battery inside the compartment and reinstall the battery cover.
NOTE: When installing the battery, press the battery cover to the end. If the battery cover
is flush with the case, the battery cover is installed correctly. If the battery cover is higher
than the case, it means that it is not in place, and it may cause water ingress to
short-circuit on rainy days.
NOTE: When the battery is first connected. it takes up to 1 minute for the battery
indicator to assess the battery strength.
NOTE: Please use standard batteries that meet the quality requirements. Inferior batteries
will leak and corrode equipment.
NOTE: Remove the battery if the timer is not used for an extended time.
When the low battery indicator appears on display. the valve will close automatically to
avoid leakage. Please replace the battery in time in case of interrupting the normal
operation.
2

PROGRAM
PROGRAM
PROGRAM
PROGRAM
SET CLOCK: SETTING DAY&TIME
1
Set the current time.
Step 1: Press to wake up the screen and display all the information.
Step 1: Press to wake up the screen and display all the information, Press
repeatedly ,Choose a watering plan: P1,P2,P3
Step 2: Press Set the current hour: 00 (Flashing), Press +/- to adjust to the
exact hour: (0-23 hours)
NOTE: Long press +/- to quickly increase/decrease the value.
■ Press after confirming，At this time, other function buttons cannot be set, you
need to press again to enter the page; The screen displays all the information,
enter the next program setting.
■ If the screen will automatically go off after timeout, press any key to wake up and repeat the
above steps.
Step 5:Press to confirm to finish setting the current time: 00:02 Su
Step 4: Press Choose to set the day of the week: Su (flashing)；Press +/- to
adjust to the exact day of the week;(Mo:Monday; Tu:Tuesday; We:Wednesday; Th:Thurs-
day; Fr:Friday ; Sa:Saturday; Su:Sunday)；
Step 3: Press Select set minutes: 02 (Flashing)；Press +/- to adjust to the
exact minute (0-59 minutes)；
PROGRAMMING CYCLE
2
3

PROGRAM
PROGRAM
PROGRAM
PROGRAM
PROGRAM
PROGRAM
PROGRAM
PROGRAM
Step 2: Press Choose ON/OFF.(ON: The valve is opened and the watering plan is
executed, OFF: the valve is closed, and the watering plan is not executed.)
NOTE: If you need to close the P3 plan ,but P1 and P2 are executed normally,
NOTE:
■ If the screen goes off，Press to wake up the screen and display all the
information，Press repeatedly , Choose a watering plan: P1, P2, P3
NOTE
■ If the screen goes off，Press to wake up the screen and display all the
information，Press repeatedly , Choose a watering plan: P1
■ “ON P1” show in screen.
Step 1: Set watering frequency, Press to select the watering days. If the "Mo"
frame flashes to indicate that Monday is currently selected, Press ,The screen
shows that the“MO” surface was watered on Monday; Press , The disappearance
of "Mo" on the screen indicates that there will be no watering on Monday.
Step 2: Press ,Choose whether to water in other days; If the screen displays "Mo",
"We", "Sa", it means that the P1 watering plan is: watering in the time period set
on Monday, Wednesday and Saturday. Other times Do not water.
Step 1: Set the first time watering, Press to“P1” ,Press to “ON ”；“ON
P1”show in screen，At this time, you can set the watering plan P1.
Step 2: Press to set the start watering time：07:00. Press to set
hour/minute, Press add and subtract time. Press to confirm to
finish setting, You can also directly press or to set the next step and it will
be automatically saved.
Press to“P3”; Press to “OFF ”. （OFF P3）
Press to“P1”; Press to “ON ”; （ON P1）
Press to“P2”; Press to “ON ”; （ON P2）
SETING STARITTTME
SETTING HOW OFTEN
4

SETTING HOW LONG
PROGRAM
PROGRAM
PROGRAM
PROGRAM
PROGRAM
NOTE
■ If the screen goes off，Press to wake up the screen and display all the
information，Press repeatedly , Choose a watering plan: P1
NOTE
■ Press Choose a watering plan: P2 or P3，Set watering plan in the same way.
NOTE
■ These operate will not influence the automatic setting.(watering plan P1,P2,P3).
■ When it is watering as an automatic set. Press 3seconds, it can stop this time.(
The tap icon will disappear.)
NOTE: Please turn off the faucet before installation to avoid water splash.
Step 1: To instantly water：Press 3seconds until shown on screen.show in screen.
Step 2: Manually set the watering time: You can adjust water time by .
Step 3: After setting. Press to confirm. then when the time arrives, it will stop by itself.
■ “ON P1” show in screen.
Step 1: Press ,Choose how long to water，Press ,Choose Secs/Mins/Hrs；
Step 2: Press Increase/decrease the watering time. Press ，At this time, the
bottom right of the screen will display the countdown to the next watering.
MANUEL OPERATION
HOW TO INSTALL
1 2 3
PROGRAM
5

WARNING
① Maximum working pressure of sprinkler timer: 120PSI (8.2bar) for irrigation only!
② Please do not use water above 120°F (50°C) or below 38°F (3°C)!
③ Do not subject the sprinkler timer to excessive external force impact!
④ To avoid damaging your sprinkler timer, tighten the interface by hand. Tightening with tools
can easily damage the product!
⑤ Before installation, please make sure to set a gasket in the top connector to prevent leakage,
add a rubber gasket and threaded sealing tape if necessary!
⑥ The mesh filter prevents dirt particles from entering the sprinkler timer and extends its
service life. Clean the filter regularly, if it is worn, please replace it in time!
⑦ When the sprinkler timer screen is dim, it means that the battery is low, please replace the
battery in time, so as not to affect the normal operation of the product!
⑧ When not in use, please take out the battery, drain it and store it indoors!
⑨ When replacing the battery, make sure that the battery compartment is dry!
⑩ Do not immerse the product in water!
6

Email: [email protected]
Address: 202, 2/F, West Block, Laobing hengfang
Industrial Park, Xingye Road, Laodong Community,
Xixiang Subdistr, Bao'an District, Shenzhen
Company: Shenzhen Zestnation Technology Co.,Ltd.
-Thanks for choosing Handife-
MADE IN CHINA