Hanna Instruments HI 96814 User manual

HI96814
Refractometer for Sucrose
in Wine and Grape Products
Measurements
INSTRUCTION MANUAL

Thank you for choosing a Hanna Instruments product.
Please read this instruction manual carefully before using
this instrument.
This manual will provide you with the necessary information
for correct use of this instrument, as well as a precise idea
of its versatility.
If you need additional technical information, do not hesitate
to e‑mail us at [email protected] or view our worldwide
contact list at www.hannainst.com.
Dear
Customer,
All rights are reserved. Reproduction in whole or in part is prohibited
without the written consent of the copyright owner, Hanna Instruments
Inc., Woonsocket, Rhode Island, 02895, USA.

3
TABLE OF CONTENTS
Preliminary Examination .......................................................
General Description...............................................................
Specifications.......................................................................
Principle of Operation...........................................................
Functional Description...........................................................
Display Elements..................................................................
Measurement Guidelines .......................................................
Calibration Procedure............................................................
Measurement Procedure........................................................
To Change Measurement Unit................................................
To Change Temperature Unit .................................................
Making a Standard % Brix Solution ......................................
Battery Replacement.............................................................
Error Messages.....................................................................
Accessories...........................................................................
4
5
7
10
11
15
6
9
12
10
16
14
13
17
18

4
Remove the instrument from the packing materials and examine carefully
to ensure no damage has occurred during shipping. If any damage has
occurred, contact your local Hanna Instruments Office.
Each HI96814 instrument is supplied with:
• 9 V battery
• Instruction manual
• Plastic pipette
• Quality Certificate
Note: Save all packing material until you are sure that the instrument
functions correctly. A defective instrument must be returned in its
original packing.
PRELIMINARY EXAMINATION

5
The HI96814 Digital Wine Refractometer is rugged portable, water resistant
devices that benefit from Hanna Instruments’ years of experience as a
manufacturer of analytical instruments. Hanna Instruments offers five related
wine refractometers to fill the differing requirements found in the industry.
All are equally valid ways to measure the sugar content of grape or must
samples in the field or winery.
The HI96814 is optical instruments that are based on the measurement of
the refractive index of a solution. The measurement of refractive index is
simple and quick and provides the vintner a standard accepted method for
sugar content analysis. Samples are measured after a simple user calibration
with deionized or distilled water. Within seconds the instrument measures
the refractive index of the grape. These digital refractometers eliminate the
uncertainty associated with mechanical refractometers and are easily por‑
table for measurements in the field. Temperature (in °C or °F) is displayed
simultaneously with the measurement on the large dual level display along
with icons for Low Power and other helpful message codes.
Key features include:
• Dual‑level LCD
• Automatic Temperature Compensation (ATC)
• Easy setup and storage
• Battery operation with Low Power indicator (BEPS)
• Automatically turns off after 3 minutes of non‑use
• Single‑point calibration with distilled or deionized water
• Waterproof models offers IP65 waterproof protection
• Quick,preciseresultsreadingsaredisplayedinapproximately1.5 seconds
• Small sample size as small as 2 metric drops.
GENERAL DESCRIPTION

6
SPECIFICATIONS
Range
0.0 to 50.0 %Brix / 0 to 230 °Oechsle /
0.0 to 42.0 °KMW / 0.0 to 80.0 °C
(32.0 to 176.0 °F)
Resolution 0.1 %Brix / 1 °Oechsle /
0.1 °KMW / 0.1 °C (0.1 °F)
Accuracy ±0.2 %Brix / ±1 °Oechsle /
±0.2 °KMW / ±0.3 °C (±0.5 °F)
Temperature Compensation Automatic between 10.0 and 40.0 °C
(50.0 ‑ 104.0 °F)
Measurement Time Approximately 1.5 seconds
Minimum Sample Volume 100 µL (cover prism totally)
Light Source Yellow LED
Sample Cell Stainless Steel ring and flint glass prism
Case Material ABS
Enclosure Rating IP65
Battery Type / Life 9V / 5000 readings
Auto‑Off After 3 minutes of non‑use
Dimensions 192 x 102 x 69 mm (7.6 x 4.1 x 2.7”)
Mass 350 g (12.3 oz)

7
PRINCIPLE OF OPERATION
The measurement is made by determining the refractive index of a solution.
Refractive Index is an optical characteristic of a substance and the number of
dissolved particles in it. Refractive Index is defined as the ratio of the speed
of light in empty space to the speed of light in the substance. A result of
this property is that light will “bend”, or change direction, when it travels
through a substance of different refractive index. This is called refraction.
When passing from a material with a higher to lower refractive index, there
is a critical angle at which an incoming beam of light can no longer refract,
but will instead be reflected off the interface. The critical angle can be used
to easily calculate the refractive index according to the equation:
sin (θcritical) = n2/ n1
In the HI96814, light from an LED passes through a prism in contact with
the sample. An image sensor determines the critical angle at which the light
is no longer refracted through the sample.
Wheren2istherefractiveindexofthelower‑densitymedium;n1istherefractive
index of the higher‑density medium.

8
PRINCIPLE OF OPERATION
HI96814 converts the refractive index of the sample to sucrose concentration
in units of percent by weight, %Brix (also referred to as °Brix). The conversion
used is based on the ICUMSA Methods Book (International Commission for
UniformMethods of SugarAnalysis). Since themajority of sugarin grape juice
is fructose and glucose and not sucrose, the reading is sometimes referred
to as “Apparent Brix”.
In addition to %Brix, HI96814 includes two other scales used in the wine
industry: °Oechsle and °KMW.
°Oechsle (°Oe) is mainly used in the German, Swiss and Luxenburgish
winemaking industry to measure the sugar content of must. The °Oe scale is
based on specific gravity at 20 °C (SG20/20) and is the first 3 digits following
the decimal point. 1 °Oe is roughly equal to 0.2 %Brix.
°Oe = [(SG20/20) ‑ 1] x 1000
°Klosterneuburger Mostwaage (°KMW) is used in Austria to measure the
sugar content of must. °KMW is related to °Oe by the following equation:
°Oe = °KMW x [(0.022 x °KMW) + 4.54]
1 °KMW is roughly equivalent to 1 %Brix or 5 °Oe. °KMW is also known
as °Babo.

9
FUNCTIONAL DESCRIPTION
1. Liquid Crystal Display (LCD)
2. Secondary Display
3. Primary Display
4. READ Key (User Measurement)
5. ZERO Key (User Calibration)
6. RANGE Key (User Measurement Unit)
7. ON/OFF
8. Stainless Steel Sample Well and Prism
TOP VIEW
9. Battery Cover
10. Battery Compartment
BOTTOM

10
1. Battery (blinks when low battery condition detected)
2. Primary Display (displays measurement and error messages)
3. Measurement in Progress Tag
4. SETUP: Factory Calibration Tag
5. CAL: Calibration Tag
6. Measurement Units
7. Automatic Temperature Compensation
(blinks when temperature exceeds 10.0‑40.0 °C/50.0‑104.0 °F range)
8. Temperature Units
9. Secondary Display (displays temperature measurements; when blinking,
temperature has exceeded operation range: 0.0‑80.0 °C/32.0‑176.0 °F)
DISPLAY ELEMENTS
• Handle instrument carefully. Do not drop.
• Do not immerse instrument under water.
• Do not spray water to any part of instrument except the “sample well”
located over the prism.
• The instrument is intended to measure Wine and Grape products. Do not
expose instrument or prism to solvents that will damage it. This includes
most organic solvents and extremely hot or cold solutions.
• Particulate matter in a sample may scratch the prism. Absorb sample
with a soft tissue and rinse sample well with deionized or distilled water
between samples.
• Use plastic pipettes to transfer all solutions. Do not use metallic tools
such as needles, spoons or tweezers as these will scratch the prism.
• To reduce the effects of evaporation or absorption of water when taking
readings over a period of time, the prism and sample well can be covered
with plastic wrap.
MEASUREMENT GUIDELINES

11
3. Press the ZERO key. If no error messages appear, your unit is calibrated.
(For a description of ERROR MESSAGES see page 17).
Note: The 0.0 screen will remain until a sample is measured or the
power is turned off.
4. Gently absorb the ZERO water standard with a soft tissue. Use care not
to scratch the prism surface. Dry the surface completely. The instrument
is ready for sample measurement.
Note: If the instrument is turned off the calibration will not be lost.
Calibration should be performed daily, before measurements are made,
when the battery has been replaced, between a long series of measure‑
ments, or if environmental changes have occurred since the last calibration.
1. Press the ON/OFF key, then release. Two instrument test screens will
be displayed briefly; all LCD segments followed by the percentage of
remaining battery life. When LCD displays dashes, the instrument is ready.
2. Using a plastic pipette, fill the sample well with distilled or deionized
water. Make sure the prism is completely covered.
Note: If the ZERO sample is subject to intense light such as sunlight
or another strong source, cover the sample well with your hand or
other shade during the calibration.
CALIBRATION PROCEDURE

12
MEASUREMENT PROCEDURE
Verify the instrument has been calibrated before taking measurements.
1. Wipe off prism surface located at the bottom of the sample well. Make
sure the prism and sample well are completely dry.
4. Remove sample from the sample well by absorbing with a soft tissue.
5. Using a plastic pipette, rinse prism and sample well with distilled or
deionized water. Wipe dry. The instrument is ready for the next sample.
Note: The last measurement value will be displayed until the next
sample is measured or the instrument is turned off. Temperature
will be continuously updated.
The ATC tag blinks and automatic temperature compensation
is disabled if the temperature exceeds the 10.0-40.0 °C/
50.0-104.0 °F range.
3. Press the READ key. The result is displayed in in the selected units.
2. Using a plastic pipette, drip sample onto the prism surface. Fill the well
completely.
Note: If the temperature of the sample differs significantly from
the temperature of the instrument, wait approximately 1 minute to
allow thermal equilibration.

13
Press the RANGE key to select measurement units %Brix, °Oechsle (°Oe)
or °KMW (°Babo). The instrument toggles between the three scales each
time the key is pressed and the primary display indicates “bri” for %Brix,
“OE” for °Oechsle or “bAbo” for °KMW. When the instrument displays the
screen with 4 dashes the instrument is ready for measurement.
TO CHANGE MEASUREMENT UNIT

14
TO CHANGE TEMPERATURE UNIT
To change the temperature measurement unit from Celsius to Fahrenheit
(or vice versa), follow this procedure.
1. Press and hold the ON/OFF key continuously for approximately
15 seconds. The LCD will display the “all segment” screen followed by
a screen with the model number on the primary display and the version
number on the secondary display. Continue pressing the ON/OFF key.
2. While continuing to hold the ON/OFF key, press the ZERO key. The
temperature unit will change from °C to °F or vice versa.
15 seconds
°C or °F

15
Note:Solutions above60 %Brix needto bevigorously stirredor shaken
and heated in a water bath. Remove solution from bath when sucrose
hasdissolved.Thetotalquantitycanbe scaled proportionallyfor smaller
containers but accuracy may be sacrificed.
Example with 25% Brix:
%Brix g Sucrose g Water g Total
25 25.000 75.000 100.000
To make a Brix Solution, follow the procedure below:
•Place container (such as a glass vial or dropper bottle that has a cover)
on an analytical balance.
•Tare the balance.
•To make an X % BRIX solution weigh out X grams of high purity Sucrose
(CAS #: 57‑50‑1) directly into the container.
•Add distilled or deionized water to the container so the total weight of
the solution is 100 g.
MAKING A STANDARD % BRIX SOLUTION

16
To replace the instrument’s battery, follow these steps:
• Make sure the instrument is off.
• Turn instrument upside down and remove the battery cover by turning
it counterclockwise.
BATTERY REPLACEMENT
• Extract the battery from its location.
• Replace with a new 9V battery making sure to observe polarity.
• Insert the back battery cover and fasten it by turning clockwise to
engage.

17
ERROR MESSAGES
Error Code Description
“Err“ General failure. Cycle power to instrument.
If error persists, contact your local Hanna
Instruments Office.
“LO“ primary
display
Sample exceeds minimum measurement
range.
“HI“ primary
display
Sample exceeds maximum measurement
range.
“LO“ primary
display Cal
segment ON
Wrong solution used to zero instrument.
Use deionized or distilled water. Press
ZERO.
“HI“ primary
display Cal
segment ON
Wrong solution used to zero instrument.
Use deionized or distilled water. Press
ZERO.
“t LO“ primary
display Cal
segment ON
Temperature exceeds ATC low limit
(10.0 °C) during calibration.
“t HI“ primary
display Cal
segment ON
Temperature exceeds ATC high limit
(40.0 °C) during calibration.
“Air“ Prism surface insufficiently covered.
“ELt“ Too much external light for measurement.
Cover sample well with hand.
“nLt“ LED light is not detected.
Contact your local Hanna Instruments
Office.
Battery segment
blinking
<5% of battery life is remaining.
Temperature values
are blinking
“0.0°C“ or“80.0 °C“
Temperature measurement
out of range (0.0 to 80.0 °C).
ATC segment
blinking
Outside temperature
compensation range
(10.0 to 40.0 °C).
SETUP segment
blinking
Factory calibration lost.
Contact your local Hanna Instruments
Office.

18
MAN96814 04/17
ACCESSORIES
Code Description
HI4020-11 50% Brix Standard, 10 mL
HI740157P Plastic refilling pipette (20 pcs.)
HI740029P 9V Battery (10 pcs.)

HI96814 is warranted for two years against defects in
workmanship and materials when used for their intended
purpose and maintained according to instructions.
This warranty is limited to repair or replacement free of
charge.
Damage due to accidents, misuse, tampering or lack of
prescribed maintenance is not covered.
If service is required, contact your local Hanna Instruments
Office. If under warranty, report the model number, date
of purchase, serial number and the nature of the problem.
If the repair is not covered by the warranty, you will be
notified of the charges incurred. If the instrument is to be
returned to Hanna Instruments, first obtain a Returned Goods
Authorization number from the Technical Service department
and then send it with shipping costs prepaid. When ship‑
ping any instrument, make sure it is properly packed for
complete protection.
To validate your warranty, fill out and return the enclosed
warranty card within 14 days from the date of purchase.
Warranty
Hanna Instruments reserves the right to modify the design, construction or
appearance of its products without advance notice.

Printed in ROMANIA
World
Headquarters
Hanna Instruments Inc.
Highland Industrial Park
584 Park East Drive
Woonsocket, RI 02895 USA
www.hannainst.com
Local Office
Hanna Instruments USA
270 George Washington Highway
Smithfield, RI 02917
Phone: [phone]
Fax: [phone]
e‑mail: [email protected]
MAN96814