OPERATIONAL GUIDE
To connect the probe
Connect the FC 202D probe to the DIN socket on the top of
themeterbyaligningthepinsandpushingintheplug.Tighten
the nut to ensure a good connection. Remove the protective
cap from the probe before taking any measurements.
To turn the meter on and to check battery status
Press and hold the ON/OFF/MODE button for 2 seconds. All
the used segments on the LCD are visible for a few sec-
onds, followed by a percent indication of the remaining bat-
tery life (e.g. % 100 BATT).
To freeze the display
Press and hold the SET/HOLD button, until HOLD appears
on the bottom display. The reading will be frozen on the LCD
(e.g. pH 5.73 HOLD).
Press any button to return to normal mode.
To turn the meter off
From normal measuring mode, press ON/OFF/MODE. OFF
appears on the bottom display. Release the button.
pH MEASUREMENT & CALIBRATION
• Make sure the meter has been calibrated before use.
• If the electrode has been left dry, soak it in HI 70300 stor-
age solution for one hour to reactivate.
• Insert the tip of the probe in the sample to be tested.
• Wait until the stability indicator on the LCD is turned off.
• The LCD shows the pH value automatically compensated
for temperature and the temperature of the sample.
• If measurements are taken in different samples succes-
sively, clean the probe tip thoroughly to eliminate cross-
contamination. For cleaning procedure choose the suit-
ableHanna cleaning solution (see“Accessories”section).
pH calibration
• Pressand hold the ON/OFF/MODE button, untilOFFon the
bottom display is replaced by CAL.
• Release the button. The LCD displays “pH 7.01 USE” or
“pH 6.86 USE” (if you selected the NIST buffer set).
• For a
single point pH calibration
, place the probe in any
buffer from the selected buffer set (eg. pH 7.01 or pH 4.01
orpH10.01). The meter automatically recognizes the buffer
value and displays OK for 1 second.
If the pH 7.01 buffer (or 6.86 if you selected the NIST buffer
set) was used, press the ON/OFF/MODE button to return to
the pH measuring mode.
• For a
two point pH calibration
, place the probe in pH 7.01
(or 6.86, if you selected the NIST buffer set). The LCD dis-
plays the recognized buffer value and OK for 1 second and
then “pH 4.01 USE”.
Place the probe in the second buffer solution (pH 4.01 or
10.01, or, if using NIST, pH 4.01 or 9.18). When the second
buffer is recognized, the LCD displays OK for 1 second
and the meter returns to normal measuring mode.
To reset to the default calibration
To clear a previous calibration, press the ON/OFF/MODE
button after entering the calibration mode. The bottom LCD
displays ESC for 1 second and the meter returns to normal
measuring mode. The “CAL” symbol on the LCD disappears
and the meter resets to the default calibration.
METER SETUP
• Press and hold the ON/OFF/MODE button for about 6 sec-
onds, until CAL on the bottom display is replaced by TEMP
and the current temperature unit (e.g. TEMP °C). Then:
•
for °C/°F selection
, use the SET/HOLD button. After the
temperature unit has been selected, press ON/OFF/MODE
toenterthe buffersetselectionmode;pressON/OFF/MODE
twice to return to the normal measuring mode.
•
to change the calibration buffer set
, after setting the tem-
perature unit, the meter will show the current buffer set: pH
7.01 BUFF (for 4.01/7.01/10.01) or pH 6.86 BUFF (for 4.01/
6.86/9.18).Changetheset with the SET/HOLD button, then
press ON/OFF/MODE to return to normal mode.
BATTERY REPLACEMENT
The meter displays the remaining percentage when turned
on. When the battery level is below 5%, the
symbol on the
bottom left of the LCD lights up to indicate a low battery con-
dition. If the battery level is low enough to cause erroneous
readings, the Battery Error Prevention System (BEPS) turns
the meter off.
The batteries are accessed by separating the front and back
halves of the meter. Unscrew the 4 screws located on the
back of the meter. Remove the back and carefully replace all
the four AAA batteries located in the battery compartment,
while paying attention to their polarity.
Re-attach the back, making sure that the gasket is in place to
ensure a watertight seal
.
WARRANTY
All Hanna Instruments meters are warranted for two years
against defects in workmanship and materials when used for their
intended purpose and maintained according to instructions. The
probes are warranted for a period of six months.
This warranty is limited to repair or replacement free of charge.
Damages due to accident, misuse, tampering or lack of prescribed
maintenance are not covered.
If service is required, contact the dealer from whom you purchased
the instrument. If under warranty, report the model number, date of
purchase, serial number and the nature of the problem. If the repair
is not covered by the warranty, you will be notified of the charges
incurred. If the instrument is to be returned to Hanna Instruments,
first obtain a Returned Goods Authorization Number from the Cus-
tomer Service department and then send it with shipment costs
prepaid. When shipping any instrument, make sure it is properly
packaged for complete protection.
