BROSA Memphis Entertainment Unit User manual

Memphis
Entertainment Unit
A S S E M B LY GU I D E
V1

FOR YOUR SAFETY
Lift, don’t drag. This protects
your floor and product.
Avoid loose screws. Tighten
fixtures every few months.
Assembly requires 2 people.
It's always easier with a
friend.
Contact our support online
or call 1300 027 672.
Check the assembly guide
for required components.
?
Assembling this product on
a soft surface protects its
finish.

Components
Before you get started, check you have all of the pieces below.
If anything’s missing, we’ll sort it out right away. Simply visit:
www.brosa.com.au/pages/product-return-and-parts-request
Hardware
A x 4
(M6 x 10)
B x 6
(M6 x 16)
C x 10
(Ø8 x Ø16)
D x 1
Body x 1
②
Middle Rail x 1
④
Leg Frame x 2
③
Top x 1
①

Step 1 Fit the metal arm of the leg frame ③into the
centre of the middle rail ④. Repeat this for the
other leg frame.
Make sure the stickers on both components
match as shown in the diagram.
④
③
③

Step 2 Fit a washer C to a short bolt A. Insert the short
bolt into a hole on the middle rail. Screw the bolt
with your hand. Leave the bolt loosely attached.
Repeat this for the holes on the other side of the
rail.
A x 4
C x 4
AC

Step 3 Align the structure formed in Step 2 with the
holes on the bottom of the body ②. Make sure
the stickers match as per the diagram below.
Fit a washer C to a long bolt B. Insert the bolt into
a hole on the leg frame. Screw the bolt with your
hand and leave it loosely attached. Repeat this
for all holes on the leg frames.
B x 6
C x 6
②
B
C

Step 4 Once the structure is built up, tighten all bolts
with the Allen key D.
D x 1
D
D

Step 5 Flip the completed structure the right way up and
place it in its desired location.
Place the top ① upon the body.
①

Step 6 Enjoy your new Memphis Entertainment Unit!

It is not mandatory but strongly recommended to install anti-tip kit for
safety.
Anti-Tip Kit Installation
Hardware
Wall Fixings
a x 4 b x 2 cx 4 dx 4 ex 4
Wood
If fixing to wood
make sure that it
isn’t chipboard as
screws can easily
pull away from the
core structure.
Brick or Masonry
Use an appropriate
wall plug provided
you are sure your
wall is sound.
Cavity Wall
Special toggle wall
plugs are needed.
Seek expert
advice.
Because of the variety of wall compositions, we can’t provide you with
appropriate wall fixings. Please identify your wall composition and
contact your local hardware store to get the appropriate fixings.

What You Need
Attach the brackets a securely to the back top of the
product using the short screws cprovided.
Step 1
ax 2
cx 4
ac

Determine where the piece is to be placed and mark
locations on the wall for the mounting brackets ausing a
pencil. Move the furniture out of the way so that the
brackets can then be mounted to the wall.
Step 2
Instructions below demonstrate how to attach the kit to the wall using
the wall plugs provided. But please do identify the type of your wall
and choose the appropriate wall fixings.
ax 2
a

Drill holes for the wall plugs using a drill. Knock the plugs
e into the holes using a hammer. Place the brackets
against the plugs again and fix the brackets with the long
screws d.
Step 3
dx 4
ex 4
d
e

Lace the nylon strap b down through the brackets. Slide
the thin end of the strap through the receiving end on
the nylon strap. Pull to tighten the piece of furniture snug
against wall.
Step 4
bx 2
b

1. Upon receiving your product, you might find that the door doesn’t
align well. Please note that it’s not a product flaw and can be adjusted
following the instructions below.
Troubleshooting

Loosen the screw at the end of the hinge arm.
Step 1
Gently pull the door so that it is separated from the
body.
Step 2
2. Follow the steps below to disassemble your doors when needed.
Reverse the steps above to get the doors attached again.

User Recommendation
Assembly
1. Assemble furniture using our Assembly Guides. You can find them at
support.brosa.com
2. Do not dispose of any packaging or contents of the shipping carton
until assembly is completed to avoid accidentally discarding small
parts or hardware.
Materials
Brass
Brass is a natural material and as such may tarnish over time. This can
be brought on through regular use or temperature and environment
change. To reduce the look of tarnishing and return your brass to its
original colour, please use the soft scotch pad to gently rub the
affected area and surrounding areas. You can then apply a clear wax or
PU lacquer to protect the surface again. All products are previously
treated with PU lacquer to help reduce the risk of tarnishing.
Marble
1. Marble is a natural product, with unique, one-of-a-kind features.
Each piece varies slightly.
2. For furniture with marble components, the natural marble has unique
natural stone grains, and these grains look very similar to cracks. They
should not be considered flaws, but present their beautiful and unique
texture.
Placement
1. Keep furniture on flat, level ground. Placing it unevenly may cause
deformation.
2. Do not place heavy objects on furniture.
3. When repositioning furniture always lift, don’t drag.
4. Keep sharp objects away. They cause scratches and splinters to the
surface.
5. Do not stack furniture.

Cleaning and Maintenance
1. Clean furniture regularly with a white soft cloth. Slightly damp fabrics
help absorb dust, but remember to dry it once you’re done.
2. Clean spills and stains immediately with a clean cloth. As long as
you’re on hand to wipe up any spills straight away, you shouldn’t
encounter any problems.
3. Keep liquids away as they may damage the finishing.
4. Avoid harsh cleaning chemicals such as alcohol or gasoline
solvents. Avoid using sponges or dirty cloths.
5. Cover furniture that isn’t being used to protect from dust and
ageing.
6. Re-tighten screws and attachments if they loosen.
Exposure
1. Use protective coasters and mats for hot items on the furniture.
2. Keep furniture away from intense direct sunlight. Exposure can
cause cracks or discolouration.
3. Severe changes in temperature and humidity can accelerate ageing.
Keep furniture at least 60cm from heating or air conditioning.
4. Do not place furniture near open flames.