Hanover BRIGDN5PCBR User manual

Hanover Outdoor Furniture
6/1/2015 (b)
To expedite any future warranty claims, please retain the Instruction Sheet, Warranty
Card and receipt for future use.
Care and Maintenance
Store furniture in an upright position. Be careful to never allow water to build up in frames as this will
cause corrosion and freeze damage in cold climates. Wash all frames with a solution of mild soap and
water. Rinse with clean water and dry with a soft absorbent cloth towel. Frames can be treated with a
liquid wax for maximum protection against UV rays and/or salty, damp air. If your set includes
cushions, slings, and/or an umbrella they may be cleaned by hand with a solution of soap and water
with a clean water rinse. (Never machine wash cushions, slings or umbrella covers as this will result in
shrinkage or damage). After cleaning cushions tip on end and allow to drip dry. (Never use a
commercial or home dryer to tumble dry fabric goods). Do not use bleach or solvents to clean any
product! This will void the warranty.
For additional on‐line support on assembly, troubleshooting and care & maintenance of your outdoor
furniture, please visit our website at: www.hanover‐products.com.
IMPORTANT
If you have any problems with this product (missing or damaged parts, assembly issues, etc.),
PLEASE DO NOT RETURN TO THE RETAILER/STORE
from where you purchased the product.
Please call our Toll‐Free Customer Service Hotline at: 1-877-397-5144
Between 9:00 AM and 5:00 PM Eastern Time, Monday through Friday
Or visit our website at: www.hanover‐products.com

High Dining Table
Owner's Manual
If you have any problems with this product, DO NOT RETURN IT TO THE STORE
CALL OUR CUSTOMER SERVICE HOT-LINE AT
1-877-397-5144
Between 9 A.M. - 5 P.M. Eastern Time, Monday through Friday
Page 1of 7

Page 4 of 7

PART# DESCRIPTION PICTURE QTY
A Table top 1
B Table leg 4
C Support Tube 8
D Connector 1
AA M6 x15mm 4
BB Bolt M6 x18mm 16
CC Bolt M6 x 35mm 16
DD Washer 36
EE Bolt Cover 36
FF Wrench 1
Page 5 of 7
PARTS LIST

Assembly Steps:
Note: Do not fully tighten bolts until assembly is completed and alignment is correct.
Step 1. Assemble the connector (D) to the table leg (B) with bolts (AA) and washer (DD)
as shown in figure 1.
Figure 1
Step 2. Carefully place the table top (A) upside down on a non-abrasive surface.
Step 3. Assemble the table legs (B) to the table top (A) with bolts (BB) and washer (DD)
as shown in figure 2.
Page 6 of 7
Figure 2

Step 4. Loosely attach the support tube (C) to the table leg (B) and table top (A) with
bolts (CC) and washer (DD) as shown in figure 3.
Step 5. Check the alignment and adjust if necessary. Once the alignment is correct, tighten
all bolts with wrench (FF) . Cover all bolts with bolt caps(EE).
Figure 3
Step 6. Verify all bolts are securely tightened before use and turn your table right side up.
Your table is now ready to use. (Figure 4).
Figure 4
Page 7 of 7

High Dining Swivel Chair
Owner's Manual
If you have any problems with this product, DO NOT RETURN IT TO THE STORE
CALL OUR CUSTOMER SERVICE HOT-LINE AT
1-877-397-5144
Between 9 A.M. - 5 P.M. Eastern Time, Monday through Friday
Page 1 of 7

PART# DESCRIPTION PICTURE QTY
A Chair Frame 1
B T Rocker 1
C Base 1
D Steel Panel 2
AA Bolt M8 x 45mm 4
BB M8 Washer 8
CC M8 Spring Gasket 4
DD M8 Nut 4
EE M8 Bolt Cover 4
FF Bolt Cover For M8
Nut 4
GG Open Wrench 1
PARTS LIST
Page 5 of 7

Assembly Steps:
Note: Do not fully tighten bolts until assembly is completed and alignment is correct.
Step 1. Carefully place the chair frame (A) upside down on a non-abrasive surface.
Assemble the T rocker(B) to the chair frame(A) with steel panel(D) and Bolts(AA) and
Washer(BB) and M8 Spring gasket (CC) and M8 Nut(DD) by using open wrench(GG),
then cover the bolts with bolt covers (EE and FF) as shown in Figure 1.
Figure 1
Step 2. Place the chair frame (A) into the base( C ) as shown in Figure 2 .
Figure 2
Page 6 of 7

Step 3. Your chair is now ready to use. (Figure 3).
Figure 3
Page 7 of 7