Hanover BCS01807 User manual


HanoverOutdoorFurniture




IMPORTANT
Ifyouhaveanyproblemswiththisproduct(missingordamagedparts,assemblyissues,etc.),
PLEASEDONOTRETURNTOTHERETAILER/STORE
fromwhereyoupurchasedtheproduct.
PleasecallourToll‐FreeCustomerServiceHotlineat:1‐800‐416‐3511
Between9:00AMand5:00PMEasternTime,MondaythroughFriday
Orvisitourwebsiteat:www.hanover‐products.com


Toexpediteanyfuturewarrantyclaims,pleaseretaintheInstructionSheet,Warranty
Cardandreceiptforfutureuse.
For additionalon‐linesupportonassembly,troubleshootingandcare&maintenanceofyouroutdoor
furniture,pleasevisitourwebsiteat:www.hanover‐products.com.
6/1/2015(a)

BCS01807
8
5
4
5/16" X 52 MM BOLT HW0128
HW0004
Ø6.5 X 1.0 MM
WASHER
Ø15X4MM
PLASTIC WASHER
PARTS LIST DESCRIPTION QTY ORDER PART #
A1
A2
B
C1
C2
D
E
F
G
H
I
J
K
L
M
GLIDER BASE
LEFT LEG
1
GLIDER BASE
RIGHT LEG
1
GLIDER LEG
SUPPORT BAR
2
GLIDER LEFT ARM
GLIDER RIGHT ARM
1
1
GLIDER BACK FRAME
GLIDER SEAT FRAME
1
1
1/4" X 45 MM BOLT
8
5/16" X 35 MM BOLT HW0128
HW0079
2
1/4" X 15 MM BOLT HW0112
1
32
HW0176
Ø8.5 X 1.5 MM
WASHER
HW0020
1/4" X 65 MM BOLT HW0111
2
4
4
25
PARTS LIST DESCRIPTION
1/4" NUT HW0017
1/4" NUT COVER
BOLT COVER
QTY
ORDER PART #
HW0006
HEX BOLT DRIVER
HEX WRENCH
1
1
FOOT CAP
FACTORY ASSEMBLY FC0165
GLIDER BRACKET
FACTORY ASSEMBLY
LEG CAP
FACTORY ASSEMBLY
4
Ø15X6MM
PLASTIC WASHER
N
O
P
Q
R
S
T
U
V
HW0033
16
5/16" NUT HW0177
5/16" NUT COVER
12
G0121
FC0051
HW0241
HEX WRENCH
1
HW0009
HW0022
HW0027
HW0178
* NOTE: PARTS SHOWN ON PARTS LIST ARE NOT TO SCALE

Fig.1
Fig.2
A1
D
A2
C1
C2
E
B
E
D
K
J
Q
L
G
Q
I
Q
L
PS
Q
G
L
L
G
Q
QGL
Step 1:
IMPORTANT NOTE: WE RECOMMEND TWO PEOPLE WORK TOGETHER TO ASSEMBLE THE GLIDER
Remove all protective materials and set parts on a flat, non-abrasive surface. Identify parts packed in carton against the parts list. If you are missing
any parts or are unsure how to proceed with assembly,
Assembly references to "left" and "right" are designated by facing the glider and NOT by sitting in it
please call our Product Specialists immediately at . Do not attempt to assemble
the chair if any parts are damaged or missing.
1-800-491-4958
Attach glider base left leg (A1) to one of the glider base leg support bars (B) using 5/16"x35 mm bolts (I) 8.5x1.5 mm washers (L), and 5/16" nuts (P)
as shown in . Repeat on glider base right leg (A2). Repeat entire procedure for remaining glider base leg support bar (B).
Attach glider back frame (D) to glider left arm (C1) using 5/16"x52 mm bolts (G), 8.5x1.5 mm washers (L) and 5/16" nuts (P) as shown in . Attach
seat frame to left arm using 5/16"x52 mm bolts (G), 8.5x1.5 mm washers (L) and 5/16" nuts (P) as shown in . Repeat to
attach glider seat back (D) and glider seat frame (E) to glider right arm (C2). Attach glider back frame and glider seat frame using a 1/4"x15 mm bolt (J)
and a 6.5 x 1.0 mm washer (K) as shown in . Guide bolt and washer through pre-drilled hole in glider seat frame and into pre-drilled hole on glider
back frame.
Step 2:
Do not over tighten.
Step 3:
Do not over tighten.
Do not over tighten.
Fig.1
Fig.2
Fig.2
Fig.3
E
E
E
L
LP
LP
LPS
S
LP
Q
R
Q
R
Fig.3
GLIDER BRACKET

Q
Q
F
N
N
H
Place the completed seat assembly over the glider base assembly. Use 1/4"x65 mm bolts (F) to attach back portion of seat assembly to rear glider
bracket on glider base. From the outside of the glider bracket, insert bolt (F) inward in this exact order through: glider bracket / 15x6 mm washer (N)
/ glider seat frame (E) / 15x4 mm washer (M) / 6.5x1.0mm washer (K) / 1/4" nut (O) as shown in . Use 1/4"x45mm
bolts (H) to attach front portion of seat assembly to front glider bracket on glider base. From the outside of the glider bracket, insert bolt (H) inward in
this exact order through: glider bracket / 15x6 mm washer (N) / glider seat frame (E) / 15x4 mm washer (M) / 6.5x1.0 mm washer (K) / 1/4" nut (O)
as shown in Repeat entire on opposite side.
Using hex wrench and hex bolt driver provided, tighten all nuts and bolts a few revolutions at a time, alternating between glider bracket connections
until all nuts and bolts are completely tight. Test of operation of glider. Gliding motion should be smooth. Adjust tension on
the glider brackets, nuts and bolts as needed. If nuts and bolts are either too tight or too loose, the glider will not function properly.
Cover all nuts and bolts with PVC covers provided. Your glider is now ready for use.
Step 4:
Do not over tighten.
Do not over tighten. Step 4
Step 5:
Do not over tighten.
1-800-491-4958
E
EE
EE
Fig.4
Fig.5
IMPORTANT NOTE: Damage to welds or frames resulting from over tightened bolts or improper assembly is not covered under our warranty.
Please read all instructions carefully before assembly. If you have any questions regarding your assembly, call our Product Specialists at
.
Fig.4
Fig.5
M
O
K
M
O
K