Hanover High Dining Table User manual

HanoverOutdoorFurniture
IMPORTANT
Ifyouhaveanyproblemswiththisproduct(missingordamagedparts,assemblyissues,etc.),
PLEASEDONOTRETURNTOTHERETAILER/STORE
fromwhereyoupurchasedtheproduct.
PleasecallourToll‐FreeCustomerServiceHotlineat:1‐866‐851‐8438
Between9:00AMand5:00PMEasternTime,MondaythroughFriday
Orvisitourwebsiteat:www.hanover‐products.com
Toexpediteanyfuturewarrantyclaims,pleaseretaintheInstructionSheet,Warranty
Cardandreceiptforfutureuse.
For additionalon‐linesupportonassembly,troubleshootingandcare&maintenanceofyouroutdoor
furniture,pleasevisitourwebsiteat:www.hanover‐products.com.
6/1/2015(b)

Page 3 of 7

Page 4 of 7

Owner's Manual
High Dining Table
Page 1 of 7
If you have any problems with this product, DO NOT RETURN IT TO THE STORE
CALL OUR CUSTOMER SERVICE HOT-LINE AT
1-866-851-8438
Between 9 A.M. - 5 P.M. Eastern Time, Monday through Friday

PART# DESCRIPTION PICTURE QTY
A Table top frame 1
B Table leg 4
C Connector 1
D Glass 1
AA Bolt M6 x 15mm 8
BB Bolt M6 x 25mm 8
CC Washer 16
DD Bolt Cover 16
EE Wrench 1
PARTS LIST
Page 5 of 7

Assembly Steps:
Note: Do not fully tighten bolts until assembly is completed and alignment is correct.
Step 1. Carefully place the table top frame (A) upside down on a non-abrasive surface.
Step 2. Assemble the table legs (B) to the table top (A) with bolts (AA) and washer (CC) as
shown in figure 1.
Figure 1
Step 3. Assemble connector (C) to the table leg (B) with bolts (BB) and washer (CC)
as shown in figure 2.
Step 4. Tighten all bolts with wrench (EE) . Cover all bolts with bolt caps(DD).
Figure 2
Page 6 of 7

Step 5. Verify all bolts are securely tightened before use and turn your table right side up.
Put glass (D) on table top frame(A). Your table is now ready to use. (Figure 3).
Figure 3
Page 7 of 7

High Dining Swivel Chair
Owner's Manual
If you have any problems with this product, DO NOT RETURN IT TO THE STORE
CALL OUR CUSTOMER SERVICE HOT-LINE AT
1-866-851-8438
Between 9 A.M. - 5 P.M. Eastern Time, Monday through Friday
Page 1 of 7

PART# DESCRIPTION PICTURE QTY
A Chair Frame 1
B T Rocker 1
C Base 1
D Steel Panel 2
E Seat Cushion 1
F Back Cushion 1
AA Bolt M8 x 45mm 4
BB M8 Washer 8
CC M8 Spring Gasket 4
DD M8 Nut 4
EE M8 Bolt Cover 4
FF
Bolt Cover For M8 Nut
4
GG Open Wrench 1
PARTS LIST
Page 5 of 7

Assembly Steps:
Note: Do not fully tighten bolts until assembly is completed and alignment is correct.
Step 1. Carefully place the chair frame (A) upside down on a non-abrasive surface.
Assemble the T rocker(B) to the chair frame(A) with steel panel(D) and Bolts(AA) and
Washer(BB) and M8 Spring gasket (CC) and M8 Nut(DD) by using open wrench(GG),
then cover the bolts with bolt covers (EE and FF) as shown in Figure 1.
Figure 1
Step 2. Place the chair frame (A) into the base( C ) as shown in Figure 2 .
Figure 2
Page 6 of 7

Step 3. Put seat cushion( E ) and back cushion ( F ) in chair.
Your chair is now ready to use. (Figure 3).
Figure 3
Page 7 of 7