Hanover ACL00106 User manual


HanoverOutdoorFurniture




IMPORTANT
Ifyouhaveanyproblemswiththisproduct(missingordamagedparts,assemblyissues,etc.),
PLEASEDONOTRETURNTOTHERETAILER/STORE
fromwhereyoupurchasedtheproduct.
PleasecallourToll‐FreeCustomerServiceHotlineat:1‐800‐416‐3511
Between9:00AMand5:00PMEasternTime,MondaythroughFriday
Orvisitourwebsiteat:www.hanover‐products.com


Toexpediteanyfuturewarrantyclaims,pleaseretaintheInstructionSheet,Warranty
Cardandreceiptforfutureuse.
For additionalon‐linesupportonassembly,troubleshootingandcare&maintenanceofyouroutdoor
furniture,pleasevisitourwebsiteat:www.hanover‐products.com.
6/1/2015(a)

Step 1:
Step 2:
Step 3:
IMPORTANT NOTE: Damage to welds or frames resulting from over tightened bolts or improper
assembly is not covered under our warranty. Please read all instructions carefully before assembly.
Identify all parts packed in carton against the parts list. Remove all protective materials. Place parts
on a non-abrasive surface to avoid scratching. I
,addanutwith
,addanutwith
Your sectional sofa is now ready for use.
f you are missing any parts or are unsure how to proceed
with the assembly, call our Customer Service Center at 1-800-416-3511.
1/4"x48 mm
1/4"x68 mm
After making any necessary adjustments to the alignment of the frames, use the hex bolt driver and
hex wrench to tighten all nuts and bolts. . Over tightening may strip bolts. Cover
all nuts and bolts with covers.
Do not attempt assembly if
any parts are missing or damaged.
Fig.1
Fig.2
Step 4:
Do not over tighten
Attach the seat frame to the left chair frame by using three bolts and washers as shown
in . Guide bolts through holes in the seat frame and left chair frame washer to
each bolt. Repeat for the right chair frame.
Attach the back frame to the left chair frame by using two bolts and washers as shown
in . Guide bolts through holes in the back frame and left chair frame washer to
each bolt. Repeat for the right chair frame.
Hand tighten only.
Hand tighten only.
If you
have any questions regarding your assembly, call our Customer Service Center at 1-800-416-3511.
*NOTE:PARTSSHOWNONPARTSLISTARENOTTOSCALE
G
H
I
FJ
G
G
H
I
EJ
G
PART LIST DESCRIPTION ORDER PART # QTY
1/4" NUT 10
HW0014
FC0030
HEX BOLT DRIVER HW0006 1
FOOT CAP
FACTORY ASSEMBLY
10
BOLT COVER HW0105
NUT COVER
10
HW0027
HEX WRENCH 1
HW0009
RIGHT CHAIR
FRAME
1
A
B
C
D
E
F
G
1/4" X 48 MM BOLT
Ø6.5 X 1.0 MM
WASHER
PART LIST DESCRIPTION ORDER PART # QTY
HW0004
HW0274
6
20
1
1/4" X 68 MM BOLT
HW0447
4
1
1
LEFT CHAIR
FRAME
BACK FRAME
SEAT FRAME
H
I
J
K
L
B
Fig.1
Fig.2
IMPORTANT!! PLEASE READ ENTIRE INSTRUCTION SHEET BEFORE ASSEMBLY!!
TO EXPEDITE ANY FUTURE WARRANTY CLAIMS, PLEASE KEEP INSTRUCTION SHEET, WARRANTY CARD AND RECEIPT
ACL00106
A
D
FOOT CAP
C
Page 2

ACL00108
IMPORTANT!! PLEASE READ ENTIRE INSTRUCTION SHEET BEFORE ASSEMBLY!!
TO EXPEDITE WARRANTY CLAIMS PLEASE KEEP INSTRUCTION SHEET, WARRANTY CARD AND COPY OF RECEIPT
Page 2
Step 1:
Do not attempt assembly if any parts are missing or damaged.
Step 2:
Hand tighten only.
Hand tighten only.
Hand tighten only.
Step 3:
Do not over tighten
Step 4:
Remove all protective materials and set parts on a flat, non-abrasive surface. Identify parts packed in carton against the
parts list. If you are missing any parts or are unsure how to proceed with assembly, call our Customer Service Center
at 1-800-416-3511.
Place the ottoman top upside down on a flat, non-abrasive surface. Attach a ottoman leg-1 to the ottoman top by using
two bolts and washers as shown in . Guide the bolt through the hole in the leg-1, into the pre-drilled hole in
the table rim. Repeat for the other leg-1. Attach a ottoman leg-2 to the ottoman top by using three
bolts and washers as shown in . Repeat for the other leg-2. Attach a ottoman leg-3 to the
ottoman top by using three bolts and washers as shown in .
After making any necessary adjustments to the alignment of the legs and the ottoman top bracket, use hex bolt driver to
tighten all bolts. . Over tightening may strip bolts or damage the welds or frame. Cover all bolts
with covers.
At the time, turn the table in the upright position. Your ottoman is now ready for use. If you have any questions, please
call our Customer Service Center at 1-800-416-3511.
Figure 1
Figure 2
Figure 3
IMPORTANT NOTE: Damage to welds or frames resulting from over tightened bolts or improper assembly is not
covered under our warranty. Please read all instructions carefully before assembly. If you have any questions regarding
your assembly, call our Customer Service Center at 1-800-416-3511.
PARTS LIST ORDER PART #DESCRIPTION
BOLT COVER
HEX BOLT DRIVER
1/4" X 18 MM BOLT
OTTOMAN TOP
QTY
1
12
1
1
12
12
2
A
B
C
D
E
F
G
HHW0105
HW0004
HW0035
HW0006
FOOT CAP
FACTORY ASSEMBLY
*NOTE:PARTSSHOWNONPARTSLISTARENOTTOSCALE
6.5 X 1.0 MM
WASHER
Ø
FC0030
OTTOMAN LEG-1 2
F
H
G
D
Figure 3
F
H
G
Figure 2
C
H
F
G
A
B
F
H
G
FOOT CAP
Figure 1
OTTOMAN LEG-2
OTTOMAN LEG-3