Hanover TRADDN7PCBR-RED User manual


HanoverOutdoorFurniture




IMPORTANT
Ifyouhaveanyproblemswiththisproduct(missingordamagedparts,assemblyissues,etc.),
PLEASEDONOTRETURNTOTHERETAILER/STORE
fromwhereyoupurchasedtheproduct.
PleasecallourToll‐FreeCustomerServiceHotlineat:1‐800‐416‐3511
Between9:00AMand5:00PMEasternTime,MondaythroughFriday
Orvisitourwebsiteat:www.hanover‐products.com


Toexpediteanyfuturewarrantyclaims,pleaseretaintheInstructionSheet,Warranty
Cardandreceiptforfutureuse.
For additionalon‐linesupportonassembly,troubleshootingandcare&maintenanceofyouroutdoor
furniture,pleasevisitourwebsiteat:www.hanover‐products.com.
6/1/2015(a)

Page 4
ASSEMBLY INSTRUCTIONS
1
FOOT CAP
SWIVEL PLATE
"U" BAR
C
G
I
D
E
H
F
A
B
Position the swivel base on a flat, solid surface. Make sure the swivel plate is positioned all the way into
the base. It may have vibrated out during shipment. The two sets of holes in the swivel plate should be
facing away from you.
Note the arrows on both the swivel plate and the "U" bar portion of the chair frame. Position the chair frame
ontotheswivelplatesothatthetwopairsofholesinthe"U"barareexactlyalignedwiththetwopairsof
holes in the swivel plate and the arrows on both the "U" bar and swivel plate are pointing in the same
direction. Proper positioning of the chair frame on the swivel plate/swivel base assembly, and proper
alignment of the holes in the "U" bar with the holes in the swivel plate are critical to the safe, well balanced
swiveling motion of the chair.
Carefully examine the diagram. Attach a metal plate to two (2) bolts and guide the bolts through the top of
one set of holes in the "U" bar (located at the bottom of the chair frame) and into the pair of holes in the
swivel plate. From beneath the swivel plate, add a washer, then a spring washer and a nut to the end each bolt.
Hand tighten 3-4 revolutions only. Repeat procedure for pair of holes on the opposite side. Again, hand
tighten nuts 3-4 revolutions only. Do not tighten nuts completely.
Using the hex wrenches provided, tighten the nuts and bolts. Be sure the bolts are fully tightened. Remove
arrow labels from the “U” bar and swivel plate. Cover bolts and nuts with covers. Your chair is now ready
for use.
2
3

Page 5
*NOTE:PARTSSHOWNONPARTSLISTARENOTTOSCALE
PARTS IDENTIFICATION LIST
AAL08011
SWIVEL
ASSEMBLY
& BASE
FC0030
FOOTREST COVER
FACTORY ASSEMBLY G0304
FOOT CAP
FACTORY ASSEMBLY
HEX WRENCH-1 HW0008 1
HEX WRENCH-2 HW0007 1
BOLT COVER HW0028 4
QTY
5/16" X 43 MM
BOLT
Ø8.0 X 2.3 MM
SPRING WASHER HW0003
5/16" NUT HW0015
METAL PLATE
CHAIR FRAME
PARTS LIST DESCRIPTION ORDER PART #
2
4
4
4
1
1
HW0450
A
B
C
D
E
F
G
H
I
J
K
HW0686
4
Ø85X15MM
WASHER
.. HW0005
4
HW0109
AB1267
AB1268
NUT COVER

Page 4
ASSEMBLY INSTRUCTIONS
1
2
Attach a leg to the leg connector bracket by carefully guiding the bolts already in place on the table legs (each
leg has two bolts) through the holes in the leg connector bracket. Add a washer and a nut to the end of each bolt
as shown in . Repeat on the other three legs..Fig 2 Hand tighten only 2-3 turns.
Place the table top upside down on a flat, non-abrasive surface. Attach a table leg to the table top by using
the bolts and washers as shown in . Guide the bolts through the holes in the table leg, into the pre-drilled
holes in the table top. Repeat for the other three legs.
.Fig 1
Hand tighten only 2-3 turns.
3After making any necessary adjustments to the alignment of the table, use the hex bolt driver and hex wrench to tighten
all bolts . each bolt must be tightened a few revolutions at a time. In order to apply equal pressure to all bolt
joints, we recommend working in a cross corner (X fashion). Repeat until all bolts are tight.
Over tightening may strip bolts. Cover all bolts with covers.
Note:
Do not over tighten.
E
F
H
FOOT CAP
C
B
A
G
D
F

Page 5
*NOTE:PARTSSHOWNONPARTSLISTARENOTTOSCALE
PARTS IDENTIFICATION LIST
AMV02815
PARTS LIST DESCRIPTION ORDER PART #
BOLT COVER
HEX BOLT DRIVER
HEX WRENCH
1/4" NUT
TABLE LEG
LEG CONNECTOR
BRACKET
TABLE TOP
QTY
8
1
1
16
8
4
8
1
1
HW0105
HW0006
HW0009
HW0004
HW0014
FOOT CAP
FACTORY ASSEMBLY
A
B
C
D
E
F
G
H
I
J
Ø6.5 X 1.0 MM
WASHER
1/4" X 18 MM BOLT
HW0035
FC0030
UMBRELLA POLE
STOPPER & NUT
FACTORY ASSEMBLY
G0091
& HW0448
NUT COVER 8
HW0027
AT72764
AT72765
AT72766
UMBRELLA HOLE
RING (SET)
FACTORY ASSEMBLY
6 & G0235G023