Hanover BGC08006 User manual


HanoverOutdoorFurniture




IMPORTANT
Ifyouhaveanyproblemswiththisproduct(missingordamagedparts,assemblyissues,etc.),
PLEASEDONOTRETURNTOTHERETAILER/STORE
fromwhereyoupurchasedtheproduct.
PleasecallourToll‐FreeCustomerServiceHotlineat:1‐800‐416‐3511
Between9:00AMand5:00PMEasternTime,MondaythroughFriday
Orvisitourwebsiteat:www.hanover‐products.com


Toexpediteanyfuturewarrantyclaims,pleaseretaintheInstructionSheet,Warranty
Cardandreceiptforfutureuse.
For additionalon‐linesupportonassembly,troubleshootingandcare&maintenanceofyouroutdoor
furniture,pleasevisitourwebsiteat:www.hanover‐products.com.
6/1/2015(a)

IMPORTANT!! PLEASE READ ENTIRE INSTRUCTION SHEET BEFORE ASSEMBLY!!
TO EXPEDITE ANY FUTURE WARRANTY CLAIMS, PLEASE KEEP INSTRUCTION SHEET, WARRANTY CARD AND RECEIPT
Step 1: Carefully unpack and identify all parts packed in the carton against the parts list. Remove all protective materials. If you are missing any parts or are unsure how to
proceed with assembly, call our customer service center immediately at 1-800-416-3511. Do not attempt to assemble glider if any parts are missing or damaged.
Assemble furniture on a smooth, non-abrasive surface.
Step 2: by using two 5/16"x40 mm bolts and washers as shown in Fig.1. Guide the bolts through holes in back frame, into
pre-drilled holes in the . Hand tighten only. and back frame by using four 5/16"x25 mm bolts and
washers as shown in Fig.2. Hand tighten only. A and seat frame by using two 5/16"x25 mm bolts and two 1/4"x40 mm bolts
and four washers as shown in Fig.3. Hand tighten only.
Attach the back frame to right arm
right arm Attach the seat frame to right arm
ttach the left arm to back

Step 3: Attach the support frame assembly to one side of glider base/glider. Insert two bolts exactly as shown in Fig.4: throughØ15x4mm washers/armrest
frame/Ø15x6mm washers/glider bracket/Ø6.5x1.0mm washers/nuts. Hand tighten only as some adjustments may be needed for proper alignment or
tension of the glider. Repeat on opposite side.
B
D
AC
F
E
J
H
I
J
H
I
J
G
I
J
G
I
PN
M
LK
O
J
H
I
J
H
I
J
G
I
Fig.1 Fig.2 Fig.3
GLIDER BASE W/
GLIDER BRACKET
Fig.4

Step 4: by using four 1/4"x4 mm bolts and washers as
shown in Fig.5. Guide the bolts through holes in base, into the pre-drilled holes in the seat.
Hand tighten only.
Step 5: Using the hex wrench and hex bolt driver provided, tighten all nuts and bolts. Do not over
tighten bolts. If nuts and bolts are too tight or too loose, the glider will not function
properly. Test the operation of glider. Gliding motion should be smooth. Adjust tension
on the glider brackets, nuts and bolts as needed. Cover nuts and bolts with covers provided.
Step 6: With the help of another person, turn the chair in the upright position. Your chair is now
ready for use. If you have any questions, please call our Customer Service Center
at 1-800-416-3511.
Attach the complete base to the complete seat 5
IMPORTANT NOTE: Damage to welds or frames resulting from over tightened bolts or
improper assembly is not covered under our warranty. Please read all instructions carefully
before assembly. If you have any questions regarding your assembly, call our Customer Service
Center at 1-800-416-3511.
BGS12023
G0080
PARTS LIST
NUT COVER HW0027
HW0695
BOLT COVER-2HW0105
HEX BOLT DRIVER HW0006
HEX WRENCH HW0009
1/4" NUT HW0014
SEAT FRAME
4
4
4
1
1
1
1
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
Q
R
4
4
4
HW0004
HW0138
1/4" X 45 MM BOLT HW0040
DESCRIPTION ORDER PART # QTY
GLIDER BRACKET
FACTORY ASSEMBLY
ST4.8 X 25 BOLT
FACTORY ASSEMBLY
FOOT CAP
FACTORY ASSEMBLY FC0013
Ø6.5 X 1.0 MM WASHER
Ø6.5 X 6 MM WASHER

6
5/16" X 25 MM BOLT HW0186
8
5/16" X 40 MM BOLT HW0275
HW0005Ø8.5 X 1.5 MM WASHER
BOLT COVER-1HW0105 14
* NOTE: PARTS SHOWN BELOW ARE NOT TO SCALE
BACK FRAME 1
LEFT ARM 1
RIGHT ARM 1
GLIDER BASE W/
GLIDER BRACKET 1
SUPPORT FRAME
14
J
H
I
SG0154
SG0155
SG0156
SG0157
SG0158
SG0159
Fig.5

BGC08006
Step 1: Identify all parts packed in the carton against the parts list. Remove all protective materials. If any parts are missing or damaged, call our Customer Service Center at 1-800-416-3511. Do not attempt assembly
any parts are missing or damaged.
Step 2:
Step 3: Attach love seat arm by inserting two mm bolts with washers through the holes in front seat portion of the love seat frame and into the holes in the love seat arm shown in Figure 2. Attach back of love
seat arm by inserting two mm bolts with washers through holes in the back portion of love seat frame and into the holes in the rear portion of the love seat arm as shown in Figure 2. Hand tighten only.
Repeat for the opposite side.
Step 4: Tighten all bolts using the hex bolt driver provided. Tighten each bolt a few revolutions at a time, alternating between bolt connections until all bolts are tight. Do not over tighten. Over tightening may strip
bolts or damage the welds or frame. Cover all bolts with bolt covers provided.
Step 5: Your love seat is now ready for use. If you have any questions, please call our Customer Service Center at1-800-416-3511.
IMPORTANT NOTE: Damage to welds or frames resulting from over tightened bolts or improper assembly is not covered under our warranty. Please read all instructions carefully before assembly. If you
have any questions regarding your assembly, call our Customer Service Center at 1-800-416-3511.
Attach the seat frame to the back frame by using four 5/16"x40 mm bolts and washer as shown in Figure 1. Guide these bolts through the holes in the seat frame, into the fixed nuts already in place in the back
frame. Do not over tighten.
5/16"x25
5/16"x40
IMPORTANT. PLEASE READ ENTIRE INSTRUCTION SHEET BEFORE ASSEMBLY.
TO EXPEDITE ANY FUTURE WARRANTY CLAIMS, PLEASE KEEP INSTRUCTION SHEET, WARRANTY CARD AND RECEIPT
Figure 2
C
* NOTE: PARTS SHOWN ON PARTS LIST ARE NOT TO SCALE

D
FH
G
EH
G
Figure 1
A
B
H
F
G
FOOT CAP-1
FH
G
EH
G
8
5/16" X 40 MM BOLT
Ø8.5 X 1.5 MM
WASHER
LEFT ARM
RIGHT ARM
BOLT COVER
HEX BOLT DRIVER
FOOT CAP-1
FACTORY ASSEMBLY
HW0005
HW0022
HW0006
FC0030
1
12
HW0275
12
4
5/16" X 25 MM BOLT HW0186
1
1
1
1
BACK FRAME
SEAT FRAME
PARTS LIST DESCRIPTION ORDER PART # QTY
A
B
C
D
E
F
G
H
I
FOOT CAP-2
FACTORY ASSEMBLY FC0308
SK0939
SK0940
SK0941
SK0942

Step 4: After making any necessary adjustments to the
alignment of the table legs and the leg connector
bracket, use hex bolt driver to tighten all bolts.
Note: Each bolt must be tightened a few revolutions
at a time. In order to apply equal pressure to all bolt
joints, we recommend working in a cross corner
(X fashion). Repeat until all bolts are tight. Do not
over tighten. Over tightening may strip bolts or
damage the welds or frame. Cover all bolts with
covers.
Step 5: With the help of another person, turn the table in the
upright position. Note the clear bumpers spaced
evenly throughout the inside of the rim. Carefully
place glass inside the rim, resting on the clear
bumpers. Your table is now ready for use. If you
have any questions, please call our Customer Service
Center at 1-800-416-3511.
IMPORTANT NOTE: Damage to welds or frames
resulting from over tightened bolts or improper
assembly is not covered under our warranty. Please
read all instructions carefully before assembly. If you
have any questions regarding your assembly, call our
Customer Service Center at 1-800-416-3511.
IMPORTANT!! PLEASE READ ENTIRE INSTRUCTION SHEET BEFORE ASSEMBLY!!
TO EXPEDITE WARRANTY CLAIMS PLEASE KEEP INSTRUCTION SHEET, WARRANTY CARD AND COPY OF RECEIPT
PARTS LIST ORDER PART #DESCRIPTION
BOLT COVER
Ø6.5 X 1.0 MM
WASHER
HEX BOLT DRIVER
1/4" X 25 MM BOLT
1/4" X 35 MM BOLT
TABLE LEG
LEG CONNECTOR
BRACKET
TABLE RIM
GLASS TOP
QTY
1
12
1
1
1
12
4
8
4
A
B
C
D
E
F
G
H
I
BUMPER
FACTORY ASSEMBLY G0002
HW0105
HW0004
HW0037
HW0142
HW0006

FOOT CAP
FC0069
FOOT CAP
FACTORY ASSEMBLY
Step 1: Carefully remove glass and set aside until Step 5.
Lay glass flat--do not stand glass on edge. Remove
all protective materials and set parts on a flat, non-
abrasive surface. Identify parts packed in carton
against the parts list. If you are missing any parts or
are unsure how to proceed with assembly, call our
Customer Service Center at 1-800-416-3511. Do
not attempt assembly if any parts are missing or
damaged.
Step 2: Place the table rim (without glass) upside down on a
flat, non-abrasive surface. Attach the table leg to the
rim by using a 1/4"x25 mm bolt and a washer as shown
in Figure1. Guide the bolt through the hole in the table
leg, into the pre-drilled hole in the table rim. Do not
tighten completely. Some adjustments may be necessary
to ensure proper alignment of the table legs. Repeat for
the other three table legs.
Step 3: Attach the leg connector bracket to the legs by using the
1/4"x35 mm bolts as shown in Figure 2. Add a washer
to each bolt. Guide these bolts through the holes in the
leg connector bracket, into the fixed nuts already in
place in the legs. Do not over tighten.
Figure1
Figure2
* NOTE: PARTS SHOWN ON PARTS LIST ARE NOT TO SCALE
I
H
G
F
H
I
BKS04310
ST1601
ST1602
ST1603