Hanover MONACO5PC User manual


HanoverOutdoorFurniture




IMPORTANT
Ifyouhaveanyproblemswiththisproduct(missingordamagedparts,assemblyissues,etc.),
PLEASEDONOTRETURNTOTHERETAILER/STORE
fromwhereyoupurchasedtheproduct.
PleasecallourToll‐FreeCustomerServiceHotlineat:1‐800‐416‐3511
Between9:00AMand5:00PMEasternTime,MondaythroughFriday
Orvisitourwebsiteat:www.hanover‐products.com


Toexpediteanyfuturewarrantyclaims,pleaseretaintheInstructionSheet,Warranty
Cardandreceiptforfutureuse.
For additionalon‐linesupportonassembly,troubleshootingandcare&maintenanceofyouroutdoor
furniture,pleasevisitourwebsiteat:www.hanover‐products.com.
6/1/2015(a)

ADS17500
IMPORTANT!! PLEASE READ ENTIRE INSTRUCTION SHEET BEFORE ASSEMBLY!!
TO EXPEDITE ANY FUTURE WARRANTY CLAIMS, PLEASE KEEP INSTRUCTION SHEET, WARRANTY CARD AND RECEIPT
FRONT SEAT
SUPPORT BAR
Fig.1
B
C
F
Fig.3
D
E
FOOT CAPFOOT CAP
PARTS LIST PARTS LISTDESCRIPTION DESCRIPTIONORDER PART # ORDER PART #
SEAT FRAME BOLT COVER HW0022
FC0030
FOOT CAP
FACTORY ASSEMBLY
SEAT BASE
1/4" X 35 MM
BOLT
1/4" X 45 MM
BOLT
Ø6.5 X 1.0 MM
WASHER
HW0142
HW0040
HW0004
QTY QTY
1
A
B
C
D
E
F
G1
2
2
2
2
1HW0252
Fig.2
IMPORTANT NOTE: Your sling seat may appear to be slightly warped. This is not unusual.
Proper assembly procedure will straighten out the sling seat in the frame. There are four bolts
used to attach the seat frame to the seat base. After inserting all the bolts, each of these bolts
must be tightened a few revolutions at a time in rotation.
Step 1: Identify all parts packed in the carton against the parts list. Remove all protective
materials. Set parts on a flat, non-abrasive surface to avoid scratching. If you are missing
any parts or are unsure how to proceed with assembly, call our Customer Service Center
immediately at 1-800-416-3511. Do not attempt to assemble chair if any parts are
missing or damaged.
IMPORTANT NOTE: Assembling this chair requires attaching the sling seat frame to the seat
base. We recommend two people work together to assemble the chair since it is critical that all
the holes in the seat frame are aligned exactly with the holes in the seat base. All bolts need to
be inserted and tightened into the fixed nuts in a straight and direct path. Inserting the bolts at
even the slightest angle could strip the nuts and bolts, damaging the entire chair.
Step 2: Working from behind the chair, have another person stand in front of the chair and position
the sling seat frame in between the arms of the seat base as shown in Fig.1 so that the holes
on both sides of the upper portion of the seat frame back align with the fixed nut holes in
the seat base.
Step 3: Working from the front of the chair, add a washer to a 1/4"x45 mm bolt. From the
underside of the front seat support bar, insert the bolt with washer through one of the holes
in the seat support bar, into the fixed nut inside the lower front portion of the seat base as
shown in Fig.2. Hand tighten 3-4 revolutions only. Do not tighten Completely. Repeat
for opposite side of chair.
Step 4: From behind the chair, insert a 1/4"x35 mm bolt through the back arm portion of the seat
base and into the fixed nut in the seat frame as shown in Fig.3. Make sure the bolt is
inserted exactly straight! Hand tighten 3-4 revolution only. Do not tighten completely.
Repeat for opposite side of chair.
Step 5: Tighten all bolts with the hex bolt driver. Each bolt must be tightened a 3-4 revolutions
only at a time. Begin with top left bolt. Move to bottom right bolt then to top right bolt,
followed by bottom left bolt. Repeat this "X" pattern until all bolts are tight. Do not over
tighten bolts. Over tightening may strip bolts or nuts, damaging the entire chair. Cover
1/4"x35 mm bolts with bolt covers.
Step 6: Examine the chair from the front. If the sling seat does not appear tight or straight in the
seat base, repeat steps 3, 4 and 5. If you do not feel your chair is assembled properly, or
you have any questions, call our Customer Service Center at 1-800-416-3511.
IMPORTANT NOTE: Damage to welds or frames resulting from over tightened bolts or
improper assembly is not covered under our warranty. Please read all instructions carefully
before assembly. If you have any questions regarding your assembly, call our Customer
Service Center at 1-800-416-3511.
* NOTE: PARTS SHOWN ON PARTS LIST ARE NOT TO SCALE
HEX BOLT DRIVER
A
SLING TUBE CAP
FACTORY ASSEMBLY FC0358
AN0523
AN0524

FOOT CAP
IMPORTANT!! PLEASE READ ENTIRE INSTRUCTION SHEET BEFORE ASSEMBLY!!
TO EXPEDITE ANY FUTURE WARRANTY CLAIMS, PLEASE KEEP INSTRUCTION SHEET, WARRANTY CARD AND RECEIPT
Step 1: Remove all protective materials and set parts on a flat,
non-abrasive surface. Identify parts packed in carton
against the parts list. If you are missing any parts or are
unsure how to proceed with assembly, call our Customer
Service Center at 1-800-416-3511. Do not attempt
assembly if any parts are missing or damaged.
1/4"x30 mm
Step 2: Attach bottom base to the middle base by using four
bolts and washers as shown in Fig.1.
Guide the bolt through the holes in bottom base and
into the pre-drilled holes in the middle base. Do not
over tighten. With the help of another person, turn
the table base assembly in the upright position.
D
Fig.1
Fig.2
E
G
C
Step : With the help of another person, carefully please
the table top onto top base 1/4"x45 mm
4
, using four
bolts and washers as shown in Fig.3. Guide bolts
through the holes in top base and into the pre-drilled
holes in the table top. Do not over tighten .
Fig.3
Step 5: After making any necessary adjustments to the alignment of
the table top and top base, use the hex bolt driver to tighten
all bolts. Note: each bolt must be tightened a few
revolutions at a time. In order to apply equal pressure to
all bolt joints, we recommend working in a cross corner
(X fashion). Repeat until all bolts are tight. Do not over
tighten. Over tightening may strip bolts.
Your table is now ready for use. If you have any questions,
please call our Customer Service Center at 1-800-416-3511.
Step 6:
IMPORTANT NOTE: Damage to welds or frames resulting
from over tightened bolts or improper assembly is not covered
under our warranty. Please read all instructions carefully before
assembly. If you have any questions regarding your assembly,
call our Customer Service Center at 1-800-416-3511.
E
GB
A
G
F
Step 3:
1/4"x30 mm
Attach top base to the middle base by using four
bolts and washers as shown in Fig.2.
Guide the bolt through the holes in top base and
into the pre-drilled holes in the middle base. Do
not over tighten .
* NOTE: PARTS SHOWN ON PARTS LIST ARE NOT TO SCALE
DLQ01317
PARTS LIST DESCRIPTION ORDER PART #
HEX BOLT DRIVER
1/4" X 30MM BOLT
TABLE TOP
QTY
1
12
8
1
1
SE00F4653
HW0712
HW0038
A
B
C
D
E
F
G
H
I
J
K
Ø6.5 X 1.5 MM
WASHER
1/4" X 20 MM BOLT 4
HW0036
BOTTOM BASE
MIDDLEOM BASE
TOP BASE
1
1
FOOT CAP FC0404
G0157
4
PLASTIC UMBRELLA
HOLE RING
FACTORY ASSEMBLY
UMBRELLA POLE
STOPPER(SET)1
1
G0226

UMBRELLA USAGE
If you’re using an umbrella, remove the umbrella cover from the tabletop as shown in Fig. Guide
the umbrella pole through the umbrella hole ring into the umbrella pole stopper Use a screwdriver
driver (not included) to tighten the bolt in the umbrella pole stopper as shown in Fig. 6. Do not over tighten.
At this time, you can insert the umbrella pole into the hole of the table top as shown in Fig. 7.
5.
(L).
J
Fig. 5 Fig. 6
Fig. 7
K