Hanover Brigantine Dining Table User manual

Hanover Outdoor Furniture
6/1/2015 (b)
To expedite any future warranty claims, please retain the Instruction Sheet, Warranty
Card and receipt for future use.
Care and Maintenance
Store furniture in an upright position. Be careful to never allow water to build up in frames as this will
cause corrosion and freeze damage in cold climates. Wash all frames with a solution of mild soap and
water. Rinse with clean water and dry with a soft absorbent cloth towel. Frames can be treated with a
liquid wax for maximum protection against UV rays and/or salty, damp air. If your set includes
cushions, slings, and/or an umbrella they may be cleaned by hand with a solution of soap and water
with a clean water rinse. (Never machine wash cushions, slings or umbrella covers as this will result in
shrinkage or damage). After cleaning cushions tip on end and allow to drip dry. (Never use a
commercial or home dryer to tumble dry fabric goods). Do not use bleach or solvents to clean any
product! This will void the warranty.
For additional on‐line support on assembly, troubleshooting and care & maintenance of your outdoor
furniture, please visit our website at: www.hanover‐products.com.
IMPORTANT
If you have any problems with this product (missing or damaged parts, assembly issues, etc.),
PLEASE DO NOT RETURN TO THE RETAILER/STORE
from where you purchased the product.
Please call our Toll‐Free Customer Service Hotline at: 1-877-397-5144
Between 9:00 AM and 5:00 PM Eastern Time, Monday through Friday
Or visit our website at: www.hanover‐products.com

1-877-397-5144
Page 1 of 6
Briganne Glass Dining Table

Page 5 of 6
PART# DESCRIPTION PICTURE Q’TY
A Table Top 1
BTable Leg 4
C Support Tube 4
E
F
Bolt M6x20
Bolt M6x30
G
H
Washer
Bolt Cover
Open Wrench
4
12
16
16
1
1
DGlass
I

Page 6 of 6
Figure 1
Figure 2
Figure 3
BG
G
E
F
H
H
A
B
A
C
G
F
H
Step 2. Assemble the table legs (B) to the table top (A) with bolts (E&F) and washer (G) as shown in figure 1.
Assembly Steps:
Note: Do not fully tighten bolts until assembly is completed and alignment is correct.
Step 1. Carefully place the table top (A) upside down on a non-abrasive surface.
Step 3. Loosely attach the support bar (C) to the table leg (B) and table top (A) with bolts (F) and washer (G)
as shown in figure 2.
Step 4. Check the alignment and adjust if necessary. Once the alignment is correct, tighten all bolts with
open wrench ( I ) . Cover all bolts with bolt caps(H).
Step 5. Verify all bolts are securely tightened before use and turn your table right side up.
Place the glass (D) onto the table. Your table is now ready to use.(Figure 3).

1-877-397-5144
Page 1 of 7
Briganne Round Umbrella

Page 5 of 7
PART# DESCRIPTION PICTURE Q’TY
A 1
Support tube
Umbrella w/crank handleB 1

Page 6 of 7
Notice:
Table and umbrella base are only for constructional reference and sold separately.
Figure 1:
Step 1: Place the umbrella base under center of table.
Step 2: Loosen knob on umbrella base.
Step 3: Insert support tube (A) through hole in table and completely into umbrella base. See figure 1
Step 4: Tighten knob.
Figure 2
Step 5: Before opening the umbrella (B) turn it upside down and shake gently to separate ribs.
Step 6: Carefully insert umbrella (B) into support tube (A), until button rest on top of support tube. See figure 2.
Step 7: Align the button with the hole in support tube (A), press the button and lower umbrella until button snaps
through hole in support tube. See Figure 2
Step 8: Make sure button is locked in hole as shown in detail.

Figure 3
Step 9: slowly turn the handle of umbrella (B) until umbrella is completely open.
Warning : Never use umbrella without an umbrella base and matching table.
Always leave umbrella in down position when not in use.
Never use umbrella in high wind conditions. Damage to umbrella and or table can occur.
Page 7 of 7