Hanover Brigantine BRIGDN5PCSWSQ-SU User manual

HanoverOutdoorFurniture
IMPORTANT
Ifyouhaveanyproblemswiththisproduct(missingordamagedparts,assemblyissues,etc.),
PLEASEDONOTRETURNTOTHERETAILER/STORE
fromwhereyoupurchasedtheproduct.
PleasecallourToll‐FreeCustomerServiceHotlineat:1‐866‐851‐8438
Between9:00AMand5:00PMEasternTime,MondaythroughFriday
Orvisitourwebsiteat:www.hanover‐products.com
Toexpediteanyfuturewarrantyclaims,pleaseretaintheInstructionSheet,Warranty
Cardandreceiptforfutureuse.
For additionalon‐linesupportonassembly,troubleshootingandcare&maintenanceofyouroutdoor
furniture,pleasevisitourwebsiteat:www.hanover‐products.com.
6/1/2015(b)

Dining Table
Owner's Manual
Page 1of 7
If you have any problems with this product, DO NOT RETURN IT TO THE STORE
CALL OUR CUSTOMER SERVICE HOT-LINE AT
1-866-851-8438
Between 9 A.M. - 5 P.M. Eastern Time, Monday through Friday

Page 3 of 7

Page 4 of 7

PART# DESCRIPTION PICTURE QTY
A Table top 1
B Table leg 4
C Support Tube 8
AA Bolt M6 x18mm 16
BB Bolt M6 x 35mm 16
CC Washer 32
DD Bolt Cover 32
EE Wrench 1
PARTS LIST
Page 5 of 7

Assembly Steps:
Note: Do not fully tighten bolts until assembly is completed and alignment is correct.
Step 1. Carefully place the table top (A) upside down on a non-abrasive surface.
Step 2. Assemble the table legs (B) to the table top (A) with bolts (AA) and washer (CC)
as shown in figure 1.
Figure 1
Step 3. Loosely attach the support tube (C) to the table leg (B) and table top (A) with bolts (BB)
and washer (CC) as shown in figure 2.
Step 4. Check the alignment and adjust if necessary. Once the alignment is correct, tighten all
bolts with wrench (EE) . Cover all bolts with bolt caps(DD).
Figure 2
Page 6 of 7

Step 5. Verify all bolts are securely tightened before use and turn your table right side up.
Your table is now ready to use. (Figure 3).
Figure 3
Page 7 of 7

Page 1 of 6

Page 3 of 6

Page 4 of 6

Page 5 of 6

Page 6 of 6

1-866-851-8438
Page 1 of 7
Briganne Round Umbrella

Page 3 of 7
Manufacturer reserves the right to disclaim liability for any aspect of installaon
and any resulng inconvenience caused by a defecve part of a component.

Page 4 of 7

Page 5 of 7
PART# DESCRIPTION PICTURE Q’TY
A 1
Support tube
Umbrella w/crank handleB 1

Page 6 of 7
Notice:
Table and umbrella base are only for constructional reference and sold separately.
Figure 1:
Step 1: Place the umbrella base under center of table.
Step 2: Loosen knob on umbrella base.
Step 3: Insert support tube (A) through hole in table and completely into umbrella base. See figure 1
Step 4: Tighten knob.
Figure 2
Step 5: Before opening the umbrella (B) turn it upside down and shake gently to separate ribs.
Step 6: Carefully insert umbrella (B) into support tube (A), until button rest on top of support tube. See figure 2.
Step 7: Align the button with the hole in support tube (A), press the button and lower umbrella until button snaps
through hole in support tube. See Figure 2
Step 8: Make sure button is locked in hole as shown in detail.

Figure 3
Step 9: slowly turn the handle of umbrella (B) until umbrella is completely open.
Warning : Never use umbrella without an umbrella base and matching table.
Always leave umbrella in down position when not in use.
Never use umbrella in high wind conditions. Damage to umbrella and or table can occur.
Page 7 of 7