Hans Grohe Croma 280 Showerpipe 1jet EcoSmart 26789007 Manual

ZH 用户手册/组装说明 2
EN Instructions for use / assembly instructions 4
Lesezeichen
中文 2
English 4
Croma 280
Showerpipe 1jet EcoSmart
26789007

2
中文
安全技巧
装配时为避免挤压和切割受伤，必须戴上手
套。
本产品只允许作为洗浴、卫生和洁身之用。
头顶花洒夹持杆只为夹持头顶花洒而设计，不
得让其承载其它物品！
不得让儿童和肢体、精神和/或意识有障碍的
成人在不受监管的情况下使用淋浴系统。受酒
精或毒品影响的人员不得使用淋浴系统。
必须避免让身体敏感部位（如眼睛）接触到莲
蓬头喷水。必须保持莲蓬头与人头之间有足够
的距离。
该产品不得作扶柄使用。必须安装单独的扶
柄。
冷热水管间过大的压力差必须予以平衡。
安装提示
• 安装前必须检查产品是否受到运输损害。安装
后将不认可运输损害或表面损伤。
• 管道和阀门必须根据通用标准进行安装、冲洗
和检查。
• 请遵守当地国家现行的安装规定。
• 本安装说明中所规定的安装尺寸理想用于身高
1700mm左右的人士。尺寸可根据需要进行修
改。在这种情况下，您必须留意，如果安装高
度改变，则花洒到地板的最小高度也随之改
变，且必须考虑到连接尺寸的改变。
• 由有资格的专业人员进行产品安装时请注意：
在所有加固区域中，加固表面是否平整（无突
出的接缝或瓷砖），墙体结构是否适合产品安
装且未显露出任何缺点。
• 必须装上花洒所附带的滤网密封垫，以过滤管
道里的杂质污物。杂质污物会影响花洒的功能
和/或损坏花洒的功能部件，由此而产生的产品
损坏不属于汉斯格雅的保修范围。
• 本产品并非设计来与蒸气浴连接使用！
• 紧急情况下,可使用细的锯子将下方区域中阀门
与头顶莲蓬头之间的管子锯短。
• 如果连续流热水器导致任何问题，或者出现了
不同的水压，您必须在冷水端安装水流限制器
（单独订购，商品编号97510000）。
技术参数
工作压强： 最大1MPa
推荐工作压强： 0,1-0,5MPa
测试压强： 1,6MPa
 (1MPa=10bar=147PSI)
热水温度： 最大70°C
推荐热水温度： 65°C
中心距离： 150±12mm
连接管线G1/2: 左热右冷
热力消毒: 最大70°C/4分钟
• 自动防止回流
• 该产品专为饮用水设计！
符号说明
请勿使用含有乙酸的硅胶！
安全功能(参见第页11 )
恒温阀芯的安全功能可以预先设定所希望的最高
出水温度，例如最高温度为42℃
调节(参见第页10)
安装完成后必须检查调温器的出水温度。如在取
水处测量所得的温度与调温器上设定的温度有偏
差，那么必须进行调整。
保养(参见第页16)
• 单向阀必须在符合国家或当地的法律的情况下
按照DINEN1717定期检查（至少一年一次）
。
• 为了保证恒温器的稳定运转，请务必定期从最
热到最冷转动调温器。
大小(参见第页14)
流量示意图(参见第页15)
备用零件(参见第页23)
选装附件(不在供货范围内)
匹配瓷砖的圆盘镀铬#95239000
(参见第页23)
清洗(参见第页18)
操作(参见第页12)
请在使用喷头后略微倾斜，排空其中水分。

3
安装(参见第页6)
问题 原因 补救
龙头出水量小 - 水压不足 - 检查总水压
- 调压器过滤网脏污
(#96922000)
- 清洁龙头前面和恒温阀芯的过
滤网。(#96922000)
- 花洒过滤器元件有垃圾堵塞 - 清洗花洒和软管间的过滤网
串水，在龙头关闭的状态下，热
水被强迫流入冷水管路，或者相
反。
- 单向阀有垃圾堵塞或漏水 - 清洗单向阀，如有必要则更换
新的
龙头出水温度和温度设定的不符 - 恒温阀芯未被调节 - 调节恒温器
- 热水温度过低 - 将热水温度从42ºC升高到65ºC
水温无法调节 - 恒温阀芯表面结垢 - 更换-恒温阀芯
使用恒温龙头后，燃气热水器不
工作
- 过滤网有垃圾堵塞 - 清洗过滤网/更换过滤网
- 单向阀装反 - 正确安装单向阀
- 手持花洒的流量限制器没有去
除
- 去除流量限制器

4
English
Safety Notes
Gloves should be worn during installation to prevent
crushing and cutting injuries.
The product may only be used for bathing, hygienic
and body cleaning purposes.
The arm of the shower head is intended only to hold
the shower head. Do not load it down with other
objects!
Children as well as adults with physical, mental and/
or sensoric impairments must not use this product
without proper supervision. Persons under the
influence of alcohol or drugs are prohibited from
using this product.
Do not allow the streams of the shower touch
sensitive body parts (such as your eyes). An
adequate distance must be kept between the shower
and you.
The product may not be used as a holding handle. A
separate handle must be installed.
The hot and cold supplies must be of equal
pressures.
Installation Instructions
• Prior to installation, inspect the product for transport
damages. After it has been installed, no transport or
surface damage will be honoured.
• The pipes and the fixture must be installed, flushed
and tested as per the applicable standards.
• The plumbing codes applicable in the respective
countries must be observed.
• The installation dimensions stated in these installation
instructions are ideal for people of approximately
1700 mm in body height. The dimensions can be
altered if required. In this case, pay attention to the
fact that a change of installation height will also
change the minimum height, and that the altered
mounting dimensions must be taken into considera-
tion.
• During installation of the product by qualified trained
personnel, make sure that the entire fastening surface
is even and smooth (no protruding seams or tile
offset), that the finish of the wall is suitable to apply
the product and has no weak points.
• The mesh washer must be insert to protect the shower
against incoming dirt by pipework. Incoming dirt
leads to defects or/and can damage parts of the
shower; such caused faults voids all liability and
guarantee claims.
• The product is not designed to be used with steam
baths!
• If required, the bottom part of the pipe between the
fixture and the shower head can be shortened with a
fine-toothed saw.
• If the continuous water heater causes any problems,
or you have different water pressures you must install
a water limiter to the cold supply, (ordered
separately,article number 97510000).
Technical Data
Operating pressure: max. 1 MPa
Recommended operating pressure: 0,1 - 0,5 MPa
Test pressure: 1,6 MPa
(1 MPa = 10 bar = 147 PSI)
Hot water temperature: max. 70°C
Recommended hot water temp.: 65°C
Centre distance: 150±12 mm
Connections G 1/2: cold right - hot left
Thermal disinfection: max. 70°C / 4 min
• Safety against backflow
• The product is exclusively designed for drinking
water!
Symbol description
Do not use silicone containing acetic acid!
Safety Function (see page 11 )
The desired maximum temperature for example max.
42º C can be pre-set thanks to the safety function.
Adjustment (see page 10)
After the installation, the output temperature of the
thermostat must be checked. A correction is necessary if
the temperature measured at the output differs from the
temperature set on the thermostat.
Maintenance (see page 16)
• The check valves must be checked regularly
according to DIN EN 1717 in accordance with
national or regional regulations (at least once a
year).
• To guarantee the smooth running of the thermostat, it
is necessary from time to time to turn the thermostat
from total hot to total cold.
Dimensions (see page 14)
Flow diagram (see page 15)
Spare parts (see page 23)

5
Assembly (see page 6)
Special accessories (order as an extra)
tile-matching-disk Chrome Plated
#95239000 (see page 23)
Cleaning (see page 18)
Operation (see page 12)
To empty the overhead shower after use, hold it in a
slightly inclined position.
Fault Cause Remedy
Insufficient water - Supply pressure inadequate - Check water pressure (If a pump
has been installed check to see if
the pump is working).
- Regulator filter dirty (#96922000) - Clean filter in front of the mixer
and on the MTC-thermo cartridge
(#96922000)
- filter insert shower dirty - Clean filter seal between shower
and hose
Crossflow, hot water being forced
into cold water pipe, or vice versa,
when mixer is closed
- Backflow preventers dirty or
leaking
- Clean backflow preventers,
exchange if necessary
Spout temperature does not
correspond with temperature set
- Thermostat has not been adjusted - Adjust thermostat
- Hot water temperature too low - Increase hot water temperature to
42 ºC to 65 ºC
Temperature regulation not possible - thermo cartridge calcified - Exchange thermo cartridge
Instantaneous heater didn't work
with thermostat
- Filters are dirty - Clean the filter / exchange filter
- check valve hasn't moved back - Exchange check valves
- Flow limiter in handshower isn’t
removed
- Remove flow limiter

6
36 mm
1.
2.
X + 36 mm
X 36
X
1. 2.
Silicone
1 2
3a
SW 24 mm
3b
4 5
max.
39 mm
max.
5 mm
Montage

7
1.
2.
SW 30 mm
(17 Nm)
6 7
89
10
3.
2.
1.
11
1. 2.
Montage

8
2.
1.
60
1.
2.
13 14
15 16
Silicone
Ø 6 mm
17 18
12
Montage

9
94246000
SW 17 mm
(10 Nm)
SW 2 mm
(1 Nm)
SW 3 mm
(4 Nm)
1.
2.
19
21
20
22
Montage

10
SW 3 mm
1.
2.
1
3
2
1. 2.
SW 3 mm
(2 Nm)
Justierung