Hans Grohe Metris S 31063XX1 Installation guide

Installation Instructions / Warranty
Metris
31063XX1
Metris
31263XX1
Focus
31730001
Talis
32310XX1

2
Metris Widespread Lavatory Faucet 31063XX1
Metris Widespread Bidet Faucet 31263XX1
Talis S Widespread Lavatory Faucet 32310XX1
Focus Widespread Lavatory Faucet 31730XX1
31063XX1 31263XX1
Product Information
Requires 1/2" supply lines (not included)
Max. mounting surface thickness 1 1/8"
Hole sizes in mounting surface
Spout 1 3/8"
Valves 1 1/4"
Max. incoming water pressure 145 PSI
Recommended incoming water pressure 22 - 72 PSI
Max. incoming hot water temp. 176°F*
Recommended incoming hot water temp. 120° - 140°F*
Max. flow rate -- lavatory faucets 2.2 gpm
Max. flow rate -- bidet faucet 2.2 gpm
The bidet faucet is not suitable for use on vertical spray bidets.
This faucet may be used with a continuous flow water heater if the flow pressure is at least 20 PSI.
For best results, Hansgrohe recommends that this faucet be installed by a licensed, professional plumber.
*Please know and follow all applicable local codes when setting the temperature on the water heater.

3
31730XX1
32310XX1
Note:
To prevent shipping damage, the spout is attached to the
spout escutcheon with two adhesive strips. These strips
must be removed before the spout is installed.
Loosen the spout screw with a 2.5 mm Allen wrench.Pull
the spout away from the escutcheon.
Remove the adhesive strips.
Reassemble the spout assembly so that the hole for the
pull rod is at the rear of the spout.
adhesive strips

4
Installation
Remove the valve mounting nuts from the valves.
From below the mounting surface, push the valves up into
the holes. Install the mounting nuts on the valves.
Tighten the tensioning screws.
Place the handles over the valve mounting nuts. Tighten
the handles by rotating the escutcheons clockwise.
The handles should be parallel to the basin. If necessary,
loosen the tensioning screws and rotate
the valve slightly.
Install the spout. Rotate the spout escutcheon if necessary,
so that the hole for the pull rod is at the rear.
Tighten the mounting nut. Tighten the tensioning screws.

5
Slide the 3/8" compression nuts and ferrules over the
ends of the hoses.
Connect the hoses to the valve outlets. Use two wrenches
so that the hoses do not twist or become loosened from
the spout tee.
Screw the connecting hoses into the spout tee.
Install the supply lines (not included).
Install the drain.
Turn on the water and check all connections for leaks.

6
Install the pop-up drain
Remove the plunger assembly.
Unscrew the drain outlet flange from the tee.
Unscrew the tailpiece from the tee. Wrap
the threads with two layers of Teflon tape and
replace.
Install the white, flexible sealing gasket on the
flange. Place it in the sink outlet.
From under the sink, install the black mack
gasket, white friction ring and retainer nut to the
flange. Do not tighten the nut against the bottom
of the sink at this time.
Thread the tee and tailpiece to the flange. The
pivot must face the faucet. If necessary, turn
the drain assembly.
Tighten the retainer nut.
Place the plunger assembly in the drain.
Install the horizontal rod so that the end goes
through the loop in the bottom of the height
adjuster.
Install and hand tighten the pivot ball nut.
Attach the swivel connector to the end of the
horizontal rod.
Attach the swivel connector to the end of the
pull rod. Position as desired and tighten with a
small, flathead screwdriver.
plunger
flange
sealing gasket
mack gasket
friction ring
retainer nut
horizontal rod
height adjuster
pivot ball nut
swivel connector
pull rod
tee
tailpiece

7
User Instructions
Turn the right handle forward (clockwise) to turn
the cold water on. Turn the handle back (counter-
clockwise) to turn the cold water off.
Turn the left handle forward (counter-clockwise) to
turn the hot water on. Turn it back (clockwise) to
turn the hot water off.

8
Replacement Parts
1 handle - hot 97503XX0
handle - cold 97502XX0
2 valve set 97960001
3 hot cartridge 94009000
4 cold cartridge 94008000
5 connection hose 94071001
6 3/8" compression ftg 88513000
7 aerator 13085000
8 pull rod 96657XX0
9 spout mounting kit 13961000
10 spout 97504XX0
11 spout escutcheon 97505XX0
12 o-ring 11 x 2 98127000
13 bidet spout 97506XX0
14 aerator 97360XX0
15 ball joint 97362XX0
16 aerator 94010XX0
17 handle, hot 95337XX0
18 handle, cold 95338XX0
19 spout 95339XX0
XX = finish
00 = chrome
82 = brushed nickel
Metris
1
5
8
9
10
11
4
6
7
12
3
2
14
13
15

9
Talis Focus
7
12
22
12
8
9
11
5
6
3
4
5
6
3
8
11
4
16
17
18
19
9

10
Limited Lifetime Consumer Warranty
This product has been manufactured and tested to the highest quality standards by Hansgrohe, Inc. (“Hansgrohe"). This
warranty is limited to Hansgrohe products which are purchased by a consumer in the United States after March 1, 1996, and
installed in either the United States or Canada.
WHO IS COVERED BY THE WARRANTY
This warranty extends to the original consumer purchaser only. This warranty is non-transferable.
WHAT IS COVERED BY THE WARRANTY
This warranty covers only your Hansgrohe manufactured product. Hansgrohe warrants this product against defects in material
or workmanship as follows: Hansgrohe will repair at no charge for parts only or, at its option, replace any product or part of
the product that proves defective because of improper workmanship and/or material, under normal installation, use, service
and maintenance. If Hansgrohe is unable to provide a replacement and repair is not practical or cannot be timely made,
Hansgrohe may elect to refund the purchase price in exchange for the return of the product.
LENGTH OF WARRANTY
Replacement or repaired parts of products will be covered for the term of this warranty as stated in the following two sentenc-
es. If you are a consumer who purchased the product for use primarily for personal, family, or household purposes, this war-
ranty extends for as long as you own the product and the home in which the product is originally installed. If you purchased
Cleaning Recommendation for Hansgrohe Products
Modern lavatory faucets, kitchen faucets, and showers consist of very different materials to comply with the needs of the
market with regard to design and functionality. To avoid damage and returns, it is necessary to consider certain criteria when
cleaning.
Cleaning Materials for Faucets and Showers
Acids are a necessary ingredient of cleaning materials for removing lime, however please pay attention to the following points
when cleaning faucets and showers:
Only use cleaning materials which are explicitly intended for this type of application.
Never use cleaning materials which contain hydrochloric, formic, phosphoric, or acetic acid, as they cause considerable
damage.
Never mix one cleaning material with another.
Never use cleaning materials or appliances with an abrasive effect, such as unsuitable cleaning powders, sponge pads,
or micro fiber cloths.
Cleaning Instructions for Faucets and Showers
Please follow the cleaning material manufacturer’s instructions. In addition, pay attention to the following points:
Clean the faucets and showers as and when required
Use the amount of cleaning product and the amount of time recommended by the manufacturer. Do not leave the cleaner
on the fixture longer than necessary.
Regular cleaning can prevent calcification.
When using spray cleaners, spray first onto a soft cloth or sponge. Never spray directly onto the faucet as droplets can
enter openings and gaps and cause damage.
After cleaning, rinse thoroughly with clean water to remove any cleaner residue.
Important
Residues of liquid soaps, shampoos, and shower foams can also cause damage, so rinse with clean water after using.
Please note: if the surface is already damaged, the effect of cleaning materials will cause further damage.
Components with damaged surfaces must be replaced or injury could result.
Damage caused by improper treatment is not covered under the warranty.
•
•
•
•
•
•
•
•
•