Happy Beds Capri 2 Drawer Sleigh Bed User manual

Assembly Instructions
VERSION: 161109
CAPRI FABRIC BED WITH DRAWERS
135CM
01
Capri 2 Drawer Sleigh Bed
Assembly Instructions
www.happybeds.co.uk
Important before assembly:
Read these instructions carefully before assembling or using the product.
Please check the contents of the boxes before attempting to assemble this product. The instructions will
have a checklist of parts and fittings.
It would be sensible to lay a rug or a carpet on the floor where you intend to assemble the product,
to void scratches and damaging the product or the floor.
Assemble the product as close to its intended final location/room as possible.
Do NOT use any power tools as this may damage the frame.
Health & Safety:
This product or some parts of this product will be heavy. Please use an assistant when lifting.
DO NOT jump on the product or any of its parts.
DO NOT use this product if any parts are missing, damaged or worn.
DO NOT use this product unless all fixings are secured.
Please keep small parts out of reach of children.
Always use on a level, even surface.
Please keep these instructions for future reference.

@
This product or some parts of this product will be heavy. Please use an assistant
when lifting.
Never drag or push the pieces across a hard or stone floor as this will cause
damage to the joints. Use a carpet or a rug for extra care.
If you have problems assembling or have damaged or missing pieces, please
contact us by visiting:
https://www.happybeds.co.uk/customer-service
(Not metal)
These tools are not
necessary, but may
help to assemble
certain parts of the
product.
Do NOT use any power
tools as this may
damage the frame.

Hardware
M8 x 30mm Bolt
- 16 X
Already inserted into
Head & Foot Ends
1 2 3
Screw M5 x 50mm
- 12 X
Nut - 28 X
76 8 9
5
Allen Key (M5)
- 1 X
Screw M3 x 20mm
- 40 X Screw M4 x 30mm - 16 X
Parts
A
Headboard - 1 X
B C D
Footboard - 1 X Side Rail - 2 X Centre Rail - 1 X Centre Support Legs - 3 X
E
Screw M5 x 50mm
- 28 X
Support Legs - 4 X
F G H I J
K L
10
11
4
Adjustable Foot
- 4 X
Drawer Front Panel I
- 2 XSprung Slat - 32 X Drawer Side Panel - 4 X Drawer Front Panel II - 2 X
Drawer Bottom Panel
- 2 X Drawer Back Panel - 2 X Bottom Support Rail I - 4 X Bottom Support Rail II - 2 X Wheel x 10pcs - 10 X
M N O
P
Wooden Foot - 4 X
12
Slat Cap - 32 X
Middle Cap For
Sprung Base - 16 X
Bolt M8 X 45mm
+Flat Washer Bolt
- 8 X
03
Non-Slip Pads
- 7 X
13
Non-Slip Pads
40 x 75mm - 4 X
14
Screw M5 x 70mm
- 3 X

04

STEP 1
STEP 2
Please note that
the Bolt (1) x 16
are prefixed into
parts A & B
STEP 3
P
P
P
3
A
B
A & B
X12
X16
1
5
05
X4 A & B
P
E
E
E
D
E
D
14
E
X3 X3
2
13
13
2

STEP 4
Slot into bracket behind fabric
PULL
STEP 5
STEP 7
STEP 6
face out
face out
PUSH
12
12
G
G
11
X32
D
X 2
5
10
C
F
4
X 8
12
G
C
C
PUSH
PUSH
06
12 12
G
11 X16
ARROWS ON LABELS
POINT TO EACH OTHER
4
2
2
X 4
X16
11
G

Important:
Make sure when you fit the nuts
that the hole is in the correct
alignment.
STEP 11
STEP 8 Drawer Assembly.
FOLLOW LINE ON BACK OF
DRAWER FACE PANEL
STEP 10
STEP 9
III III
J
7
6
I
J
I
K
I
I
L
6
M
N
M
N
M
6
10
8
H
H
9
J
X40
07

08
www.happybeds.co.uk
General Care & Maintenance
Please dispose of all packaging safely.
Wipe clean with a slightly damp cloth.
Avoid the use of all household cleaners and abrasives.
Periodically check all screw & fixings to ensure they are secure.
When moving your product, carefully lift into place. Never drag or push the pieces across the
floor as this will cause damage to the joints and could result in failure to the product that will
invalidate the warranty.
For more information on cleaning and product care visit:
https://www.happybeds.co.uk/help-and-advice
We’ve tried to make this product as easy to assemble as possible. In the unlikely event that
you have problems putting it together or have damaged or missing pieces, please contact
us by visiting:
https://www.happybeds.co.uk/customer-service
Notes