Happy Beds Winchester User manual

Winchester 2 Drawer Bedside
Table
Assembly Instructions
www.happybeds.co.uk
Important before assembly:
Read these instructions carefully before assembling or using the product.
Please check the contents of the boxes before attempting to assemble this product. The instructions will
have a checklist of parts and fittings.
It would be sensible to lay a rug or a carpet on the floor where you intend to assemble the product,
to void scratches and damaging the product or the floor.
Assemble the product as close to its intended final location/room as possible.
Do NOT use any power tools as this may damage the frame.
Health & Safety:
This product or some parts of this product will be heavy. Please use an assistant when lifting.
DO NOT jump on the product or any of its parts.
DO NOT use this product if any parts are missing, damaged or worn.
DO NOT use this product unless all fixings are secured.
Please keep small parts out of reach of children.
Always use on a level, even surface.
Please keep these instructions for future reference.

@
This product or some parts of this product will be heavy. Please use an assistant
when lifting.
Never drag or push the pieces across a hard or stone floor as this will cause
damage to the joints. Use a carpet or a rug for extra care.
If you have problems assembling or have damaged or missing pieces, please
contact us by visiting:
https://www.happybeds.co.uk/customer-service
(Not metal)
These tools are not
necessary, but may
help to assemble
certain parts of the
product.
Do NOT use any power
tools as this may
damage the frame.

Vendor: S000401
Hardware List
Part Item Qty
A Wooden Dowel 16
BCam Bolt 21
CCam Lock 21
D Tack 20
E Slip Shoe 4
F14mm Screw 20
G Sticker 2
HHandle 2
I Side Slide 2
J Drawer Slide 2
K25mm Screw 1
L Trapeze Fixation 1
2X
012345 6 78 9 1 0 1 1 1 2 1 3 1 4 1 5 1 6
mm
Parts List
Part Item Qty
1 Right Side 1
2Left Side 1
3Baseboard 1
4 Top 1
5Left Column 1
6 Right Column 1
7 Upper Traverse 1
8Bottom Traverse 1
9 Traverse 1
10 Back 1
11 Drawer Front 2
12 Drawer Back 2
13 Drawer Side 4
14 Drawer Bottom 2
4
1
2
8
9
3
7
10
5
6
11
13
13
12
14

Vendor: S000401
1
9
A
A
2
B
B
B
B
B
4
B
B
5
6
Step 1: Insert the hardware (A) into the traverse (9), baseboard (3), upper traverse (7) and drawer
side (13).
Do NOT use any power tools are this may damage the frame and will invalidade any claim.
Step 2: Insert the hardware (B) into the right side (1), left side (2), top (4), bottom traverse (8) right
column (6), left column (5), drawer front (11) and drawer back (12). Then attach hardware (I) to
the right & left side (1 & 2) using hardware (F).
Do NOT use any power tools are this may damage the frame and will invalidade any claim.
A
A
13
4X
B
B
B
B
11
12
3
7
A
A
B
F
F
I
I
F
B
8
2X
2X

Vendor: S000401
C
5
Step 3: Assemble the right column (6) and left column (5) to the right side (1) and left side (2) using
hardware (C).
Do NOT use any power tools are this may damage the frame and will invalidade any claim.
6
C
12
Step 4: Assemble the bottom traverse (8) to the traverse (9) using hardware (C).
Do NOT use any power tools are this may damage the frame and will invalidade any claim.
8
9
C

Vendor: S000401
C
C
C
B
1
9
Step 5: Attach the upper traverse (7), the traverse (9) and the baseboard (3) to the right & left side
(1 & 2) using hardware (C) and (A).
Do NOT use any power tools are this may damage the frame and will invalidade any claim.
2
7
3
C
4
1
2
C
C
7
K
L
4
Step 6: Insert hardware (L) and (K) tothe upper traverse (7) as shown below. Fix the top (4)
using hardware (C). Then attach hardware (E) and (D) tothe bottom of the right side (1), left
side (2).
Do NOT use any power tools are this may damage the frame and will invalidade any claim.
D
E
1
2
7

Vendor: S000401
B
C
C
F
J
J
14
13
13
12
11
F
F
F
FH
C
Step 8: Attach the drawer side (13) tothe drawer back (12) using hardware (B) and (C) then insert
the drawer bottom (14).
Attach the drawer side (13) tothe drawer front (11) using hardware (B) and (C).
Attach hardware (J) to the drawer side (13) using hardware (F). Then attach hardware (H) to the
drawer front (11) using hardware (F).
Do NOT use any power tools are this may damage the frame and will invalidade any claim.
D
D
D
10
Step 7: Attach the back (10) to the back of the assembled product using hardware (D).
Do NOT use any power tools are this may damage the frame and will invalidade any claim.
2X
2X
2X

Vendor: S000401
Step 9: Insert the drawer as shown below.
Place hardware (G) over the holes shown below.
Do NOT use any power tools are this may damage the frame and will invalidade any claim.
Additional Information:
• For complete product information, images and dimension diagrams
please visit the website www.birlea.com
• If you have any issues with your item please contact the retailer
directly you purchased it from who will be able to resolve any
issues with Birlea.
• Why donʼt you send us photos of your assembled furniture to [email protected]
to be shared in our #birleahome feature on Instagram.
J
I
G
Inserting the Drawers

www.happybeds.co.uk
General Care & Maintenance
Please dispose of all packaging safely.
Wipe clean with a slightly damp cloth.
Avoid the use of all household cleaners and abrasives.
Periodically check all screw & fixings to ensure they are secure.
When moving your product, carefully lift into place. Never drag or push the pieces across the
floor as this will cause damage to the joints and could result in failure to the product that will
invalidate the warranty.
For more information on cleaning and product care visit:
https://www.happybeds.co.uk/help-and-advice
We’ve tried to make this product as easy to assemble as possible. In the unlikely event that
you have problems putting it together or have damaged or missing pieces, please contact
us by visiting:
https://www.happybeds.co.uk/customer-service
Notes