Hardlife Utility C2020H User manual

SHELTER
ASSEMBLY MANUAL
Model #C2020H / W6x L6x H 2m
Model #C2040H / W6x L12x H 2m
Container Shelter

Parts List
Spare Parts List for C2020H & C2040H
Part Code
Description
Qty For
C2020H
Qty For
C2040H
L1
Base plate on left
5
9
R1
Base plate on right
5
9
1
Three way fitting
2
2
2
Four way fitting
3
7
3
Top bent tube
10
18
4
Sidewall bent tube
10
18
5
Top roof purlin
4
8
6
Connection purlin
16
32
7
φ25mm Lower tensioning tube for roof cover
2 Groups
2 Groups
8
Angle seat for roof cover
4
4
9
Roof cover
1
1
10
φ25mm Plastic Plug
4
4
11
Ropes
1 Bundle
1 Bundle
13
Bolt M8x70
80
144
14
Butterfly bolt
8
16
14A
Rachet Straps
10
18
14B
1.5'' Rachet (With Screws)
10
18
16
Tube for connecting cover
4
4
17
Angle seat
6
6
18
Ratchet tie down
2
2
19
Iron plate
2
2
20
Bolt M10x30mm
6 sets
6 sets
21
Ropes
20 m
20m
22
End cover
1
1

SPECIFICATION
C2020H : Width: 6m Length: 6m Height: 2m
C2040H : Width: 6m Length: 12m Height: 2m
IMPORTANT-----READ MANUALFIRST
Improper site preparation, Assembly and Maintenance may invalidate warranty and
cause unnecessary and costly mistake. If you have any questions contact your local
dealer.
For User Friendly assembly we have identified each individual component with the
part code as indicated in the parts list. Please refer to the part code numbers and
drawing to ensure problem free assembly.
It’s necessary to tighten the roof fabric enough to avoid “hammocks” on the roof and
also re-tighten once or twice again after a few months of use. This is important when
assembly in cold weather (autumn and winter) because the fabric is stiff then and
when we got the sun and warm weather afterwards it will make the fabric “slack”
again and need to be re-tighten before next winter.
It’s the owners responsibility to take of snow immediately if not slide off by itself.
READALL INSTRUCTIONS BEFOREASSEMBLY
1. Keep work area clean. Cluttered areas invite injuries. Do not set up near snow
drifts, in slippery places, in high winds, or wet location.
2. Keep children away. All children should be kept away from the work area.
3. Don’t over reach. Keep proper footing and balance at all times.
4. Do not assemble in under the influence of alcohol or drugs. Read warning labels
on prescriptions to determine if your judgment or reflexes are impaired while
taking drugs. If there is any doubt, do not assemble.
5. Be aware of possible windy conditions; fasten the bases in concrete if these
conditions are likely to occur. Remove the cover during hurricane.
6. Be careful with power and heat sources. Do not keep heat sources near the
tarpaulin. Do not expose to open flame.
7. Be aware of personal safety during assembly and use. Be careful not to pinch
fingers with clips and tubes when assembling: when using makes sure there is
adequate ventilation for exhaust and other dangerous fumes.

A--EQUIPEMNTAND TOOLS FOR INSTALIATION
1. Measuring tape
2. String for alignment
3. Step ladder
4. Welder
5. Sledge hammer
6. Wrench
7. Scissors
INSTALLATION PROCESS
A—BASE INSTALLATION
Please refer to the diagram (Figure 1) to place the base plates.
Above is base plates lay out for C2020H

Above is base plates lay out for C2040H
Figure 1
1. The measure is from center to center of the tubes. Referring to the above diagram
and confirm the place of the base plates. ENSURE THAT THE FOUNDATIONS IS
SQUARE.
2.All the base plates need use welder to be welded on the Containers.

Above is Frame for C2020H
Below is Frame for C2040H

B--FRAME INSTALLATION
1. As Figure 2 shown find Three-way fitting (part code 1), Top bent tube (part code 3)
and Sidewall bent tubes (part code4). To connect them by Screw M8x70 （part
code13）.Which makes one group of arch. Please NOTE the direction of the screw.
DO NOT install the screws on the top of the truss where the fabric will rest.
2. Lift an assembled arch into one base plate and force the other end of the arch into
the opposite base plate.
3. When finishing installing the first two arches, connect the Connection purlin onto
them by using screw M8x70（part code 13）.There is 4 pieces of Connection purlins
(part code 6) and 1 piece of Top roof purlin (part code 5) between each arch. Then
install the third arch into base plate and connect the purlins. By turns the assembly for
the frame is finished.

Figure 2
C--INSTRUCTION FOR COVER ATTACHED
Install the Roof Cover
NOTE: DO NOT install the cover onto the frame of your building in high wind
conditions. A slight breeze is the most advantageous for cover installation. To take
advantage of the breeze, pull the cover up over the arches with the breeze blowing in
the cover like a sail filled with air.

Figure 3

1. Put the Roof cover (part code 9) EVENLY, CARRFULLR AND SLOWLY on the
frame. Adjust the cover so that it is square and evenly centered on the frame.
2. Weld the Angle seats (part code 8) on each container and use Rope (part code 11)
to knit the front & back ends of the cover to the end arches..
3. Cut pockets above the rachet(No.14B) according to the position of the base plates
and put the Lower Tension tubes for roof cover (part code 7) into the pocket of roof
cover. Then use the Rachet Straps (part code14A) to tie down the Lower tension tubes
like the Figure.
3. Finally install the∮25mm Plastic plug for base rail section (part code 10) into two
end of the Lower tension tubes.

Install the End Cover
Find out the spare parts according to above drawing, fix the end cover in the back of
the shelter.