Hardline TH-1 User manual

Please read the following notice carefully before using,
install and operate the meter correctly.
1.Please use the product accordance with the user guide strictly.
2.Please do not dismantle the product by yourself.
3.
4.When the product is in the intense vibration or strong impact. It will cause a failure
5.The product must be used within the specified range of voltage.
6.The backlight function will need more battery level, battery life is limited ,when the battery level is low, please replace
the battery as soon as possible.The battery item is CR2032.
Due to the waterproof design of the product, it can be used in the rain, but can not be put into in deep water.
1.How to install the battery.
Open the battery cover
Please use a coin to rotate the battery
Place the battery
Smooth side should be put upward.
Close the battery cover
Please use a coin to rotate the battery cover which
【Notice】:The original data will be retained after replace battery.
2.How to install the product.
tape on the back of the thermometer
Put the needle surface of magic
tape on the device
Put the end of the sensor into the products which to be tested.
3.Check the correctness of the product installation.
Access to the sensor,if temperature data is displayed , which means the product was installed correctly.
2.Set the temperature reminder value.
1.View the working data.
【Notice】:When the product is working without backlight, short or long press any button to make the product in the backlight.
123
4
1
2
Precautions
1
Installation
2
Connect the product wire and temperature
product application
3
1
cover which has “open” word, and
will open the battery cover
has “CLOSE” word, and will close the battery
cover
Put the rough surface of magic
23
1.
2.
temperature reminder value setting interface, the default value is "100 ℃".
In the temperature reminder value setting interface , long or short press SET button to add the setting value, long or short
press MENU button to reduce the setting value . The setting value range is from - 20 ℃ to + 300 ℃ (-4 ℉ - + 572 ℉).
In the temperature Reminder Value interface,long press the MENU button more than 2 seconds, then enter into the
sensor as below picture
When the product is in the state with backlight,short press the MENU button,you can view "over temperature reminded value,
the maximum tested temperature value,temperature unit,sensor type and instant temperature value" in turn.

?
or damage?
6.Battery level display.
Battery level is displayed as below：
When the battery voltage is empty, it will flash to remind you to change the battery.
Specification-----1 magic tape-----1 zip tie-----2 temperature sensor -----(two kinds Ring terminal end (NTC) )
PT100 temperature range
Temperature accuracy
Refresh rate
Canning material
Waterproof
Display mode
Display window size（ visible）
The temperature sensor line length
Product weight
Product size
Battery specificaion
-20 - +300℃(-4-+572℉)
±1% ℃(℉)
6s
ABS
IP65
22mm×44mm LCD
18mm*42mm
60cm
84g
67mm×35mm×17mm
CR2032 210mAH
Problems Possible reason Solution
The window screen no
display
2.The battery installation is wrong.
1.Is the battery empty .
2.Check if the battery installation is
1.Replace a new battery.
LCD screen display err 1.Sensor is not installed in the right way.
2.Sensor is damaged.
1.Reinstall the sensor
2.Change the new sensor
.
.
Display no change Disturbed crash. Install the batteries again.
LCD screen display is not
clear or discoloraton
1.Angle wrong.
2.Lack of battery.
1.Adjust angle
2.Replace battery
.
.
After setting, press the MENU button and SET button together more than 2 seconds, then confirm and exit the setting interface.
When the product is working ,if the instant temperature is higher than the temperature reminder value, the warning
3.Reset the maximum temperature.
In the maximum temperature interface,press the MENU button 2 seconds, the current max temperature value will
the reset value is - 20 ℃ (-4 ℉).
more than
be reset,
4.Set the temperature unit.
In view of the temperature unit interface, long press the MENU button 2 seconds,then enter into the
interface,the temperature unit symbol will flash.The default of temperature unit is "c".
more than
temperature unit setting
After entering the setting interface, short press the SET button or MENU button to select the temperature unit (℃ or ℉).
After setting, long press the MENU button and SET button together 2 seconds, then confirm and exit the settingmore than
【Notice】: After switching the temperature unit, the original temperature reminder value will have a small changes.
7.When the product is in any working condition, such as in setting interface or view if there is without any operation
switch to the instant temperature display interface automatically.
interface,
more than 10 seconds,it will
3
4
1
2
3
1
2
Product parts list
4
Product Technical Parameters
5
Troubleshooting
6
5.Sensor type selection.
In view of the sensor type interface,long press the MENU button more than 2 seconds,then enter into the sensor type selection
After entering the setting interface,short press the SET button or MENU button to select the sensor type(NTC or PT100).
1
2
3
NTC temperature range -20℃-+150℃(-4-+302 )℉
signs will flash in the instant temperature interface.
After setting,long press the MENU button and SET button together more than 2 seconds,then confirm and exit the setting
interface,the current sensor type is flashing.The default of the sensor type is NTC.
interface.
Radiator wedge
correct or not.
interface.