Harman Accentra Installation instructions

3-90-08326R25_06/13
SAFETY NOTICE
PLEASE READ THIS ENTIRE MANUAL BEFORE INSTALLATION AND USE OF THIS PELLET FUEL-BURNING ROOM
HEATER. FAILURE TO FOLLOW THESE INSTRUCTIONS COULD RESULT IN PROPERTY DAMAGE, BODILY INJURY,
OR EVEN DEATH.
FOR USE IN THE U.S. AND CANADA. SUITABLE FOR INSTALLATION IN MOBILE HOMES
IF THIS HARMAN® ACCENTRA PELLET STOVE IS NOT PROPERLY INSTALLED, A HOUSE FIRE MAY RESULT. FOR
YOUR SAFETY, FOLLOW INSTALLATION DIRECTIONS.
CONTACT LOCAL BUILDING OR FIRE OFFICIALS ABOUT RESTRICTIONS AND INSTALLATION INSPECTION
REQUIREMENTS IN YOUR AREA.
CONTACT YOUR LOCAL AUTHORITY (SUCH AS MUNICIPAL BUILDING DEPARTMENT, FIRE DEPARTMENT, FIRE
PREVENTION BUREAU, ETC.) TO DETERMINE THE NEED FOR A PERMIT.
CETTE GUIDE D'UTILISATION EST DISPONIBLE EN FRANCAIS. CHEZ VOTRE CONCESSIONNAIRE DE HARMAN®
HOME HEATING.
SAVE THESE INSTRUCTIONS.
Installation & Operating Manual
Model(s):
Accentra Freestanding Pellet Stove
NOTICE: SAVE THESE INSTRUCTIONS
Hot glass will cause burns.
• Donottouchglassuntilitiscooled
• NEVERallowchildrentotouchglass
• Keepchildrenaway
• CAREFULLYSUPERVISEchildreninsameroomas
stove.
• Alertchildrenandadultstohazardsofhightemperatures.
High temperatures may ignite clothing or other
ammable materials.
• Keepclothing,furniture,draperiesandotherammable
materialsaway.
HOT SURFACES!
Glassandothersurfacesarehotduring
operationandcooldown.
WARNING
!
To obtain a French translation of this manual, please
contactyourdealerorvisitwww.harmanstoves.com
Pourobtenirunetraductionfrançaisedecemanuel,s’il
vous plaît contacter votre revendeur ou visitez www.
harmanstoves.com
NOTE

3-90-08326R25_06/13
DANGER : Risque d’électrocution. Débrancher l’appareil avant toute intervention. Ne remplacer la vitre qu’avec une vitre céramique 5 mm de même qualité disponible auprès de votre revendeur. Tenir la porte frontale et le couvercle de trémie hermétiquement clos durant le fonctionnement de l’appareil.  Nominale: 10,5 KW Réduite: 1,8 KW Concentration CO (à 13 % O2) à puissance nominale: < 0,02 % à puissance réduite: < 0,04 %  à puissance nominale: 84 % à puissance réduite: 73% DISTANCES DE SECURITE PAR RAPPORT AUX MATERIAUX COMBUSTIBLES Entre Mur Arrière et appareil 6 cm Entre Paroi latérale et appareil 31 cm Installation en angle Entre murs et apparell 16 cm Installation en alcôve Hauter minimale de l’alcôve 153 cm Parois latérales de l’alcôve 38 cm Profondeur maximale de l’alcôve 60 cm Utiliser une protection de sol non combustible sous l’appereil qui s’étend sur les côtes, l’avant et l’arrière du poêle (voir schéma). Pour la distance à l’avant, mesurer à partir de la surface de la porte en verre. ll est recommendé que la protection s’étende jusque sous le conduit en cas d’installation d’un conduit horizontal ou sous le té en cas conduit vertical.

Room Heater Pellet Fuel Burning
Also for use In Mobile Homes.
This this pellet burning appliance has been tested and listed for use In
Manufactured Homes In accordance with OAR 814-23-900 through 814-23-909
MINIMUM CEARANCES TO COMBUSTIBLES Back Wall to Appliance 2.25” Side Wall to Appliance 12" Corner Installation Walls to Appliance 6.25” Use a non-combustible oor protector extending under and to the sides, front and back of the unitas shown in oor protection diagram. Measure front distance from the surface of the glass door.          Floor Protection* USA CANADA Sides (A) 6” 200mm Back (B) 0” 200mm Front* (C) 6” 450mm  Alcove Installation Min. Alcove Height 60” Min. Alcove Side Wall 14.75” Max. Alcove Depth 24”
Test to/testé à ASTM E 1509-04, ULC/ORD-C1482-M1990, ULC-S627-00 Tested by Emitech, Apave & BFP Electronique EN60335-1, EN55014-1, EN 61000-3-2, EN 14785:2005 Test date: February 2004 Room Heater Pellet fuel Burning type (UM) 84-HUD “PREVENT HOUSE FIRES” Install and Use only in accordance with manufacture’s installation and operation instructions. Contact local building or re ofcials about restrictions and inspection in your area.  Do not install appliance in a sleeping room. An outside combustion air inlet must be provided. The structural integrity of the manufactured home oor, ceiling and walls must be maintained. Refer to manufacturer’s instructions and local codes for precautions required for passing chimney through a combustible wall or ceiling. Inspect and clean exhaust venting system frequently in accordance with manufacturer’s instructions. Use a 3” or 4” diameter type “L” or “PL” venting system. Do not connect this unit to a chimney ue servicing another appliance. FOR USE WITH PELLETIZED WOOD FUEL OR A SHELLED CORN/PELLET  Input Rating Max:5.7 lb. fuel/hr Electrical Rating: 240 VAC, 50 Hz, Start 2.6 AMPS, Run 2.0 AMPS U.S. Electrical Rating: 115 VAC, 60 Hz, Start 4.2 AMPS, Run 3.6 AMPS Emissions of CO in Combustion: Normal Heat Output: <.02%, Reduced Heat Output: <.04% Flue Gas Temperature: 224 C Thermal Output: 10.5kW Energy Efciency: Normal: 84%, Reduced: 73% Fuel Type: Wood Pellets, 5mm diameter, 20mm long Shelled corn, when mixed with pellets Route power cord away from unit. DANGER: Risk of electrical shock. Disconnect power supply before servicing. Replace glass only with 5mm ceramic available from your dealer. For further instruction refer to owner’s manual. Keep viewing and ash removal doors tightly closed during operation.
Report #/Rapport #135-S-10b-2



This model is exempt from
EPA certication under
40 CFR 60.531 by denition
[Wood Heater (A) “air-to-fuel ratio”].
12"
2.25"
6.25"
6.25" 5” min.
5” min.
A
A
C
B
USA
CANADA
Floor protector
54"
2.25"
14.75" 14.75"
24"

352 Mountain House Road, Halifax, PA 17032 (
Date of Manufacture / Date de fabrication
2013 2014 2015 JAN FEB MAR APR MAY JUN JUL AUG SEP OCT NOV DEC
BARCODE LABEL
Modèle : ACCENTRA-2
Appareil de chauffage à granulés de bois
Test réalisés par OMNI-Test Laboratories, Inc. Rapport # 135-S-10b-2 Essais Selon les normes 1509-04 de l’ASTM, ULC S627-00 and ULC- C1482-M1990 Appareil de chauffage à granulés (UM) 84- HUD  NF EN 14785 CETIAT – Déc. 2006 AEMC MESURES EN50366 – Déc. 2006 EMITECH, APAVE & BFP Electronique – Fév. 2004 EN55014-1, EN 55014-2, EN 61000-3-2, EN 61000-3-3 PREVENTION DES INCENDIES Respecter scrupuleusement les instructions du constructeur pour l’installation et les consignes de fonctionnement. Respecter les règles de sécurité en vigueur dans votre région.     Ne pas installer dans une
chambre. ll est inpératif de prévoir une prise d’air extérieur. L’intégrité structurale du plancher, du plafond et des murs doit être strictment préservée. Se reporter aux instructions du fabricant et aux réglementations spéciques locales concernant les précautions requises lors de la traversée d’un mur ou d’un plafond. Contrôler et nettoyer fréquemment toul le système d’évacuation des fumées conformément aux recommandations du constructeur. Utiliser des conduits « spécial granuléls » de diamètre 80 mm ou 100 mm. Ne pas raccorder ce poêle à un conduit de cheminée déjà utilisé.  SE CONFORMER AUX INSTRUCTIONS D’UTILISATION Consommation maximale: 2.16 kg/h Caractéristiques électriques: 240VC, 50 Hz, Intensité au démarrage 2.6 A, Intensité fonctionnement normal 2.0 A Tenir le cordon d’alimentation à l’écart du poéle.
éRICAINE POUR LA PROTECTION DE L’ENVIRONMENT
C
PROTECTION DU PLANCHER USA CANADA Côtés (A) 6” 200mm Arrière (B) 0” 200mm Avant (C) 6” 450mm
Harman Accentra-2 Pellet Stove Label measures: 5.25" high X 11.5"wide
008

No
Rev C
P.N. 3-90-247
Please copy
your serial
 number
fromthelabelonyourstovetothe boxbelow.
SERIAL NUMBER
SAMPLE LABEL

3
3-90-08326R25_06/13
= Contains updated information

Introduction
ESP Control 5
Automatic Operation 6
Manual Operation 8
Assembly & Installation 10
Venting 15
Maintenance 22
Trouble-Shooting 27
Specications 28
Wiring Diagram 30
Corn Instructions 31
Warranty 33
Service Parts 35
Thisheatingappliancedoesnotjusthaveautomaticignition,ithastotalautomatictemperaturecontrol.TheAccentrahas
aninputheatrangefrom0to40,000BTU's.Thispatentedfeedsystemhasamaximumfeedrateof5lbs.perhouranda
minimum(maintenance)feedrateof.75lbs.perhourandthen"off"ifnecessary.Thehopperholdsapproximately50pounds
offuel.Theunithasaneasytocleancombustionsystemwithanashpanthatholdsashfrom1tonofburnedpremiumpellets.
Thecontrolisdesignedforeasyandefcientoperation.Ithas2automaticmodesofoperationand2manualmodesof
operation.
TheAccentrausesasmallroomsensorratherthanawallthermostatformoreaccuratetemperaturecontrol.Thisunitis
equippedwithseveraldifferentsafetydeviceswhichwillbeexplainedlaterinthismanual.Withitsspeciallydesignedburn
potandthe"AdvanceIgniter"AutomaticIgnitionSystem,theunitcanburnalargevarietyofpelletizedfuelswithvarying
ashcontent.Theaccordionstylecastironheatexchangersystemallowsmaximumsurfaceareaforthemostefcientheat
transferinasmallerrebox.
ForYourSafety:Wheninstallingasolidfuelappliance,itisalsorecommendedtoinstallSmokeandCarbonMonoxideDetectors
oneverylevelofthehouse.Duringtheinitialringoftheappliance,somesmokeorodormayoccurduetopaintcuring.You
maywanttokeepsomewindowsopenforventilationduringtherstfewhoursofburningtopreventsmokedetectoractivation.
Testyoursmokeandcarbonmonoxidedetectorsregularly.
SAFETYNOTICE:IFTHIS Harman®ACCENTRA PELLET
STOVEISNOTPROPERLYINSTALLED.AHOUSEFIREMAY
RESULT.FORYOURSAFETY,FOLLOWTHEINSTALLATION
DIRECTIONS. CONTACT LOCAL BUILDING OR FIRE
OFFICIALSABOUT RESTRICTIONSAND INSTALLATION
INSPECTIONREQUIREMENTSINYOURAREA.
Safety testing by Omni-Test Laboratories




352MountainHouseRoad
Halifax,PA17032
www.harmanstoves.com
Table of Contents


4
3-90-08326R25_06/13
ESP Control
3 Blinks:IndicatesthattheESP(ExhaustSensingProbe)
hasgoneoutofrangetoomanytimes.Iftheunitseemsto
beoperatingcorrectly,performamanualreset*.
4 Blinks: Can occur only in Room Temp Mode and
indicatesRoomSensingProbefailedornotinstalled. If a
RoomSensingProbeistheninstalled,thestatuslightwill
automaticallyreset.
NOTE:Unitwillnotstartin"AUTO"withthisstatuserror.
5 Blinks (In Igniter Auto. Mode Only):Indicatesthattheunit
hasfailedtolightwithinthe36minutestartcycle.Toreset-
TurnModeSelectorto"OFF",thenturntoeithermodeagain.)
6 Blinks :Indicatesthatthecontrolhascalculatedpooror
incompletecombustionoccurringformorethan25minutes.
Asixblinkstatusmaybesetifthestoveisallowedtorunout
ofpellets.Toreset,turnmodeselectorto"OFF"thenback
ontothedesiredmode.Iftheunitwasnotoutofpellets,see
Troubleshootingsection,Page27,formoredetails.
* Manual reset-disconnectpowercordforafewseconds
andreconnect.IferrorstilloccurscallyourDealer.
Mode Selector
Allows you to choose between Room Temp
Mode, Stove Temp Mode, or OFF. Also allows you
to vary the distribution blower speed by turning
the knob to the high or low side of each mode.
Feed adjuster
Sets the maximum feed
rate
Test
Runs all motors at full
speed for one minute
to check operation.
After a minute, the
control will simulate a
minimum burn and the
combustion blower will
remain on low.
Distribution Blower
speed adjustment
range.
L = low
H = high
Variable speed
anywhere between L
and H; although as the
stove temp. goes up, so
does the L and H scale.
Power Light
Indicates power to the
control.
Indicates power to the
feed motor.
Indicates power to
combustion blower
Status Light
Will be lit in either stove
or room temp mode
when pointer is not
within off position band
except after normal
shut down. Blinks to
indicate errors listed
below.
Indicates power to
distribution blower.
Indicates igniter is on.
Igniter switch
Set to appropriate
Start-Up mode.

Allows you to adjust
the room temperature
in Room Temp Mode
using the outer scale
marked in degrees
Fahrenheit. It also
allows you to adjust
the stove temperature
while in Stove Temp
Mode using the inner
scale marked from 1
to 7.
Dealer Diagnostic Port
For dealer maintenance only. Requires
special DDM monitor supplied to
Harman® Dealers exclusively.
Status light error messages:

5
3-90-08326R25_06/13
TheAccentra pellet stove is more than just automatic ignition, it is also automatic
temperaturecontrol.Theautomaticsystemwillallowtheresizetobeadjustedtomatch
theheatingneedsandevenputthereoutifnecessary.Ifheatisneededafterthereis
out,theAccentrawillautomaticallyre-igniteandadjusttheresizetomatchtheheating
need.Thetotallyautomaticroomsensormodeisrecommendedbecauseofitsefciency.
Theunitcanbeswitchedbetween"AUTO"and"MANUAL"atanytimeduringoperation.
Igniter switch to "AUTO"
Room Temperature Mode
In"RoomTempMode"heatoutputiscontrolledautomatically
bytheRoomSensingProbe.WhentheRoomSensingProbe
callsforheat,thestovewillincreaseoutput.WhentheRoom
SensingProbeisgettingclosetothesettemperature,the
stovewillbegintoleveloffoutputandkeepthereburning
atjusttherighttemperaturetomaintainthatsetting.
Highoutputislimitedbythefeedratesetting.Thecontrol
will feed what it needs to meet the demand, UP TO the
rate allowed by the FeedAdjuster dial setting. The unit's
maximumburnrateshouldnot create less than 1"ofash
ontheburnpotfrontedge(SeeFig.4).Overfeedingisnota
safetyconcern,butfuelmaybewastedifunburnedpellets
fallintotheashpan.
In"RoomTempMode"aconstantfuelconsumptionrateis
sacricedforexactroomtemperature.Therefore,asitgets
coldermorepelletswillbeburnedautomatically.
The distribution blower speed will vary according to the
positionofthemodeselectorpointer,andresize.
Igniter switch to "AUTO"
Stove Temperature Mode
Thisallowsforautomaticignitionuponstart-uponly.Theunit
canthenbesetatanydesiredsetting.Theheatoutputand
fuel consumption will remain constant regardless of room
temperature (See Fig 2). The unit's maximum feed rate
shouldnotcreatelessthan1"ofashontheburnpotfront
edge(SeeFig4).
Theunit'slow burnormaintenancesettingis aslowasit
willgo.Itwillnotgooutunlessitrunsoutoffueloristurned
to"off".
Shut-Down Procedure
To kill the re or stop burning the stove, turn the Mode
Selectorto"OFF".Thiswillcausetheretodiminishand
burnout.Whenthereburnsoutandthestovecoolsdown
everythingwillstop.
Ifyoupulltheplugtoshutdownthestove,allmotorswillstop.
Thismaycauseincompletecombustionandsmokeinthe
rebox.Iftheloaddoorisopenedthesmokemayescape.
Thebestwaytoshutdownthestoveissimplyletitrunout
ofpellets,thenthestovewillshutdownautomatically.
Automatic Ignition/Operation
Fig. 2
This setting will produce a room temperature
of 70 degrees with the distribution blower at medium speed.
This setting will produce medium heat with the distribution
blower on "low".
This setting will produce continuous maximum heat output
with the distribution blower at full speed.
Stove Temperature Mode
Fig. 1
...
...

6
3-90-08326R25_06/13
See Hint #7.
1"
Igniter Switch to "AUTO" (down position)
Makesuretheunitispluggedintoa120VAC,60Hzelectrical
source.Thepowerlightshouldbetheonlylightlit.
IMPORTANT: Toavoidunwantedsmoke,Besurethereis
nofuelorothercombustiblesintheashpanpriortolighting.
Keep all doors closed during operation.Maintainallseals
andgasketsingoodcondition.
Useonlytheburnpot,assuppliedintherebox,tosupport
orcontaintheburningfuel.Nootherformofgrateorrack
ispermitted.
1. Turn Mode Selector to "OFF".
2. Fill hopperwithpellets.
3. Clean burn pot withscraper,ifnecessary.
4. If starting after an empty hopper, turn Feed Adjuster
to "TEST" (forone60secondcycle).Thiswillfeedpellets
intotheaugertubeandalsoallowyoutocheckthemotors
foroperation.NOTE: The auger motor will not operate
with the view door or ash pan door open.
5. Turn Feed Adjuster to #4.
6. Flip the Igniter Switch down intothe"AUTO"position.
7. Turn the Temperature Dial to the desired room
temperature.
8. Turn the Mode SelectortoRoomTemperatureorStove
Temperature.
9. Fill the hopper with pellets and remove ashes as
required.
Automatic Start Up
Helpful Hints
1. Fines are small pieces of broken pellets (sawdust). Fines do
not ow easily and often build up on the hopper funnel bottom
angles. These nes can be pushed into the feeder opening and
then ll the hopper with pellets. As the system works, they will
be burned.
2. The "TEST" cycle will operate the feeder motor for exactly one
minute. Turning to "TEST" again and again may feed too much
fuel into the burn pot causing excessive smoke on start-up.
3. The rebox low pressure switch will not allow the auger motor
or the igniter element to operate if the view door is open.
4. Adjust Feed Rate. If this is your rst re or you are trying different
pellets, set the feed adjuster to #4, Fig. 3. This is a conservative
number and will probably need to be increased. After you know
a feed rate setting that works well, use that setting. Remember,
if your feed rate is too high you may waste fuel.
5. This is usually a weekly maintenance procedure. Cleaning the
burn pot with the scraper with a small amount of new fuel in the
bottom is not a problem. First, scrape the ashes on the front of
the burn pot into the ash pan. Then scrape the holed surface
downward into the burn pot. When the stove is ignited these
scrapings will be pushed out by the feeder.
6. The ash pan can hold the ashes from approximately 1 ton of
premium fuel. This means the ashes will only need to be emptied
a few times a year.
7. Setting the feed adjuster # for maximum burn: With the unit
burning in "AUTO", turn to "Stove Mode" and put the fan on
"H". Set the Temperature Dial to #7. Allow the unit to burn for
about 30 minutes and check ash on front of burn pot. Fig. 4. If
the ash line is larger than 1", turn the feed adjuster from #4 to
#5. Allow another 30 minutes of burn time and check again. If
, at #6 setting, a 1" or less ash bed is not obtainable, it is not a
problem. The 1" ash bed is only a maximum burn rate and at
most normal settings the ash bed will be larger.
Fig. 3
Fig. 4
CAUTION
DO NOT USE CHEMICALS OR FLUIDS TO START
     
   


      

Starting First Fire
NOTE: ALL PACKAGING & SHIPPING MATERIALS
MUST BE REMOVED FROM THE STOVE BEFORE
OPERATING.

7
3-90-08326R25_06/13
TheAccentra Pellet Stove is capable of manual operation. This allows the operator to
manuallycontroloperationandfuelconsumption.Manualoperationcanalsobehelpful
duringanemergency(i.e.igniterfailure,orwhenusingcertaingenerators.)Theunitcan
beswitchedbetween"AUTO"and"MANUAL"atanytimeduringoperation.
Igniter Switch to "MANUAL"
Room Temperature Mode
Therewillhavetobelitwithstartinggelandamatch,or
started automatically, see "Automatic Operation". Turn to
"Manual"positionwhenthereisestablished.
Thedifferencebetween"AUTO"RoomTemperatureMode
and"Manual"RoomTemperatureModeisthattherewillnot
gooutastheroomtemperaturegoesabovethecontrolboard
setting.Theunitcanonlygotolowburnandwillremainthere
untilitrunsoutoffueloruntilmoreheatisneededandthe
feedrateincreases.Feedrateadjustmentsanddialsettings
arethesameas"AUTO"settings.
Igniter Switch to "MANUAL"
Stove Temperature Mode
Theadvantageofthismodeistoallowtheoperatortohave
alargeviewingrewithoutblowingextraheatintotheroom.
Duringoperation,withthetemperaturedialsetat#4orless,
thedistributionfanwillnotoperate.A#3onthetemperature
dial and a #4 on the feed adjuster is approximately 80%
output. The distribution blower will not operate below this
point.Therefore,therecanbeahigherfeedrate(alarger
viewingre) without an excess of hot air blowing intothe
room.
AnexampleofwhentousetheManualStoveTemperature
Modeisifyou want towatchalargereand the roomis
alreadyuptotemperature.TheStoveTemperatureMode
allows you to have a larger re and a lower sound level,
withoutthedistributionblower.
NOTE: During the use of this mode, if you keep increasing
the temperature dial setting to increase the re size, the
distribution blower will automatically come on when the
ESP Temperature reaches 350°F, or 81% output.
NOTE: When starting the unit in the "AUTO" mode,
switching to "MANUAL" can be done at any time. Once
an ignition cycle is started, it will continue, regardless
of mode. There is no need to wait for the ignition cycle
to complete.
Manual Ignition/Operation
This setting will produce a room temperature
of 70 degrees with the distribution blower at medium speed.
Fig. 5
This setting will produce a large viewing re without a distribution
blower operating.
Manual Stove Temperature Mode
Fig. 6
...
...
Shut-Down Procedure
TurntheModeSelectorto"OFF".Thiswillallowtheretodiminishandburnout.WhenthereburnsoutandtheESPcools,
everythingwillstop.Neverpulltheplugtoshutdownthestove.Thiswillcauseincompletecombustionandsmokeinthe
rebox.Iftheloaddoorisopenedthesmokemayescape.
Thebestwaytoshutdownthestoveissimplyletitrunoutofpellets,thenthestovewillshutdownautomatically.

8
3-90-08326R25_06/13
1"
See Hint #7.
Manual Start Up
Igniter Switch to "MANUAL" (up position)
Makesuretheunitispluggedintoa120VAC,60Hz
electricalsource.
IMPORTANT: Toavoidunwantedsmoke,Besurethereis
nofuelorothercombustiblesintheashpanpriortolighting.
Keepalldoors closedduringoperation.Maintain allseals
andgasketsingoodcondition.
Useonlytheburnpot,assuppliedintherebox,tosupport
orcontaintheburningfuel.Nootherformofgrateorrack
ispermitted.
1. Turn FEED ADJUSTER to the desired feed rate.No.4
isgoodformostpellets.4
2. Turn the MODE SELECTOR to “OFF” and then to the
desired mode.Thiswillresetthecontrolandstartthe
combustionmotor.
3. Turn the TEMPERATURE DIAL to the desired setting.
4. Clean the burn pot with the scraper, if necessary.5
5. Fill the burn pot with pellets, only level with front edge.
(DoNotOverFill).
NOTE: If an automatic ignition was attempted - Be sure
to give the appliance at least 30 minutes of cooling time
before proceeding with these instructions.
6. Add starting gel on top of the pellets.Stirthegelinto
pelletsforfasterlighting.
SEE CAUTION BELOW.Theuseofastartinggelthatis
commerciallymarketedforusewithpelletstovesispermitted
ONLYwhenperformingacoldstart.Alsobesuretoperform
theabovestepsinsequencetoensurecombustionblower
operationbeforeapplyingthestartinggel.Followthestarter
manufacturer'sinstructionsforproperapplication.
7. Light the starting gel with a match, and close the door.
Operation will begin when the re reaches the proper
temperature.
8. Fill the hopper with pellets and remove ashes as
required.
Helpful Hints:
1. Fines are small pieces of broken pellets (sawdust). Fines do
not ow easily and often build up on the hopper funnel bottom
angles. These nes can be pushed into the feeder opening and
then ll the hopper with pellets. As the system works, they will
be burned.
2. The "TEST" cycle will operate the feeder motor for exactly one
minute. Turning to "TEST" again and again may feed too much
fuel into the burn pot causing excessive smoke on start-up.
3. The rebox low pressure switch will not allow the auger motor
or the igniter element to operate if the view door or the ash pan
door are open.
4. Adjust Feed Rate. If this is your rst re or you are trying different
pellets, set the feed adjuster to #4, Fig. 7. This is a conservative
number and will probably need to be increased. After you know
a feed rate setting that works well, use that setting. Remember,
if your feed rate is too high you may waste fuel.
5. This is usually a weekly maintenance procedure. Cleaning the
burn pot with the scraper with a small amount of new fuel in the
bottom is not a problem. First, scrape the ashes on the front of
the burn pot into the ash pan. Then scrape the holed surface
downward into the burn pot. When the stove is ignited these
scrapings will be pushed out by the feeder.
6. The ash pan can hold the ashes from approximately 1 ton of
premium fuel. This means the ashes will only need to be emptied
a few times a year.
7. Setting the feed adjuster # for maximum burn: With the unit
burning in "AUTO", turn to "Stove Mode" and put the fan on
"H". Set the Temperature Dial to #7. Allow the unit to burn for
about 30 minutes and check ash on front of burn pot. Fig. 9. If
the ash line is larger than 1", turn the feed adjuster from #4 to
#5. Allow another 30 minutes of burn time and check again. If
, at #6 setting, a 1" or less ash bed is not obtainable, it is not a
problem. The 1" ash bed is only a maximum burn rate and at
most normal settings the ash bed will be larger.
Fig. 8
Fig. 7
Fig. 9
CAUTION
DO NOT USE CHEMICALS OR FLUIDS TO START
     
   


      

Manual "Cold" Start

9
3-90-08326R25_06/13
Placethestoveonanoncombustibleoorsurfaceoroor
protector.Thiscanbeaminimumofa20gaugesheetmetal
plate,ceramictilewithgroutedjoints,aULlistedstoveboard,
oraHarman®CastIronoorprotector. TheHarman®Cast
IronFloorProtectorisequaltotheminimumdimensions,which
are241/16"
x285/8".Thisallowsfora2"extensiononeachside
of the unit (which is actually 6 inches from the window
opening) and a 6" extension to the front (measured from
the windowopeningalso)(33/8"ifmeasuredfromthebase
platefrontedge.)Therearedgeoftheoorprotectioncan
beushwiththecastbaseplaterearedge.
NOTE for Canadian installation only:PerULC-S627-00,
If installed on a combustible oor, the need to provide a
noncombustible oor protector covering the area beneath
thespace heater andextendingatleast17.72"(450mm)on
theringsideandatleast7.87"(200mm)ontheothersides.
In Canada, you may follow smaller U.S. oor protection
requirements ONLY if the user agrees to completely
shut-down the appliance, and allow it to cool to where
all re is extinguished and the combustion blower and
its indicator light shuts off, prior to opening the rebox
door or ash door.
Floor protection is required under any horizontal venting.
Thisprotectionmustextend2inches(5.8cm)beyondeach
sideofthehorizontalpipe.
Installation
CAUTION
HOT WHILE IN OPERATION.
KEEP CHILDREN, CLOTHING AND FURNITURE AWAY.
CONTACT MAY CAUSE SKIN BURNS.
DO NOT CONNECT TO ANY AIR DISTRIBUTION DUCT
OR SYSTEM.
INSTALL VENT AT CLEARANCES SPECIFIED BY THE
VENT MANUFACTURER.
DO NOT USE MAKESHIFT COMPONENTS OR
COMPROMISESWHENINSTALLINGTHISAPPLIANCE.
YOUR SAFETY IS A SERIOUS CONCERN.
L
J
Floor Protection
Requirements US Canada
Sides
Rear
6" 200mm
0" 200mm
KFront 6" 450mm
J
Canada
J
USA
K
L
NOTE:Measurement
"K"ismeasuredfrom
theglassintheUS
ONLY
Floor protector
Harman®CastIron
FloorProtectorsize:
241/16(611mm)X
285/8(727mm)

10
3-90-08326R25_06/13
WheninstallingandoperatingyourHarman®AccentraPelletStove,respectbasicsafetystandards.Readtheseinstructions
carefullybeforeyouattempttoinstalloroperatetheAccentra.Failuretodosomayresultindamagetopropertyorpersonal
injuryandmayvoidtheproductwarranty.
SeveralissuesmustbeaddressedwhenselectingasuitablelocationforyourAccentraPelletStove.Observingrequired
clearancestocombustiblematerials,theproximitytoasafechimneyorventingsystem,andtheaccessibilityofelectrical
supplymustallbeconsidered.
Placethestoveawayfromcombustiblewallsatleastasfarasshowningures10,11,&13.
Clearances May Only be Reduced Using Methods Approved by the Regulating Authority Having Jurisdiction.
Notethattheclearancesshownareminimumforsafetybutdonotleavemuchroomforaccesswhencleaningorservice
isneeded.
TheClearancetoTheTopofTheUnitis60"(152cm)MeasuredFromThe
Floor.
5” min.
5” min. 6.25"
159mm
6.25"
159mm
Fig.11 12"
305mm
2.25"
57mm


"
5/8
This is the minimum size Harman® recommends for an
alcove with a 60" ceiling.
Fig. 13
54"
24"
24"
2.25"
14.75" 14.75"

11
3-90-08326R25_06/13
Installation
IMPORTANT NOTE: TheAccentraisshippedboltedtothe
skidthroughtwoholesinthecastbaseplate.Iftheseholes
arenotusedtolagtheunittotheoortheseholesmustbe
lledwiththe3/8"x1/2"hexheadboltsprovided.(Seetag
onboltbagprovided.)
Skid bolt down holes/oor lag down holes
Fig. 14
Optionalkit#1-00-12302contains4rubberpadfeet.Used
toraisethebottomedgeofthecastbaseplateofftheoor
surface,theyensurethatanyvibrationscausedbymotors
and other moving parts will not be transferred by direct
contact. These rubber pads have a threaded stud that
extendsthroughthebaseplate.Thetopofthethreadedstud
hasascrewdriverslot.Therefore, the unit can be leveled
fromaboveinsidetheunit.Thefronttwoareintherightand
leftfrontcornersoftherebox.NOTE:Thedoorwillneedto
bepartiallyclosedtoaccesstherightlevelingpadstuddue
tothedoorhinge.
Thereartwostudsaretotherightandleftofthedistribution
blower.Theyaresomewhatdifculttoreach,therefore,itis
suggestedthatthereartwopadsbeadjustedbytiltingtheunit
slightlyforward.Adjustthepadswithyourngersandtiltunit
backfort.Thenadjustthefrontpadsforthenalclearance.
Thereisa leg kit available for theAccentra (Item # 1-00-
247211).Thefourcastironlegsbolttoaplate,andthestove
thensitsontheplate.Therubberlevelingfeetareremoved
toallowthestovetotdownoverthelegplate.Thelegkit
adds2.95inchesinheight.Thelegkitcanalsobeusedin
conjunctionwiththecastoorprotector.Ifusingwiththecast
oorprotector,aoorprotectorcoverisalsoneededsince
thelegsallowviewingunderneaththestove.
Leg Kit includes; four
legs, mounting plate
and hardware.
DO NOT BLOCK OR OBSTRUCT THE AREA BENEATH
THE APPLIANCE. THIS AIRFLOW IS CRUCIAL TO SAFE
OPERATION AND CLEARANCES TO COMBUSTIBLES.
Optional Rubber Pad Leveling Feet
Optional Leg Kit
Leveling/vibration-dampening feet
Fig. 15
NOTE: ALL PACKAGING & SHIPPING MATERIALS
MUST BE REMOVED FROM THE STOVE BEFORE
OPERATING.

12
3-90-08326R25_06/13
AFTER THE INSTALLATION IS COMPLETE
Beforetherstreislit,checkandrecordthehighandlow
draftreadingnumbersonpage13.Makeadjustmentstothe
lowdraftatthistime,ifnecessary.
MOBILE HOME INSTALLATION SHOULD BE DONE IN
ACCORDANCE WITH THE MANUFACTURED HOME AND
SAFETY STANDARD (HUD), CFR 3280, PART 24.
Unit bolt down holes for mobile home installation lag to oor
with 1/4" diameter lag bolts with washer. (not supplied.) Note:
If the optional leg kit is used, a longer bolt will be required.
Mobile Home Installation
Fig. 16
CAUTION
THE STRUCTURAL INTEGRITY OF THE MOBILE
HOME FLOOR, WALL, AND CEILING/ROOF MUST BE
MAINTAINED.
CAUTION
THE STOVE IS HOT WHILE IN OPERATION.
KEEP CHILDREN, CLOTHING AND FURNITURE AWAY.
CONTACT MAY CAUSE SKIN BURNS.
WARNING
KEEP COMBUSTIBLE MATERIALS SUCH AS GRASS,
LEAVES, ETC. AT LEAST 3 FEET AWAY FROM THE
POINT DIRECTLY UNDER THE VENT TERMINATION.
WARNING! DO NOT INSTALL IN SLEEPING ROOM
Canadian Standard ULC S627 requires that all outdoor-
aired space heaters must be attached to the structure.
When installing theAccentra in a mobile home several
Requirements must be followed:
1. Theunitmustbeboltedtotheoor.Thiscanbedonewith
1/4"lagscrewsthroughthe2holesinthebaseplateshown
inFig.16
2. Theunitmustalsobeconnectedtooutsideair.Seepage
15.
3. Floor protection and clearances must be followed as
shownonpage10.
4. Unitmustbegroundedtothemetalframeofthemobile
home.
5. Chimney must meet requirements of CAN/ULC-S629,
Standard for 650°C Factory Built Chimneys. Follow
Manufacturer's guidelines concerning height and
clearancestocombustibles.Usethesamemanufacturer's
componentstoprovideaneffectivevaporbarrierwhere
thechimneyorothercomponentpenetratestotheexterior
ofthemobilehome.DO NOT MIX COMPONENTS FROM
DIFFERENT MANUFACTURERS. The top section of
chimneyandthechimneycapmustberemovabletoa
maximumheightof13.5'fortransportofthemobilehome.
CAUTION: This appliance must be vented to the outside.
Duetohightemperatures,theAccentrashouldbeplaced
outoftrafcandawayfromfurnitureanddraperies.Children
andadultsshouldbealertedtothehazardsofhighsurface
temperaturesandshouldstayawaytoavoidburntoskinand/
orclothing.Youngchildrenshouldbecarefullysupervised
whentheyareinthesameroomasthestove.Clothingand
otherammablematerialsshouldnotbeplacedonornear
theAccentraPelletStove.
InstallationandrepairoftheAccentraPelletStoveshould
bedonebyaqualiedserviceperson.Theapplianceshould
beinspectedbeforeuseandatleastannuallybyaqualied
service person. More frequent cleaning will be required.
It is imperative that control compartments, burners, and
circulatingairpassagewaysoftheAccentrabekeptclean.

13
3-90-08326R25_06/13
       

The small straight screwdriver slot is plastic; therefore, the
unit can be adjusted while in operation.
Theseunitsarepre-testedatthefactorywithexactly120VAC,
60Hz.Theyarecheckedandadjustedforreboxtightness,
gasketleakage,motoroperationandigniteroperation.The
Accentraisthenfactorysetatahighadjustment.
NOTE: Low draft adjustment may be required. The
factory low draft setting may not be correct for the units
permanent installation conditions.
ThecontrolboardontheAccentraisequippedwithalowdraft
adjustmentport.Locatedonthecontrolfacejusttotheleft
oftheigniterlight.SeeFigure17.Thisvoltageadjustment
isprovidedtoallowtheunittobeadjustedforthehousehold
voltagewheretheunitisgoingtobeinpermanentoperation.
NOTE:Thelinevoltagevariesfromareatoareaandoften
hometohome.
Thelowdraftvoltageshouldbeadjustedtoachievethemost
efcient burn on low burn or "maintenance". This voltage
adjustment allows the installer to change the low voltage
set point approximately 15 volts.  This adjustment should
bedonebytheinstallerduringsetupbecauseadraftmeter
readingisrequired toensurepropersetup.
Iftheunitisnotadjustedproperly,itdoesnotcauseasafety
concern.Iftheunitisadjustedtoohigh,onlyefciencyislost.
Iftheunitisadjustedtoolow,thelowdraftpressureswitch
willnotallowthefeedermotorortheignitertooperate.
Asimpledrafttestshouldbeperformedaftercompletingthe
uepipeinstallation.Recordtheresultsforfuturereference:
1. Plugunitintoa120VAC,60Hzoutlet.
2. Closethehopperlidandfrontviewdoor.Neitherpellets
orarearerequiredforthistest.
3. Withthemodeselectorinthe"OFF"position,turnthefeed
adjusterto"TEST".
4. Record the high draft_____in. W.C. (Normal is -.45 to
-.55)ThecontrolwillbeontheHighDraftforatotalof1
minute.
5. After1minute,thecombustionmotorwillgodowntolow
draft and the distribution blower will go on high.Allow
approximately 15 seconds to pass for the combustion
motortoslowbeforecheckingthelowdraft.
6. Ifthelowdraftisbetween.30and.35,recordthereading
_____in.W.C.Ifthereadingishigher,slowlyturnthe
setscrewcounter-clockwiseuntilthedraftlowers.Ifthe
readingislower,veryslowlyturnthesetscrewclockwise
untilthedraftincreases.
NOTE: In some cases, the draft may not go as low as .30
even with the set screw completely counter-clockwise.
Fig. 17 Fig. 18
Low Draft Voltage Adjustment



MAGNEHELIC
INCHES OF WATER
0
.10
.20
.30
.40
.50

14
3-90-08326R25_06/13
Theroomsensorisasmalltemperaturesensorontheendof
a60"wire.Thissensorisinstalledmuchlikeastandardwall
thermostat.Becauseitissosmall,itcanbehiddenalongthe
trimofadoorwayorevenupthelegofacoffeetable.There
isaremoteroomsensorportontherearoftheunitforeasy
externalconnection.Usestandard18-2thermostatwireto
extendthedistancetothedesiredlocation(100'maximum).
Theroomsensorshouldbeinstalledinthelocationwhere
youwanttocontrolthetemperature.
NOTE:Distancesofmorethan25feetfromtheunitorin
another room are not recommended. The room sensor is
essentialfortheAccentra'sexcellentefciency.
It is recommended that the room sensor be installed,
evenifonlyinstalledontherearoftheunitasareturnair
sensor.Thereisanintakescreenonthebottomoftherear
sheetmetalenclosure.Thisisanidealplacetotiewrapthe
sensorheadtosensereturnairtemperature.
Fig. 19
Room Sensor Installation
Room Sensor and Rear Shield Installation
Rear Shields
Fig. 20
5/16" Hex Head
Screws (2 on
each side)
5/16" Hex Head
Screws (2 on
each side)
Therearinsulatedshieldsaresplitinthemiddle for easy
removal.Eachshieldhastwo5/16"hexheadscrewsthatonly
needtobeloosened(NOTREMOVED)toallowtheshield
toslideawayfromtheunit.NOTE: It is not recommended
that the unit be operated with the shields removed, due
to the hot and moving parts which they protect.
Donotallowpelletsorsawdusttobuilduponthehopperlip.
Inspectthehopperlidgasketfordamage.Agoodhopperlid
sealisveryimportantforproperoperation.
Fig. 21
Hopper Lid Foam
Gaskets
Hopper lip
REMINDERS
NOTE: ALL PACKAGING & SHIPPING MATERIALS
MUST BE REMOVED FROM THE STOVE BEFORE
OPERATING.

15
3-90-08326R25_06/13
Venting
A combustion blower is used to extract the combustion
gasesfromtherebox.Thiscausesanegativepressurein
thereboxandapositivepressureintheventingsystemas
showning.22.Thelongertheventpipeandmoreelbows
usedinthesystem,thegreatertheowresistance.Because
ofthesefactswerecommendusingasfewelbowsaspossible
and15feetorlessofventpipe.Themaximumhorizontalrun
shouldnotexceed48".Ifmorethan15feetofpipeisneeded,
thediametershouldbeincreasedfrom3"to4"becausea
larger pipe causes less ow resistance. Be sure to use
approved pellet vent pipe wall and ceiling pass- through
ttings to go through combustible walls and ceilings.
Besuretouseastartingcollartoattachtheventingsystem
tothestove.The starting collar must be secured to the
heater with a minimum of three fasteners. Thescrews
providedareaself-drillingtypeofscrew.However,dueto
materialthickness,drillinga3/32"pilotholeisrecommended
foreachscrew.Youmayalsowishtosealthisconnection
withRTVsiliconecaulking.
NOTE: Simpson DuraVent PelletVent Pro Harman®
Adapter Part #3PVP-ADHB and PelletVent Pro Harman®
Adapter Increaser Part #3PVP-X4ADHB are highly
recommended to be installed on the starter collar to
insure a proper pipe connection to the unit.
Venting
IMPORTANT NOTICE
3or4inchPelletVentPipe-
(TypePL)Mustbeused.
Outside air ex pipe
goes here
Room Sensor
Connection Ports
3" PL vent
pipe ue collar
Fig. 23
-
+
+
= Positive static pressure
= Negative static pressure
+
-
Fig. 22
Inlet Cover
(part # 1-10-08542)
25' Flex pipe
(part # 1-00-08543)
Fig. 24
Direct Vent Wall Passthrough
Kit (part #1-00-677077)
Fig. 24b
Pelletventingpipe(alsoknownasPLvent)isconstructed
of two layers with air space between the layers. This air
spaceactsasaninsulatorandreducestheoutsidesurface
temperaturetoallowaclearancetocombustiblesofonly3
inches.Thesectionsofpipelocktogethertoformanairtight
sealinmostcases;however,insomecasesaperfectsealis
notachieved.ForthisreasonandthefactthattheAccentra
operateswithapositiveventpressure,we specify that the
joints also be sealed with high-temp silicone.
Vent Pipe
Connection to outside air is strongly recommended. It is
requiredforallmobilehomeinstallations,andwherebuilding
codesrequire.
Toinstalloutsideairuse23/8"I.D.expipe,partnumber
1-00-08543(25feet).Thereisabreak-awayholeontherear
panelwhichmustberemovedbeforeconnectingtheexpipe.
Thepipeshouldberunoutsideandterminatetothesideor
belowtheventpipeoutletsotheueoutletismorethan12"
fromtheinletcover.Themaximumlengthrunofthispipeis
15feet.Ifalongerrunisneeded,thesizemustbeincreased
to3".Inletcoverpartnumber1-10-08542shouldbeusedto
keepbirds,rodents,etc.outofthepipe.
You may choose to use the optional Direct Vent Wall
Passthrough Kit (part #1-00-677077) which incorporates
venting passthrough and outside air into one component.
SeeFig.24b.
Outside Air

16
3-90-08326R25_06/13
Venting
Avoiding Smoke and Odors
Negative Pressure, Shut-down, and Power Failure:
To reduce the probability of back-drafting or burn-back in
the pellet burning appliance during power failure or shut-
down conditions, the stove must be able to draft naturally
withoutexhaustbloweroperation.Negativepressureinthe
housewillresistthisnaturaldraftifnotaccountedforinthe
pelletapplianceinstallation.
Heatrisesinthehouseandleaksoutatupperlevels.This
airmustbereplacedwithcoldairfromoutdoors,whichows
into lower levels of the house. Vents and chimneys into
basementsandlowerlevelsofthehousecanbecomethe
conduitforairsupply,andreverseundertheseconditions.
Outside Air:
Hearth & Home Technologies recommend attaching
outside air in all installations, especially lower level and
main oor locations.
Pernationalbuildingcodes,considerationmustbegivento
combustionairsupplytoallcombustionappliances.Failure
tosupplyadequatecombustionairforallappliancedemands,
mayleadtoback-draftingofthoseandotherappliances.
Whentheapplianceisside-wallvented:Theairintakeisbest
locatedonthesameexteriorwallastheexhaustventoutlet
andlocatedloweronthewallthantheexhaustventoutlet.
When the appliance is roof vented: The air intake is best
locatedontheexteriorwallorientedtowardstheprevailing
winddirectionduringtheheatingseason.
Theoutsideairconnectionwillsupplythedemandsofthe
pellet appliance, but consideration must be given to the
totalhousedemand.Housedemandmay consume some
airneededforthestove,especiallyduringapowerfailure.It
maybenecessarytoaddadditionalventilationtothespacein
whichthepelletapplianceislocated.Consultwithyourlocal
HVACprofessionaltodeterminetheventilationdemandsfor
yourhouse.
Vent Congurations:
To reduce probability of reverse drafting during shut-
down conditions, Hearth & Home Technologies strongly
recommends:
• Installingthepelletventwithaminimumverticalrunof
vefeet,preferablyterminatingabovetheroofline.
• Installingtheoutsideairintakeatleastfourfeetbelowthe
venttermination.
Topreventsootdamagetoexteriorwallsofthehouseand
topreventre-entryofsootorashintothehouse:
• Maintainspeciedclearancestowindows,doors,andair
inlets,includingairconditioners.
• Ventsshouldnotbeplacedbelowventilatedsofts.Run
theventabovetheroof.
• Avoidventingintoalcovelocations.
• Vents should not terminate under overhangs, decks or
ontocoveredporches.
• Maintain minimum clearance of 12 inches from the
ventterminationtotheexteriorwall.Ifyouseedeposits
developing on the wall, you may need to extend this
distancetoaccommodateyourinstallationconditions.
Hearth & Home Technologies assumes no responsibility
for, nor does the warranty extend to, smoke damage
caused by reverse drafting of pellet appliances under
shut-down or power failure conditions.
Canadian Standard ULC S627 requires that all outdoor-
aired space heaters must be attached to the structure.
See page 12, Fig 16.
WARNING! CHIMNEY AND CONNECTOR MUST
BE MAINTAINED IN GOOD CONDITION AND KEPT
CLEAN.
DO NOT INSTALL A FLUE DAMPER IN THE EXHAUST
VENTING SYSTEM OF THIS APPLIANCE.
DO NOT CONNECT THIS UNIT TO A CHIMNEY FLUE
SERVING ANOTHER APPLIANCE.
CHIMNEY CONNECTOR MAY NOT PASS THROUGH
AN ATTIC OR ROOF SPACE, CLOSET OR SIMILAR
CONCEALED SPACE, OR A FLOOR OR CEILING.

17
3-90-08326R25_06/13
Venting
CAUTION
KEEP COMBUSTIBLES (SUCH AS GRASS,
LEAVES, ETC.) AT LEAST 3 FEET AWAY FROM
THE FLUE OUTLET ON THE OUTSIDE OF THE
BUILDING.
Thismethodprovidesexcellentventingfornormaloperation
andallowsthestovetobeinstalledclosesttothewall.Two
and a half inches from the wall is safe; however,  three
inchesallowsbetteraccesstoremovetherearpanel.The
verticalportionoftheventshouldbethreetovefeethigh.
Thisvertical section will provide natural draft intheevent
ofapowerfailure.Note: Do not place joints within wall
pass-throughs.
#1 Preferred method
This method also provides excellent venting for normal
operationbutrequiresthestovetobeinstalledfartherfrom
thewall.Theverticalportionoftheventshouldbethreeto
vefeethighandatleastthreeinchesfromacombustible
wall. This vertical section will provide natural draft in the
eventofapowerfailure.Note: Do not place joints within
wall pass-throughs.
#2 Preferred method
Fig. 25 3 ft.
to combustibles
Combustibles
3 ft.
to combustibles
Fig. 26 3 ft.
to combustibles
Combustibles
3 ft.
to combustibles

18
3-90-08326R25_06/13
Thismethodprovidesexcellentventingfornormaloperation.
Checkyourlocalcoderequirements.Someareasrequirethat
alinerbeinstalledtothetopoftheue,asshowninmethod
#7.Thismethodwillprovidenaturaldraftintheeventofa
powerfailure.Ifthechimneyconditionisquestionableorif
theuesizeislargerthan8X8inches,youshouldreferto
method#7.Ifchoosingthismethod,increasetheventpipe
to4in.atthestove.
Fig. 27
Venting
Fig. 28
Thismethodprovidesexcellentventingfornormaloperation.
Checkyourlocalcoderequirements.Someareasrequirethat
alinerbeinstalledtothetopoftheue,asshowninmethod
#6.Thismethodalsoprovidesnaturaldraftintheeventofa
powerfailure.
The damper area must be sealed with a steel plate (not
supplied). Kaowool, mineral wool, or an equivalent non-
combustibleinsulationisrecommendedtobeinstalledontop
ofthesealingplate.Thiswillhelptoreducecondensation.A
capshouldbeinstalledonthechimneytokeepoutrain.Ifthe
chimneyconditionisquestionableoriftheuesizeislarger
than8X8inches,youshouldrefertoMethod#6.Ifchoosing
thismethod,increasetheventpipediameterto4inchesat
thestove.
#4 Installing into an existing chimney
#5 Installing into an existing replace chimney
WARNING! CHIMNEY AND CONNECTOR MUST
BE MAINTAINED IN GOOD CONDITION AND KEPT
CLEAN.

19
3-90-08326R25_06/13
Thismethodprovidesexcellentventingfornormaloperation.
This method also provides natural draft in the event of a
powerfailure.
SomeplacesintheUSandCanada,itisrequiredthatthevent
pipeextendallthewaytothetopofthechimney.
Inthismethodacapshouldalsobeinstalledonthechimneyto
keepoutrain.Besuretouseapprovedpelletventpipettings.
Sealpipejointswithsiliconeinadditiontothesealingmethod
usedbythemanufacturer.Pipesizeshouldbeincreasedto
4"usingthismethod.
Thismethodprovidesexcellentventingfornormaloperation.
This method also provides natural draft in the event of a
powerfailure.
SomeplacesintheUSandCanada,itisrequiredthatthe
ventpipeextendallthewaytothetopofthechimney.The
pipeorlinerinsidethechimneyshouldbe4"diameterand
approvedforpelletventing.
Inthismethodacapshouldalsobeinstalledonthechimney
tokeepoutrain.
Venting
#6 Installing into an existing replace chimney
#7 Installing into an existing chimney
WARNING! CHIMNEY AND CONNECTOR MUST
BE MAINTAINED IN GOOD CONDITION AND KEPT
CLEAN.
Fig. 30
Fig. 29

20
3-90-08326R25_06/13
Min. above ground level
12"
Fig. 32
Minimum ue vent conguration
Itisrequiredthatoutsideairbeinstalled
withthisventingcongurationtoreduce
smokeandcreosotesmellintheroom
intheeventofpowerfailure.
Through the ceiling vent, follow PL vent manufacturers
recommendationswhenusingwallandceilingpassthrough.

PL vent manufacturer's
restop spacer and support No insulation or other
combustible materials
are allowed within 3" of
the PL vent pipe.
Storm collar
Flashing
3"min.
3"min.
3"min.
12"min.
(See Page 10 for
corner installation
clearances)
Fig. 31
Venting
Fig. 33
#8 Installing through the ceiling vent
12"
min. wall to outlet
36"
min. clearance to any
combustable material