Harman TL2.0 User manual

Save These Instructions Harman® • TL2.0 Owner's Manual_R20 • 2011 -___ • 09/15 3-90-08560
Owner's Manual
Installation and Operation
Model:
TL2.0
Non-Catalytic, Top Load,
Wood Burning Room Heater
Item #1-90-856000
NOTICE
• Important operating and
maintenance instructions
included.
• Read, understand and
follow these instructions
for safe installation and
operation.
• Leave this manual with
party responsible for use
and operation.
DO NOT DISCARD THIS MANUAL
Wood Stove
Use & Care Video
CHECK BUILDING CODES PRIOR TO INSTALLATION.
• INSTALLATION MUST COMPLY WITH LOCAL, REGIONAL,
STATE AND NATIONAL CODES AND REGULATIONS.
• CONSULT LOCAL BUILDING, FIRE OFFICIALS OR
AUTHORITIES HAVING JURISDICTION ABOUT
RESTRICTIONS, INSTALLATION INSPECTION, AND
PERMITS.
CAUTION
!
TESTED AND APPROVED FOR USE WITH DRY,
SEASONED CORDWOOD ONLY. DO NOT BURN WET
OR GREEN WOOD. BURNING ANY OTHER TYPE OF
FUEL WILL VOID YOUR WARRANTY.
CAUTION
!
Hot, will cause burns.
• Do not touch glass until it is cooled
• NEVER allow children to touch glass
• Keep children away
• CAREFULLY SUPERVISE children in same room
as replace.
• Alert children and adults to hazards of high
temperatures.
High temperatures may ignite clothing or other
ammable materials.
• Keep clothing, furniture, draperies and other
ammable materials away.
HOT SURFACES!
Glass and other surfaces
are hot during operation
AND cool down.
WARNING
!
Please read this entire manual before
installation and use of this wood-burning
room heater.
Failure to follow these instructions could
result in property damage, bodily injury
or even death.
• Do not store or use gasoline or other ammable
vapors and liquids in the vicinity of this or any other
appliance.
• Do not overre - If any external part starts to glow,
you are overring. Close air controls. Overring will
void your warranty.
• Comply with all minimum clearances to combustibles
as specied. Failure to comply may cause a house
re.
WARNING
!
Contact your local dealer with questions on installation,
operation or service.
To obtain a French translation of this manual, please contact your dealer or visit www.harmanstoves.com.
Pour obtenir une traduction française de ce manuel, s’il vous plaît contacter votre revendeur ou visitez www.harmanstoves.com.
Do Not
Discard

2
TL2.0 Woodburning Stove
Dry Seasoned Wood Only! Save These InstructionsHarman® • TL2.0 Owner's Manual_R20 • 2011 -___ • 09/15
May be burned as a replace with “Cozy Screen” Part# 3-40-06960 in place over door opening. Otherwise, doors must remain closed during operation
Peux fonctionner comme un foyer avec la pièce no. 3-40-06960 ‘’ Cozy Screen ‘’ placée au dessus de l’ouverture de la porte. Autrement , les portes doivent demeurer fermées durant le fonctionnement.
US ENVIRONMENTAL PROTECTION AGENCY



Veuillez vous référer au manuel d’instruction pour informations additionnels pour la conguration de
la ventilation.


     



          




352 Mountain House Road
Halifax, PA 17032
ECO:
PART # / REV: 3-90-00856_RevE
ORIGINATOR: Spidle
DATE: 04/15
LABEL SIZE: 11.5 in. x 6.5 in.
LOCATION: Rear of Stove
CLASS:
ADHESIVE: 468
MATERIAL: METAL
INK: BLACK
OVERCOAT:
LABEL TICKET
(4) Hole Size = .187
Corners .062

Room Heater Solid Fuel Burning Type
SUITABLE FOR MOBILE-HOME INSTALLATION 
135-S-29-2
 UL 1482-2011, UL 737-2011, ULC-S627-00, EPA Method 28 & 5G
Approved For Use in Mobile/Manufactured Homes (UM) 84-HUD - USA ONLY
Install and use only in accordance with manufacturer’s installation
and operation instructions and local codes. In absence of local codes, installation must meet
minimum requirements of NFPA 211 in USA. Refer to manufacturer’s instructions and local codes
for precautions required for passing chimney through a combustible wall or ceiling.
This wood heater needs periodic inspection and repair for proper operation. Consult the owner’s
manual for further information. It is against federal regulations to operate this wood heater in a
manner inconsistent with the operating instructions in the owner’s manual.
 (US Only) Do not install appliance in a sleeping
room. An outside air inlet must be provided. The structural integrity of the manufactured home’s
oor, walls, and ceiling must be maintained.
Flue connector pipe must be 6” diameter, minimum 24 MSG blue steel. Chimney must be factory
built 103HT or masonry construction. Contact Local Building or Fire Ofcials about restrictions and
installation inspection in your area.


EPA Certied Emissions: 2.6 g/hr
Fuel Type: Cord Wood

Optional Blower Harman #1-00-856002: Electrical Rating 115 VAC, 60Hz, 1AMP Maximum

OPERATE ONLY wITh dOORS CLOSEd
Replace glass only with 5mm ceramic, available from your dealer.
Combustible ooring must be protected with an approved 0.45R hearth board.
Appliance must be installed with the legs attached. Do not obstruct airow under the appliance.
      



      





2015 2016 2017 JAN FEB MAR APR MAY JUN JUL AUG SEP OCT NOV DEC

A = Unit to Sidewall 14”
 = Unit to Backwall 13”
C = Chimney Connector to Sidewall 24”
d = Chimney Connector to Backwall 18”
E = Unit to Adjacent Wall 16”
F = Chimney Connector to Adjacent Wall 22-1/2”

A = Entre le mur lateral et l’appareil 356mm
 = Entre le mur arriereet l’appareil 330mm
C = Entre le tuyau et le mur lateral 610mm
d = Entre le tuyau et le mur arriere 457mm
E = Entre le mur adjacent et l’appareil 406mm
F = Entre le tuyau et le mur adjacent 571mm

Maisons approuvé pour utilisation à Mobile / manufacturés (UM) 84-HUD - USA SEULEMENT
   Installer et utiliser uniquement en conformité avec installation et
d'utilisation les instructions du fabricant et les codes locaux. En l'absence de codes locaux, l'installation doit
satisfaire aux exigences minimales de la norme NFPA 211 aux Etats-Unis. Reportez-vous aux instructions
du fabricant et les codes locaux pour les précautions nécessaires pour faire passer la cheminée à travers
un mur ou un plafond combustible.
Ce poêle à bois doit inspection périodique et la réparation pour un fonctionnement correct. Consultez le
manuel du propriétaire pour plus d'informations. Ce est contre les règlements fédéraux pour faire fonctionner
ce poêle à bois d'une manière incompatible avec les instructions d'utilisation dans le manuel du propriétaire.
  (États-Unis uniquement) Ne pas installer l'appareil
dans une chambre à coucher. Une entrée d'air extérieur doit être fournie. L'intégrité structurale du sol, les
murs et le plafond de la maison préfabriquée doit être maintenue.
Tuyau de raccordement de fumée doit être de 6 "de diamètre, en acier au minimum 24 MSG bleu.
Cheminée doit être construite l'usine 103HT ou la construction de maçonnerie. Contactez Immeuble Local
ou fonctionnaires incendie au sujet des restrictions et l'inspection d'installation dans votre région.


Émissions certiés EPA: 2,63 g / h
Type de carburant: Cordon bois

Facultatif Blower Harman # 1-00-856002: Note électrique 115 VAC, 60Hz, 1AMP maximum


Remplacer le verre seulement avec de la céramique 5mm, disponible chez votre revendeur.
Plancher combustible doit être protégé par un conseil 0.45R foyer approuvé.
L'appareil doit être installé avec les jambes attachées. Ne pas obstruer le ux d'air sous l'appareil.


          

           
           




d
C
A
E
F
           

USA


CAN



ATTENTION:CHAUD LORS DU FONCTIONNEMENT- NE TOUCHEZ PAS
L’APPAREIL-GARDEZ LES ENFANTS ET LES VÊTEMENTS ÉLOIGNÉS- TOUT CONTACT
PEUT ENTRAÎNER DES BRÛLURES DE LA PEAU. RÉFÉREZ-VOUS À LA PLAQUE
SIGNALÉTIQUE ET AU MODE D’EMPLOI. GARDEZ LE MOBILIER ET LES AUTRES
MATÉRIAUX COMBUSTIBLES BIEN À L’ÉCART DE L’APPAREIL.
CAUTION:HOT wHILE IN OPERATION- DO NOT TOUCH-
kEEP CHILDRENAND CLOTHING AwAY- CONTACT MAY CAUSE SkIN
BURNS- SEE NAMEPLATE AND INSTRUCTIONS. kEEP FURNISHINGS
AND OTHER COMBUSTIBLE MATERIALS A CONSIDERABLE DISTANCE
AwAY FROM THE APPLIANCE
BARCODE LABEL
008

N
Hearth & Home Technologies welcomes you to our tradition of excellence! By choosing a Harman appliance, you have become
part of our commitment to meeting the heating needs of consumers with the most distinctive, powerful and responsible home
heating products available.
With it's compact, steel-body construction, the TL2.0 takes advantage of Harman’s 30+ years of stove design, technology and
manufacturing. The Firedome Plus secondary combustion system provides for super-clean burning and minimal maintenance.
The top-loading feature makes for more convenient loading, with enough fuel for an all day burn.
We wish you and your family many years of enjoyment in the warmth and comfort of your hearth appliance.
Thank you for choosing Harman.
This Label is located on the rear of the appliance. It contains important safety test information as well as the clearances to
combustible materials. The label also contains the appliance serial number. For your records, copy your serial number and
purchase date here.
Serial #: ________________________ Date of Purchase: ________________________
SAMPLE LABEL

3
Dry Seasoned Wood Only!
TL2.0 Woodburning Stove
Save These Instructions Harman® • TL2.0 Owner's Manual_R20 • 2011 -___ • 09/15

TABLE OF CONTENTS
This room heater must be connected to:
1. A chimney complying with the requirements for
Type HT chimneys in the standard for Chimneys,
Factory-Built, Residential Type and Building Heating
Appliance, UL 103
OR
2. A Code Approved Masonry Chimney with a Flue
Liner.
Section 1: Listing & Code Approvals
A. ApplianceCertications ........................... 4
B. Mobile Home Approval ............................4
C. GlassSpecications..............................4
D. Electrical Rating .................................4
E. BTU&EfciencySpecications ..................... 4
Section 2: Special Warning and Notes
A. Carbon Monoxide Warnings & Considerations .........5
Sections 3: Getting Started
A. Design, Installation & Location ......................6
B. Fire Safety .....................................6
C. Component Locator ..............................7
D. Pre-Use Checklist. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Section 4: Dimensions & Clearances
A. Appliance Dimensions ............................9
B. Clearances to Combustibles ......................10
C. Floor Protection ................................12
Section 5: Chimneys & Venting
A. Draft .........................................13
B. Chimney Connectors ............................13
C. Wall Pass-throughs .............................13
D. The Chimney ..................................14
Section 6: Mobile Home - (US Only)
A. Mobile Home Installation .........................20
Section 7: Appliance Set-Up
A. Outside Air Attachment...........................21
B. Leveling the Appliance ...........................21
C. Optional Cooking Grill ........................... 21
D. Optional Blower Kit..............................22
E. Top Air Grill Option ..............................22
F. Brushed Stainless Trim Option.....................22
Section 8: Operating Instructions
A. FuelSpecications .............................. 23
B. General Operating Information.....................23
C. Burning as a Fireplace ........................... 24
D. Combustion Process ............................24
E. User Controls ..................................25
F. Before Your First Fire ............................25
G. Building and Maintaining a Fire ....................25
Section 9: Service & Maintenance
A. Soot Formation.................................27
B. General Maintenance Procedures .................. 28
Section 10: Reference Materials
A. Wiring Diagram (Optional Blower) ..................30
B. Service Parts Listings............................31
C. Warranty Policy ................................35
= Contains updated information



4
TL2.0 Woodburning Stove
Dry Seasoned Wood Only! Save These InstructionsHarman® • TL2.0 Owner's Manual_R20 • 2011 -___ • 09/15
A. Appliance Certication E. BTU & Efciency Specications
1 Listing and Code Approvals
B. Mobile Home Approved
This appliance is approved for Installation in mobile/
manufactured homes in the US only. The structural
integrity of the mobile home oor, ceiling and walls must
be maintained. The appliance must be properly grounded
to the frame of the mobile home using a minimum of 8
AWG copper solid or stranded, insulated or bare wire or
equivalent. The unit must never be installed in a room
designated for sleeping. The unit must have provisions for
an outside air source when installed in a mobile home.
C. Glass Specications
This appliance is equipped with 5mm ceramic glass.
Replace glass only with 5mm ceramic glass. Please contact
your dealer for replacement glass if needed.
D. Electrical Rating
Optional Blower: 115 VAC, 60 Hz. <1 Amps
The TL2.0 Woodburning Stove is Certied
to comply with 2015 particulate emission
standards. Not approved for sale after May
15, 2020.
MODEL: TL2.0 Woodburning Stove
LABORATORY: OMNI Test Laboratories, Inc
REPORT NO. 135-S-29-2
TYPE: Solid Fuel Room Heater / Wood
Burning Type
STANDARD(s): UL1482-11, UL737-11 & ULC S627-
00, EPA Method 28 & 5G
ELECTRICAL
RATING:
115 VAC, 60 Hz
EPA Certication Number: 860
EPA Certied Emissions: 3.7 g/hr
*LHV Tested Efciency: 75.8%
**HHV Tested Efciency: 70.9%
***EPA BTU Output: 9,600 - 31,800
****BTU Input 55,300
Vent Size: 6 Inch
Recommend Log Lenght: 18" Maximum
Fuel Seasoned Cord Wood
* Weighted average LHV efciency using data collected
during EPA emissions test.
**Weighted average HHV efciency using data collected
during EPA emissions test.
***A range of BTU outputs based on EPA Default Efciency
and the burn rates from the low and high EPA tests.
****Based on the maximum burn rate multiplied by
approximately 8600 BTU’s which is the average BTU’s per
pound of wood with an average moisture content of 20%.
This wood heater needs periodic inspection and repair for
proper operation. It is against federal regulations to operate
this wood heater in a manner inconsistent with operating
instructions in this manual.

5
Dry Seasoned Wood Only!
TL2.0 Woodburning Stove
Save These Instructions Harman® • TL2.0 Owner's Manual_R20 • 2011 -___ • 09/15
2 Special Warnings and Notes
NOTICE
Due to ash buildup, it is strongly recommended to
have your stove professionally cleaned and serviced
annually. This includes all parts of the stove, and the
venting system.
Installation and repair of this stove should be done
by a qualied service person. We recommend that the
stove be inspected before use and at least annually
by a qualied service person. Periodic cleaning is
required throughout the heating season and at the
end of each winter for the stove to work efciently.
Carbon monoxide, referred to as CO, is a colorless, odorless
gas that is produced during combustion of wood and other
fuels. CO fumes are toxic and can be fatal.
The TL2.0 is a natural draft system which relies on a properly
designed chimney to remove CO and other combustion by-
products from the stove.
Even though this stove is designed to be as safe as possible,
it is important that you install a CO detector. This is true for
oil, gas, or coal burning products as well.
COisnotspecicallyheavierorlighterthanair.Therefore,
it is best to install the detector at table top level rather than
on the ceiling like a smoke detector.
CO detectors are very sensitive and may sound an alarm
for fumes other than CO or CO from sources other than the
stove such as car or lawn mower exhaust.
If the alarm sounds
1. Increase ventilation by opening windows or doors.
2. Make sure the stove doors and lid are closed and latched.
3.Checkstoveforsmokingorpufngcondition.Openby-
passandincreaseair-owtorebox,ifneeded.
4. Check chimney for possible blockage or down-draft.
5. Check for false alarm.
SAFETY NOTICE: IF THISAPPLIANCE IS NOT PROPERLY
INSTALLED, OPERATED AND MAINTAINED, A HOUSE
FIRE MAY RESULT. FOR YOUR SAFETY, FOLLOW
INSTALLATION DIRECTIONS. CONTACT LOCAL
BUILDING OR FIRE OFFICIALS ABOUT RESTRICTIONS
AND INSTALLATION INSPECTION REQUIREMENTS IN
YOUR AREA.
WARNING
!
THIS WOOD HEATER HAS A MANUFACTURER-SET
MINIMUM LOW BURN RATE THAT MUST NOT BE
ALTERED. IT IS AGAINST FEDERAL REGULATIONS
TO ALTER THIS SETTING OR OTHERWISE OPERATE
THIS WOOD HEATER IN A MANNER INCONSISTENT
WITH OPERATING INSTRUCTIONS IN THIS MANUAL.
BURNING COLORED PAPER, CARDBOARD,
SOLVENTS, TRASH AND GARBAGE OR ALTERING
THE STOVE FOR HIGHER HEAT OUTPUT MAY CAUSE
DAMAGE TO THE STOVE AND COULD RESULT IN
A HOUSE FIRE. USE ONLY APPROVED FUELS AND
FOLLOW ONLY THESE OPERATION GUIDELINES.
WARNING
!
NEVER USE GASOLINE, LANTERN FUEL, KEROSENE,
CHARCOAL LIGHTER FLUID, OR SIMILAR LIQUIDS TO
START OR “FRESHEN UP” A FIRE IN THIS HEATER.
KEEP ALL SUCH LIQUIDS WELL AWAY FROM THE
HEATER WHILE IT IS IN USE.
WARNING
!
NEVER CONNECT THIS UNIT TO A CHIMNEY FLUE
SERVING ANOTHER APPLIANCE.
WARNING
!
DO NOT CONNECT TO ANY AIR DISTRIBUTION DUCT
OR SYSTEM.
WARNING
!
WHEN THIS ROOM HEATER IS NOT PROPERLY
INSTALLED,AHOUSEFIREMAYRESULT.TOREDUCE
THE RISK OF FIRE, FOLLOW THE INSTALLATION
INSTRUCTIONS. CONTACT LOCAL BUILDING OR
FIRE OFFICIALS ABOUT RESTRICTIONS AND
INSTALLATION INSPECTION REQUIREMENTS IN
YOUR AREA.
CAUTION
!

6
TL2.0 Woodburning Stove
Dry Seasoned Wood Only! Save These InstructionsHarman® • TL2.0 Owner's Manual_R20 • 2011 -___ • 09/15
DO NOT CONNECT THIS UNIT TO A CHIMNEY FLUE
SERVICING ANOTHER APPLIANCE.
DO NOT CONNECT TOANYFORCED AIR DISTRIBUTION
DUCT OR SYSTEM.
B. Fire Safety
Maintain the designated clearances to combustibles.
Insulation must not touch the chimney. You must maintain
the designated air space around the chimney. This space
around a chimney is necessary to allow natural heat
removal from the area. Insulation in this space will cause
a heat buildup, which may ignite wood framing. NOTE:
Clearances may only be reduced by means approved
by the regulatory authority having jurisdiction.
To provide reasonable re safety, the following should be
given serious consideration:
1. Installatleastonesmokedetectoroneachoorofyour
home. Detectors should be located away from the heating
appliance and close to sleeping areas. Follow the smoke
detector manufacturer's placement and installation
instructions, and be sure to maintain regularly.
2. A conveniently located Class A re extinguisher to
contendwithsmallresresultingfromburningembers.
3. A practiced evacuation plan, consisting of at least two
escape routes.
4. Aplantodealwithachimneyreasfollows:
 Intheeventofachimneyre:
a. Evacuate the house immediately.
b. Notify Fire Department.
c. Never apply water to a suspected chimney re.
Serious damage could occur.
A.Design,Installation & LocationConsiderations
1. Appliance Location
Considerationmustbegiventosafety,convenience,trafc
ow,andthefactthattheappliancewillneedachimneyand
chimney connector. It is a good idea to plan your installation
on paper, using exact measurements for clearances and
oor protection, before actually beginning the installation.
When installing on a combustible oor, proper oor
protection material must be used. See page 12 for details.
Maintain specied vent clearance to combustible
requirements listed by the vent manufacturers instructions
and all clearance to combustibles listed in this manual.
Check with your local building code agency before you begin
your installation. Be sure local codes do not supersede UL
specications and always obtain the required permit so
thatinsuranceprotectionbenetscannotbeunexpectedly
cancelled. If any assistance is required during installation,
please contact your dealer.
Werecommendthataqualiedbuildinginspectorandyour
insurance company representative review your plans before
and after the installation.
Be sure to provide a source of fresh air to the room or
directly to the appliance. Make-up air is needed to replace
what the chimney draws away through the appliance.
Consider attaching outside air to the appliance. Certain
conditions can create negative pressure within the dwelling.
When this occurs, you may have trouble operating the wood
stove. Worse yet, it may be strong enough to allow smoke
leakage from the appliance. Installation on lower levels and
in basements can be especially affected.
3 Getting Started
CAUTION
!
FIRE HAZARD
DO NOT OPERATE APPLIANCE BEFORE
READING AND UNDERSTANDING THE
OPERATING INSTRUCTIONS.
FAILURE TO OPERATE PROPERLY MAY
CAUSE A HOUSE FIRE.
WARNING
!

7
Dry Seasoned Wood Only!
TL2.0 Woodburning Stove
Save These Instructions Harman® • TL2.0 Owner's Manual_R20 • 2011 -___ • 09/15
C. Component Locations
Top Load Opening
Air Control
Front Load Door
Top Load Door
Bypass Damper
Control Handle
Ash Door
Ash Door
Latch
Front Load
Door Latch
Bolt-Down Holes for Mobile
Home Installations

8
TL2.0 Woodburning Stove
Dry Seasoned Wood Only! Save These InstructionsHarman® • TL2.0 Owner's Manual_R20 • 2011 -___ • 09/15
D. Pre- Use Check List
INSPECT APPLIANCE AND COMPONENTS
FOR DAMAGE. DAMAGED PARTS MAY
IMPAIR SAFE OPERATION.
• DO NOT INSTALL DAMAGED
COMPONENTS.
• DO NOT INSTALL INCOMPLETE
COMPONENTS.
• DO NOT INSTALL SUBSTITUTE
COMPONENTS.
REPORT DAMAGED PARTS TO DEALER.
FIRE RISK.
HEARTH & HOME TECHNOLOGIES
DISCLAIMS ANY RESPONSIBILITY FOR,
AND THE WARRANTY WILL BE VOIDED
BY, THE FOLLOWING ACTIONS:
WARNING
!
WARNING
!
• INSTALLATION AND USE OF ANY DAMAGED
APPLIANCE.
• MODIFICATION OF THE APPLIANCE.
• INSTALLATION OTHER THAN AS INSTRUCTED
BY HEARTH & HOME TECHNOLOGIES.
• INSTALLATION OF PARTS OR COMPONENTS
NOT SUPPLIED OR APPROVED BY HEARTH &
HOME TECHNOLOGIES.
• OPERATING APPLIANCE WITHOUT THE LEGS
ATTACHED.
• OPERATING APPLIANCE WITHOUT FULLY
ASSEMBLING ALL COMPONENTS.
• DO NOT OVERFIRE.
OR ANY SUCH ACTION THAT MAY CAUSE A FIRE
HAZARD.
1. Placetheapplianceinalocationnearthenal
installation and follow the procedures below:
2. Open the appliance and remove all articles
packed inside. Inspect all items for shipping
damage. Notify dealer of any missing or
damaged goods.
3. All safety warnings have been read and
followed precisely.
4. This Owner's Manual has been read in it's
entirety.
5. Floor protection requirements have been read
and followed.
6. The ue connector has been installed in
accordance with the instructions herein.
7. The proper clearances from the appliance and
chimney connector to combustibles have been
met.
8. The masonry chimney has been cleaned and
inspected by a professional, or the factory built
metal chimney is installed according to the
manufacturers instructions.
9. The chimney meets the minimum height
requirements.
10. All labels and hang tags have been removed
from the glass.
11. All plated surfaces have been wiped clean, if
applicable.
12. The optional air distribution blower has been
installed properly.
13. A properly grounded electrical receptacle is
available within reach of the blower's power
cord (if installed).

9
Dry Seasoned Wood Only!
TL2.0 Woodburning Stove
Save These Instructions Harman® • TL2.0 Owner's Manual_R20 • 2011 -___ • 09/15
A. Appliance Dimensions
25-7/8"
(657mm)
26-7/8"
(665mm)
32-5/16"
(820mm)
35-5/16"
(897mm)
Air Intake
9-1/8"
(231mm)
4 Dimensions & Clearances
26"
(660mm)
9-5/8""
(243mm)

10
TL2.0 Woodburning Stove
Dry Seasoned Wood Only! Save These InstructionsHarman® • TL2.0 Owner's Manual_R20 • 2011 -___ • 09/15
B. Clearances To Combustibles
*D B
C
A
A
B
B
A
Vertical Venting Conguration
Location Single-Wall Pipe Double-Wall Pipe
AUnit to Side Wall 14" / 356mm 14" / 356mm
BUnit to Back Wall 13" / 330mm 7" / 178mm
CVent Pipe to Side Wall 24" / 640mm 24" / 610mm
DVent Pipe to Back Wall 18" / 457mm 12" / 305mm
Corner Installation
ECorner to Adjacent Wall 16" / 406mm 10" 254mm
FConnector to Wall 22-1/2" / 457mm 16-1/2" / 419mm
For clearance reduction methods, refer to NFPA 211 or Local Codes
Follow NFPA 211 Table 13.6.1 "Clearances for Solid Fuel–Burning Appliances" for clearance from the top of the
unit to ceiling.
This unit was not tested for installation into an Alcove. Follow NFPA 211 Table 13.6.1 "Clearances for Solid Fuel–
Burning Appliances".

11
Dry Seasoned Wood Only!
TL2.0 Woodburning Stove
Save These Instructions Harman® • TL2.0 Owner's Manual_R20 • 2011 -___ • 09/15
C
A
G
F
D
B
E
24" (610 mm)
Minimum vertical
prior to elbow.
Vertical Vent, Horizontal Exit
Location Single-Wall Pipe
AUnit to Side Wall 13" / 330mm
BUnit to Back Wall 13" / 330mm
CVent Pipe to Side Wall 23" / 584mm
DVent Pipe to Back Wall 18" / 457mm
EVent Pipe to Ceiling 16" / 406mm
Corner Installation
FCorner to Adjacent Wall 16" / 406mm
GConnector to Wall 22-1/2" / 571mm
For clearance reduction methods, refer to NFPA 211 or Local Codes
Follow NFPA 211 Table 13.6.1 "Clearances for Solid Fuel–Burning Appliances" for clearance from the top of the
unit to ceiling.
This unit was not tested for installation into an Alcove. Follow NFPA 211 Table 13.6.1 "Clearances for Solid Fuel–
Burning Appliances".

12
TL2.0 Woodburning Stove
Dry Seasoned Wood Only! Save These InstructionsHarman® • TL2.0 Owner's Manual_R20 • 2011 -___ • 09/15
C. Floor Protection Requirements
Floor Protection Requirements
If the appliance is being installed on a combustible oor,
non-combustible oor protection must be installed. In all
installations, the area under and around the stove must
be protected from falling ash and live coals. The area
under a horizontal run of chimney connector must also be
protected, extending two (2) inches (51mm) to each side of
the horizontal connector.
DO NOT BLOCK OR RESTRICT THE AIRFLOW UNDER
THE APPLIANCE.
Furtherguidelinesforoorprotectionareasfollows:Inthe
U.S.theoorprotectormustbecompletelyunderthestove,
and extending 18" in front of the door opening, 8" to each
side of the door opening, and 8" to the back.
InCanada,theoorprotectionmustextend18"(457mm)in
front of the door opening, and 8" (203mm) to each side of
the appliance, and to the rear.
MinimumSize oorprotection (USA)is 46-1/16"Deepby
32-1/2" Wide.
Floor protection touching the wall: 53-9/16" Deep x 32-1/2"
Wide.
JJ K
L
60”
60”
Interior Wall
Interior Wall
Minimum size oor protection for a corner installation hearth
pad is 46-5/8" x 32-1/2" (USA ONLY). NOTE: Floor protector
WILL NOT touch the wall. NOTE: Floor protector WILL NOT
touch the wall.
TypeIorTypeIIoorprotectioncanbeused.
*Floor protection dimensions for the front and sides are
measured from the appliance door opening in The United
States. In Canada, the side dimension is measured from the
widest part of the appliance.
Parallel versus Corner Installations
A parallel installation is one in which the back and sides of
the stove are parallel to the walls behind and to the side of
the stove. A corner installation is one in which the back of the
stove is positioned diagonally across a corner of the room.
Each installation requires its own set of clearances.
For corner installations, the required clearance distances
from the stove are:
1. to the side wall, 13" (330mm).
2.Fromtheueconnectortothewall,23"(584mm)
3. Horizontal pipe to the ceiling, 16"(406mm).
Note: For a vertical chimney connector in a parallel
installation the distance of the connector to the side wall
must be 23" (584mm), due to the required side clearance of
the stove itself. Fireplace installations must meet these same
clearancerequirements;specicallyfollowtheseguidelines
for mantel and trim clearances.
For corner installations, the clearance distances are 16"
(406mm) from each corner of the stove measured straight
back to the nearest combustible material, and 22-1/2"
(571mm) from the chimney connector to the walls. To stay
withintheseclearancesandhavetheoorprotectortouch
the interior wall it must be a hearth pad size of 60" x 60"
(USA ONLY).
Alternate oor protector dimension may be used as long as
they satisfy the measurement requirements shown above.
Floor Protection
Requirements US Canada
JSides 8" 203mm
KFront 18" 457mm
LRear 8" 203mm

13
Dry Seasoned Wood Only!
TL2.0 Woodburning Stove
Save These Instructions Harman® • TL2.0 Owner's Manual_R20 • 2011 -___ • 09/15
5 Chimneys & Venting
A. Draft
Draft is widely misunderstood. It is important that you, the
stove operator, realize that draft is a variable effect, not a
given quantity. Stoves and chimneys do not have draft, yet
draft is the key to your stove’s performance.
Draft is a force, produced by an operating stove and the
chimney to which it is attached. It is created by hot gases
rising up the chimney, creating a pressure difference between
the inside of your home and the outside air. It continually
moves fresh combustion air into the stove, and hot exhaust
gasesout ofthestove; withoutthisconstant ow,the re
will go out.
Other factors, such as barometric pressure, winds, the
airtightness of the home, the total inside chimney volume,
chimney height and the presence of venting devices such
as exhaust fans also play a role in maintaining an adequate
draft. Low barometric pressures, super insulated homes
and exhaust fans can reduce draft; winds can play havoc
with draft; and too large or too small a chimney volume can
cause reduced draft due to the excessive cooling or not
enough room to vent exhaust gases. Introducing outside air
directly to the stove may help remedy a low draft problem.
Somesignsofinadequatedraftaresmoking,odor,difculty
inmaintainingthere,andlowheatoutput.Overdraftcanbe
caused by a very tall chimney even if it is the recommended
size, and can cause overring of your stove. Signs of an
overdraft include rapid fuel consumption, inability to slow
there,andpartsofthestoveorchimneyconnectorglowing
red. It is important that you follow the chimney guidelines in
this manual, including size, type, and height to avoid draft
problems.
When installed and operated according to this manual, the
stove will produce enough hot gases to keep the chimney
warm so that adequate draft is maintained throughout the
burn cycle.
B. Chimney Connectors
In general, following these guidelines will ensure compliance
with all national and provincial codes; prior to beginning your
installation, check with your local building code ofcial to
checkon additionallocalregulations whichmayinuence
the design and placement of your venting system.
The Harman TL2.0 may be installed with a minimum (.6mm)
24 gauge blue or black steel, chimney connector pipe. The
sizeoftheconnectorshouldcorrespondtothesizeoftheue
collar opening, which is 6" (152mm). Do not use makeshift
compromises. No part of the chimney connector may pass
through an attic or roof space, closet or other concealed
space, or through a oor or ceiling. Whenever possible,
avoid passing the connector through a combustible wall; if
you must, use an approved wall pass-through, described
later in this section.
Assembletheconnectorbeginningattheuecollar,withthe
crimped ends pointing towards the stove (to keep debris or
residue inside the system). Each joint, including the one to the
stove’suecollarandtheonetothechimneyitselfshouldbe
secured with at least three sheet metal screws. Screws may
be a maximum of 3 inches apart. A 1-1/4" (30mm) overlap is
requiredateachjoint,includingtheuecollarattachment.
No more than two 90° elbows should be used, and the total
length of connector should not exceed 10 feet (3m). All
horizontal runs of connector must have a minimum upward
slope of 1/4" per foot (20mm per meter).
C. Wall Pass-throughs
Depending on your local building codes, and the pertinent
provincial or national codes, there are several choices for
passing the chimney connector safely through a wall. Before
beginningyourinstallation,contactlocalofcials,andalso
thechimneyconnectorandchimneymanufacturerforspecic
requirements.
Canada. Three methods are approved by the Canadian
Standards Association. The diagram on the next page shows
one method requiring an 18" (450mm) air space between the
connector and the wall. It allows use of one or two covers
as described in the diagram. The two other methods are
described in detail in the current issue of CAN/CSA B365,
the national standard.
United States In the U.S., the national code is NFPA 211.
While many localities adopt this standard, be sure to check
with local authorities before beginning your installation.
The NFPA (National Fire Protection Agency) permits four
methods for passing through a combustible wall. A commonly
used method to pass through a wall directly to a masonry
chimney is to clear a minimum 12" (300mm) around the
entirechimneyconnector,andllitwithbrickmasonrywhich
isatleast3-1/2"(90mm)thick.Areclayliner,minimum3/8"
(9mm) wall thickness must run through the brick wall to the
chimney liner (but not beyond the inner surface of the liner).
It must be cemented in place with refractory cement. This
method is illustrated on the next page. For details on the
other three options, refer to the most recent edition of the
NFPA 211 code.
The Chimney Connector Shall Not Pass Through an Attic or Roof Space,
Closet or Similar Concealed Space, a Floor or Ceiling.

14
TL2.0 Woodburning Stove
Dry Seasoned Wood Only! Save These InstructionsHarman® • TL2.0 Owner's Manual_R20 • 2011 -___ • 09/15
D. The Chimney
This unit must be installed into a chimney approved for use
with solid-fuel appliances. In the U.S., it must be connected to
(1) a prefabricated chimney complying with the requirements
for Type HT chimneys in the Standard for Chimneys, Factory-
Built, Residential Type and Building Heating Appliances, UL
103,or(2)acode-approvedmasonrychimneywithaue
liner.
In Canada, this unit is listed for use with prefabricated
chimneys tested and listed to the high temperature (650°C)
chimney standard, ULC S-629, or with a code approved
masonry chimney.
For mobile homes, (US only) it must only be installed with
a factory built stainless steel chimney. The chimney system
should include all required installation components, such as
vaporbarriersandroofashing,astestedforuseinmobile
homes.
The minimum recommended height for any chimney is 16
ft. (4.8m) above ue collar height. For non-mobile home
installations, a round flue (either masonry or approved
prefabricated), of either 6" (150mm), 7" (180mm) or 8"
(200mm) may be used. For square or rectangular masonry
chimneys, nominal sizes of 8" x 8" or 7" x 12" (200mm x 200
mm, 180mm x 300mm) may be used.
Codes require that solid-fuel chimneys extend 3 ft. (0.9m)
above the highest point at which they exit from the roof. Then,
the chimney must extend 2 ft. (0.6m) above the highest point
within a 10ft (3m) radius. Thus, the 3 foot, 2 foot, 10 foot rule:
3ft. - Above roof exit point
2ft. - Higher than anything within-
10ft. of the chimney.
The restriction of not venting more than one appliance to
thesameueappliestotheU.S. specically.Whileitisnot
recommended that you use the same chimney for more than
one appliance, in Canada certain exceptions may be made.
Besuretocontactyourbuildingcodeinspectionofcialto
seeifthisoptionisallowedinyourarea,andtondoutthe
specicrequirementsforsuchaninstallation.
DO NOT CONNECT THIS UNIT TO A CHIMNEY FLUE
SERVING ANOTHER APPLIANCE.
Hole with minimum
clearance of 18”
(450mm) Between
connector and wall.
Non-combustible cover, one
side only. If two covers are
used, each must be mounted
on non-combustible spacers
at least 7/8” (21mm) away
from the wall.
1” (25mm)
Clearance
AN APPROVED CANADIAN WALL PASS-THROUGH
AN APPROVED U.S. WALL PASS-THROUGH
Minimum 2” (50mm)
Clearance to Brick
Liner Minimum 12”
(50mm) to Brick
Fire Clay
Thimble
Chimney
Connector
Chimney Flue
Masonry Chimney Built to
NFPA 211 Specifications
Closest Combustible Material
Minimum 12” (300) to
Combustibles
AN APPROVED CANADIAN WALL PASS-THROUGH AN APPROVED U.S. WALL PASS-THROUGH
More than 10 Ft. (3 m)
10 Ft. (3 m)
2 Ft. (.6 m) Min
Height necessary
above any roof surface
within 10 Ft. (3 m)
3 Ft. (.9 m) minimum
above exit point
Ridge
Chimney
THE 3-FOOT, 2-FOOT, 10 FOOT RULE

15
Dry Seasoned Wood Only!
TL2.0 Woodburning Stove
Save These Instructions Harman® • TL2.0 Owner's Manual_R20 • 2011 -___ • 09/15
Existing Masonry Chimneys
If you plan on using a pre-existing masonry chimney, have
it thoroughly inspected and cleaned. Any faults which make
the chimney unsafe and unusable must be repaired prior to
use. These can include improper height, structural defects,
blockages, inadequate clearance to combustibles, unsealed
openings into other rooms of the house, signs of creosote or
smoke leakage, a loose or absent clean-out door, or absence
of a liner.
Venting to a Masonry Chimney
When connecting to a masonry chimney, several provisions
are standard. First, whether the chimney connector is vented
to the chimney through a thimble or a breech pipe, neither
must pass beyond the inner surface of the chimney liner,
andbothmustbermlycementedinplacewithrefractory
cement. (A thimble is a masonry pipe which is inserted
through the chimney wall, and is frequently the preferred
method; a breech pipe is a piece of steel pipe used the same
way.) In Canada, a breech pipe has ridges or protrusions to
lockitrmlyintotherefractorycement.Ineithercase,the
chimney connector vents to the chimney through the thimble
or breech pipe.
Using a thimble, the connector slides completely inside the
masonrytotheinneredgeoftheueliner,andmaybeeasily
removed for chimney and connector inspection. A breech
pipe must extend at least 2" (50mm) into the room, so the
connector can be attached with sheetmetal screws.
Venting to a Masonry Fireplace Chimney
In some situations, a code compliant chimney originally
usedforamasonryreplacemaybeused.Inadditiontothe
requirements found in the previous paragraphs, it is important
to be aware that all clearances must be met, including those
from the chimney connector to combustibles. Do not forget to
includeoorprotectioninyourplans.(SeeClearancesand
FloorProtectioninthissection.)Sincemanyreplaceshave
exposed wooden mantels and trim, pay special attention to
the clearances necessary to these materials.
Ifyourreplacechimneyisbehindacombustiblewall,you
must use an approved wall pass-through system to gain
access to the masonry chimney. The chimney connector
must enter the chimney at a place where it is lined, and
thereplacemust bemade inoperable.Forexample,you
might remove the damper, replacing it with a secure, airtight,
noncombustible seal (removable for inspection); this also
satisestherequirementthatnoroomairmustbeallowed
to enter the chimney.
Installing to a Prefabricated Chimney
When venting using a prefabricated chimney, be sure
to contact local building code authorities, and to follow
the manufacturer’s instructions exactly. Use only the
manufacturer’s parts; do not use makeshift installation
techniques. All prefabricated chimneys must be tested to
either the U.S. or Canadian high-temperature standards, UL
103 or ULC S629.
Other Considerations
Do not burn any fuel other than dry cordwood. Never use
highly volatile substances in your stove, such as gasoline,
which could cause an explosion.
When solid fuels are burned completely, they produce
water and carbon dioxide. However, in long slow burns, a
substantial amount of carbon monoxide may be produced.
If allowed to build up, carbon monoxide (which is odorless)
can prove fatally poisonous. Proper ventilation and draft will
prevent this from happening. If you smell smoke, thoroughly
ventilate your dwelling, and contact your dealer for service.
Other causes of poor ventilation or draft are icing, exhaust
fans, a blocked outside air inlet, and room air starvation. If
your stove is sluggish and you get occasional odor, check
thesepossibilitiesandincreasetheairowinyourhome.
The Chimney and connector must be maintained in good
condition and kept clean.
Chimney
Connector
Clay thimble, reaching
just to the inside of the
chimney liner
Mechanical fasteners
(minimum 3) but not at the
bottom of the connector
Chimney liner
inner edges
High-temperature
sealant used to cement
the clay thimble

16
TL2.0 Woodburning Stove
Dry Seasoned Wood Only! Save These InstructionsHarman® • TL2.0 Owner's Manual_R20 • 2011 -___ • 09/15
Standard Ceiling Installation with Factory Built Chimney
The Chimney Connector Shall Not Pass Through an Attic or Roof
Space, Closet or Similar Concealed Space, a Floor or Ceiling.
Chimney Connector
Minimum air space
with chimney listing
Chimney support
Attic radiation shield
Chimney sections
Chimney cap
Storm collar
Roof flashing
Roof radiation
shield
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
SS
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S

17
Dry Seasoned Wood Only!
TL2.0 Woodburning Stove
Save These Instructions Harman® • TL2.0 Owner's Manual_R20 • 2011 -___ • 09/15
Chimney Connector
Cathedral style
chimney support
Finishing collar
Roof radiation shield
Chimney cap
Sealed storm
collar
Roof flashing
Factory-Built metal
chimney
Cathedral Ceiling Installation with Factory Built Chimney

18
TL2.0 Woodburning Stove
Dry Seasoned Wood Only! Save These InstructionsHarman® • TL2.0 Owner's Manual_R20 • 2011 -___ • 09/15
Chimney Breach Fireplace Conversion with Non-Combustible Wall
The Chimney Connector Shall Not Pass Through an Attic or Roof Space, Closet or Similar Concealed Space, a
Floor or Ceiling.
Minimum clearance to
unprotected ceiling 15”
Chimney connector
sealed at thimble
Flue liner with required air space
Minimum of three sheet
metal screws per joint of
chimney connector
Mantel and trim protection
Airtight
insulated
clean-out
Damper closed
and sealed with
non-combustible
material
Combustible Floor
Floor Protection*
*Floor protection in accordance with Solid Fuel Appliance Listing

19
Dry Seasoned Wood Only!
TL2.0 Woodburning Stove
Save These Instructions Harman® • TL2.0 Owner's Manual_R20 • 2011 -___ • 09/15
Chimney Breach Fireplace Conversion with Combustible Wall
* Floor Protection in Accordance with Solid Fuel Appliance Listing
** Check with your local building codes for clearance.
The Chimney Connector Shall Not Pass Through an Attic or Roof Space, Closet or Similar Concealed Space, a
Floor or Ceiling.
Minimum clearance from chimney
connector to uprotected ceiling 15”
Flue liner with required
air space
Listed or approved thimble assembly
1” Clearance for exterior chimney or
2” clearance for interior chimney and
2” clearance for NFPA 211 - type
approved thimbles
Airtight
insulated
clean-out
Damper closed
and sealed with
non-combustible
material
Combustible Floor
Floor Protection*
* Floor protection in accordance with Solid Fuel Appliance Listing
** Check with your local building codes inspector for clearance.
Combustible
Wall
Sheet
Rock
Mantel and Trim Protection

20
TL2.0 Woodburning Stove
Dry Seasoned Wood Only! Save These InstructionsHarman® • TL2.0 Owner's Manual_R20 • 2011 -___ • 09/15
A. Mobile Home Installation
Mobile home approval - U.S. only.
DO NOT INSTALL IN A MOBILE HOME IN CANADA.
1. An outside air inlet must be provided for combustion
air, and must remain clear of leaves, debris, ice, and/or
snow. The outside air path must be unrestricted while
the appliance is in operation. Use Kit #1-10-856082 to
attach to unit.
2. The combustion air intake system must be of metal
construction. It must permit zero-clearance to
combustible materials, and contain a rodent screen.
3. The appliance must be secured to the mobile home
structure by bolting it to the oor. There are holes
provided in the pedestal base. Secure with the proper
length lag bolts, through the hearth pad and into the
homeoor.
4. The appliance must be grounded to the metal framing
of the mobile home
5. All clearances to combustibles and oor protection
requirements must be followed.
6. Follow the vent manufacturer's instructions when
installing in a mobile home. Must be connected to a
UL103 HT ventilated chimney connector, UL103 HT
chimney, and terminal cap with spark arrestor.
7. Use silicone to create an effective vapor barrier at
the location where the chimney or other component
penetrates to the exterior.
8. Installation shall be in accordance with the Manufactured
Home and Safety Standard (HUD) CFR 3280, Part 24
9. The appliance must never be installed in a room
designated for sleeping.
10. Burn wood only. Other fuels may generate poisonous
gases (carbon monoxide).
11. If unit burns poorly while an exhaust blower (range
hood) is operating, increase the supply of combustion
air to the appliance
Note: The top sections of the chimney must be removable
to allow a maximum clearance of 13-1/2 feet (343mm) from
ground level for transportation purposes.
6 Mobile Home
THE STRUCTURAL INTEGRITY OF THE MOBILE HOME
FLOOR, WALLAND CEILING/ROOF MUST BE MAINTAINED.
DO NOT CUT THROUGH:
• FLOOR JOIST, WALL STUDS, OR CEILING TRUSSES.
• ANY SUPPORTING MATERIAL THAT WOULD AFFECT
THE STRUCTURAL INTEGRITY.
CAUTION
!
INSTALLATION MUST COMPLY WITH
MANUFACTURED HOME AND SAFETY STANDARD
(HUD), CFR 3280, PART 24.
WARNING
!
DO NOT INSTALL IN SLEEPING ROOM.
WARNING
!
Chimney Connector
Minimum air space
with chimney listing
Chimney support
Attic radiation shield
Chimney sections
Chimney cap
Storm collar
Roof flashing
Roof radiation
shield
Outside
Air
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
SS
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S