Hathaway NG2015 User manual

8' HOT SHOT SKEEBALL TABLE
ASSEMBLY INSTRUCTIONS
NG2015

THANK YOU!
Thank you for purchasing this product.
We work around the clock and around the globe to ensure that our products
maintain the highest possible quality. However, in the rare instance that your
product is defective or missing parts, contact your retailer, or call 800-759-0977,
to submit parts requests or warranty claims. Please read the warranty
information at the back of these assembly instructions for further details.
IMPORTANT! PLEASE READ THESE ASSEMBLY INSTRUCTIONS IN
ENTIRETY BEFORE ASSEMBLING YOUR PRODUCT.
2

PARTS IDENTIFIER (NOT TO SCALE)
3
H1 - 1-1/4” Screw (36) H2 - 5/16” x 1-1/8”
Bolt (12)
H3 - 5/16” Washer (12) H4 - 1/4” x 1-1/4”
Bolt (4)
H5 - 1/4” x 1” Bolt (4) H6 - 1/4” Washer (4) H7 - 1/4” Washer (8) H8 - 3/4” Screw (3)
H9 - 3/8” Screw (4) H10 - 1-1/4” Flat Screw (6) H11 - 1-1/2” Screw (3) H12 - 3/4” Flat Screw (4)
T1 - Allen Wrench (1)
P1L - Left Front Leg (1) P1R - Right Front Leg (1) P2L - Left Middle Leg (1) P2R - Right Middle Leg (1)
P3R - Right Back Leg (1)P3L - Left Back Leg (1)
P6L - Left Front
Side Apron (1)
P6R - Right Front
Side Apron (1)
P7L - Left Back
Side Apron (1)
P7R - Right Back
Side Apron (1)
P4 - Spreader (3) P5 - Front End Apron (1)

PARTS IDENTIFIER (NOT TO SCALE)
4
P13 - Back
Board (1)
P14 - Electronic
Scorer (1)
P15 - Target
Board (1) P16 - Connect Hinge Set (2) P17 - Net (1)
P12 - Back Bottom
Panel (1)
P11 - Back Upper
Panel (1)
P9 - Front
Top Panel (1)
P10 - Front
Bottom Panel (1)
A1 - Ball (6)
P21A - Support
Panel (1)
P18 - Net Frame Front (1)
P19 - Net Frame Back (1)
Larger
Smaller
(Attaches to Side Apron)
P20 - Net Spacer Bar (2)
P8A - Crossbeam (1) P8B - Crossbeam (2)
P21B - Support
Panel (1)
P22 - “L”Support Panel (1) P23 - Cover Panel (1)
Please see Parts List at end of manual for part number when ordering parts.
For replacement parts please call 800-759-0977.
(Attaches to Side Apron)

ASSEMBLY TIPS
5
1. Find a clean, level surface to begin the assembly of your game table. The table will be
partially assembled upside down and then turned over onto its legs. This is a heavy game
and turning it over will require at least two strong adults.
2. Remove all of the contents from box and verify that you have all of the parts shown on
Note: Some parts may be pre-installed
or pre-assembled.
understand the text before beginning each assembly step.
4. When installing parts that have more than one screw or bolt, hand tighten all
5. Electric screwdrivers may be helpful during assembly; however, please set a low torque
and use extreme caution because screws may be stripped or overtightened, resulting in
damaged parts, if the electric screwdriver’s torque is set too high.
WARNINGS!
READ AND FOLLOW ALL ASSEMBLY, OPERATION AND SAFETYINSTRUCTIONS CAREFULLY.
CHOKE HAZARD - THIS TABLE CONTAINS SMALL BALLS AND PARTS
NOT SUITABLE FOR CHILDREN UNDER 3 YEARS OF AGE.

ASSEMBLY INSTRUCTIONS
6
Unfinished Side Up
Black Side Down
P10
H8
P21B
Figure 1
1. Find a clean, level place to begin the assembly of your game. We recommend building the unit on the shipping carton to
protect the parts during assembly. Note: The two main units are assembled upside down then turned over for final assembly.
2. Attach the SUPPORT PANEL, P21B, to the FRONT BOTTOM PANEL, P10, using (2) SCREWS, H8, through the two
outer holes as shown in Figure 1. The middle hole will be used in a later step. Note: The P10 panel and P21B support
panel both have pre-drilled holes for screws.
3. Place the LEFT FRONT SIDE APRON, P6L, and RIGHT FRONT SIDE APRON, P6R, upside down and approx. 2 feet
apart, as shown in Figure 2.
4. Insert FRONT TOP PANEL, P9, with finished white side down, into lower grooves of SIDE APRONS, P6L and P6R.
Make sure the end of P9 with the cutouts is on the same end as gear hinge as shown in Figure 2. Slide P9 forward until
the end with cutouts is flush with SIDE APRON ends above gear hinges. With help from another adult, hold this assembly
firmly and attach pieces together using (2) SCREWS, H1, and pre-drilled holes on each side.
5. Attach FRONT END APRON, P5, with groove facing in, using (2) SCREWS, H1, and pre-drilled holes on each side.
Note: Don’t tighten screws all the way until you complete Step 6. This will make it easier to get P10 into P5 groove.
6. Insert FRONT BOTTOM PANEL, P10, with unfinished side up, into upper grooves of SIDE APRONS, P6L and P6R.
Slide P10 forward until the end is flush with SIDE APRON ends above gear hinges, even with panel P9. Tighten P5 Screws.
Note: This unit is assembled
upside down.
P5
H1
H1
P6L
Note: Location
of gear hinge
P6R
Note: Location
of gear hinge
Note: Location
of these cutouts
P10
P9
Unfinished
Side Up Slide both
panels in grooves
White
Side Down
Figure 2

7. Attach CROSSBEAM, P8B, with cutout opening facing down and to the left, using (2) SCREWS, H1, and pre-drilled
holes on each side. Use (1) SCREW, H11, to attach center of crossbeam through P10 and into P21B, as shown in Figure 3.
8. Attach LEFT and RIGHT FRONT LEGS, P1L and P1R, using (2) BOLTS, H2, and (2) WASHERS, H3, on each leg, as
shown in Figure 3. Note: Hand tighten for now, and then do final tightening with ALLEN WRENCH, T1, once P4 Spreader
is attached in next step.
9. Attach SPREADER, P4, using (4) SCREWS, H1, as shown in figure 3. Note: Hand place screws in all four pre-drilled
holes to align panel before tightening.
CAUTION:
P4 SPREADER MUST BE CENTERED
CORRECTLY ONTO PRE-DRILLED HOLES
IN LEGS BEFORE ATTACHING WITH H1
SCREWS.
Figure 3
NOTE: Location
of gear hinge
H1
H1
H1
H2
H3
H11
P4
P8B
P1L
P1R
ASSEMBLY INSTRUCTIONS (CONT.)
7

10. Attach the SUPPORT PANEL, P21A, to the FRONT BOTTOM PANEL, P10, using (1) SCREW, H8, through the
center hole as shown in Figure 4. The outer two holes will be used in a later step. Note: The P12 panel and P21A support
panel both have pre-drilled holes for screws.
Unfinished Side Up
Black Side Down
P12
H8
P21A
Figure 4
11. Place the LEFT BACK SIDE APRON, P7L, and RIGHT BACK SIDE APRON, P7R, upside down and approx. 2 feet
apart, as shown in Figure 5.
12. Insert BACK TOP PANEL, P11, with finished white side down, into lower grooves of SIDE APRONS, P7L and P7R.
Make sure the end of P11 with the cutouts is on the same end as gear hinge as shown in Figure 5. Slide P11 forward until
the end with cutout is flush with SIDE APRON ends above gear hinges. With help from another adult, hold this assembly
firmly and attach pieces together using (3) SCREWS, H1, and pre-drilled holes on each side.
13. Insert BACK BOTTOM PANEL, P12, with unfinished side up, into upper grooves of SIDE APRONS, P7L and P7R.
Slide P12 forward until the end is flush with SIDE APRON ends above gear hinges, even with panel P11.
Note: This unit is assembled
upside down.
P12
H1
H1
P7L
Note: Location
of gear hinge
P7R
Note: Location
of these cutouts
P11
Unfinished
Side Up
Slide both
panels in grooves
White
Side Down
Figure 5
THANK YOU!ASSEMBLY INSTRUCTIONS (CONT.)
8

Figure 6
P4
P2L
P2R
Note: Correct location
of Support Panel to Legs
14. Attach CROSSBEAMS, P8A and P8B, with cutout openings facing down and to the right, using (2) SCREWS, H1, and
pre-drilled holes on each side. Use (1) SCREW, H11, to attach center of CROSSBEAM, P8B, through P12 and into P21A,
assembled in Step 10. Note: Cutouts used as wiring guides in future step. See Figure 6 for correct locations of P8A and P8B.
15. Assemble LEFT and RIGHT MIDDLE LEGS, P2L and P2R, together with SPREADER, P4, using (4) SCREWS, H1,
as shown in Figure 6. Note: Hand place screws in all four pre-drilled holes to align panel before tightening. Attach “L”
SUPPORT PANEL, P22, in same manner using (6) SCREWS, H10, as shown.
16. Attach Middle Leg Assembly between assembled sides, P7L and P7R, using (2) BOLTS, H2, and (2) WASHERS, H3,
on each leg, as shown in Figure 6. Attach “L” SUPPORT PANEL, P22, to table using SCREW, H11, in middle pre-drilled
hole. Note: Velcro will be used as wire harness in future step.
17. Attach LEFT and RIGHT BACK LEGS, P3L and P3R, using (2) BOLTS, H2, and (2) WASHERS, H3, on each leg, as
shown in Figure 4. Note: Hand tighten for now, and then do final tightening with ALLEN WRENCH, T1, once P4 Spreader
is attached in next step.
18. Attach SPREADER, P4, between Legs using (4) SCREWS, H1, as shown in figure 6.
Note: Hand place screws in all four pre-drilled holes to align panel before tightening.
Velcro
ASSEMBLY INSTRUCTIONS (CONT.)
9
CAUTION:
P4 SPREADER MUST BE CENTERED
CORRECTLY ONTO PRE-DRILLED HOLES
IN LEGS BEFORE ATTACHING WITH H1
SCREWS.
H1
H1
H1
H10
H11
P22
P4 P3L
P8A
H2 H3
P3R
P8B
P22
H2
H3

ASSEMBLY INSTRUCTIONS (CONT.)
10
Figure 7
H5 Bolt
H7
Washer
P15
Note: Hinge Gear Assemblies Must Mesh
Note: This Hinge is Threaded and Must Be on Inside
CAUTION:
Pinch Point
CAUTION:
Pinch Point
P5
P5
Reset Button
Reset
Button
No Gap
No Gap
Ligature
Bundle of
White Wire
P16
Hinge Set
P16
Hinge Set
P7R
Back Side
Apron
P6R
Front Side
Apron
Note: This Hinge is NOT Threaded
and Must Be on Outside
H7
Washer
19. With the help of another adult, set both completed assemblies upright and position so gears face each other as shown
in Figure 7. Using (2) HINGE SETS, P16, connect assemblies using BOLT, H5, and Washer, H7, as shown in Figure 7.
The bolts should be snug, but NOT over tightened as this is a pivot area. Note: Hinge gear assemblies must mesh together,
per diagram, and there should be no gap between playfields. Also, only one hinge plate per set is threaded and must be
installed on the inside of each playfield side.
20. Place TARGET BOARD, P15, with red hole at the top, into position with the sides resting in the grooves of the braces
on the side panels and against the front of the ramp.
21. Attach the RESET BUTTON, with the long white wire, through the hole in the FRONT END APRON, P5, by removing
the washer and nut on the back of the Reset Button, feeding the Reset Button and wire through the hole from the front and
re-attaching the washer and nut. Note: Be careful not to damage or break wire connections while attaching Reset Button.
Reset Button -
(this ships
pre-wired to
Target Board)