Haulotte Group HA12IP User manual

Operator's manual
HA12IP - HA33JE - HA15IP - HA43JE
4000358100 E 12.14 USA / GB
Operator's manual
HA12IP - HA33JE - HA15IP - HA43JE
4000358100
E 12.14
USA

2 4000358100 E 12.14 USA
HA12IP - HA33JE - HA15IP - HA43JE

3
CONTENTS
Operator's manual
CONTENTS
1 - Operator's manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
2 - After Sales Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
3 - Compliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
4 - HAULOTTE Services® contact details . . . . . . . . . . . . . . . 9
A
SAFETY PRECAUTIONS
1 - Recommendations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
1.1 - Operator's manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
1.2 - Symbols used . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
1.3 - Label colors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
2 - Pre-operation instructions. . . . . . . . . . . . . . . . . . . . . . . . 13
2.1 - General instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
2.2 - Specific instructions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
3 - Operation instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
3.1 - Prohibitions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
3.2 - Potential risks. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
3.2.1 - Risk of command system disturbance . . . . . . . . . . . . . . . . . . . . 15
3.2.2 - Risk of falling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
3.2.3 - Risk of electrocution . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
3.2.4 - Risk of uncontrolled movement and overturning . . . . . . . . . . . . 16
3.2.5 - Risk of burns and explosion . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
3.2.6 - Risk of crushing and collision . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
B
INTERVENOR'S RESPONSIBILITY
1 - Owner's (or hirer's) responsibility. . . . . . . . . . . . . . . . . . 19
2 - Employer's responsibility . . . . . . . . . . . . . . . . . . . . . . . . 19
3 - Trainer's responsibility . . . . . . . . . . . . . . . . . . . . . . . . . . 19
4 - Operator's responsibility . . . . . . . . . . . . . . . . . . . . . . . . . 19
5 - Inspection and maintenance . . . . . . . . . . . . . . . . . . . . . . 20
C
MACHINE LAYOUT
1 - Identification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
2 - Main components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
3 - Safety devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
3.1 - Turntable rotation pin. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26
3.2 - Sliding (or swinging) intermediate guardrail. . . . . . . . . . . . . . . . . . . . . . . . . .28
3.3 - Anchorage point (Please see machine configuration) . . . . . . . . . . . . . . .28
4 - Labels. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
4.1 - Classification plan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
4.1.1 - Red labels. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
4.1.2 - Orange labels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
4.1.3 - Yellow labels. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
4.1.4 - Other labels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
4.1.5 - Green labels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
4.1.6 - Blue labels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
4.2 - Identification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
5 - Control boxes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
5.1 - Ground control box - Emergency control box. . . . . . . . . . . . . . . . . . . . . 54
5.2 - Platform control box . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
5.3 - Various components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60

4
Operator's manual
D
OPERATING PRINCIPLE
1 - Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
2 - Safety devices. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
2.1 - Activation of controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
2.2 - Drive speed. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
2.3 - Electronic variable speed drive. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
2.4 - On-board electronics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
2.5 - Thermostat location / limitation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
2.6 - Load limiting in the platform (if fitted) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
2.7 - Chassis tilt . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
2.8 - Battery discharge indicator-Hour meter . . . . . . . . . . . . . . . . . . . . . . . . . . 63
2.8.1 - Hour meter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
2.8.2 - Automatic reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
2.9 - On-board charger . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
2.9.1 - Black charger . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
2.9.2 - Metal charger . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
2.10 - Drive buzzer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
E
DRIVING
1 - Recommendations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
2 - Checks before use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
2.1 - Visual inspections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
2.1.1 - General mechanical functions . . . . . . . . . . . . . . . . . . . . . . . . . . 67
2.1.2 - Environment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
2.2 - Functional tests . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70
2.2.1 - Safety features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70
2.2.2 - Ground box controls (emergency station) . . . . . . . . . . . . . . . . . 70
2.2.3 - Platform box controls (driving station) . . . . . . . . . . . . . . . . . . . . 71
2.3 - Periodical checks. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72
2.4 - Repairs and adjustments. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72
2.5 - Inspection / Testing requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72
3 - Operation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73
3.1 - Test procedure. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73
3.1.1 - E-stop button operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73
3.1.2 - Tilt sensor switch operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73
3.1.3 - Visual and sound alarms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74
3.1.4 - Weighing system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74
3.1.5 - Movement safety end of drive contactors. . . . . . . . . . . . . . . . . . 74
3.2 - Operation from ground position . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75
3.2.1 - Machine start-up. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75
3.2.2 - Machine shutdown . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75
3.2.3 - Movement control. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75
3.2.4 - Other controls. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76
3.3 - Operations from the platform . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77
3.3.1 - Machine start-up. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77
3.3.2 - Machine shutdown . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77
3.3.3 - Movement control. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78
3.3.4 - Other controls. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79

5
CONTENTS
Operator's manual
F
SPECIAL PROCEDURE
1 - Emergency lowering. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81
1.1 - Principle. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81
1.2 - Procedure. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81
1.3 - Extraordinary procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81
2 - Lowering for repairs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83
2.1 - Principle. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83
2.2 - Procedure. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83
3 - Towing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84
3.1 - Disengaging the drive hubs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84
3.2 - Re-engaging the drive hubs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84
4 - Loading and unloading . . . . . . . . . . . . . . . . . . . . . . . . . . 85
4.1 - Principle. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85
4.1.1 - Lifting operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86
4.2 - Putting in transport position. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87
4.3 - Unloading . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88
4.4 - Warning. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88
4.5 - Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88
G
TECHNICAL SPECIFICATIONS
1 - Main characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89
2 - Overall dimensions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92
3 - Working area / Range of motion . . . . . . . . . . . . . . . . . . . 94
3.1 - Machine HA12IP - HA33JE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94
3.2 - Machine HA15IP - HA43JE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95
4 - AS - CE standard specificities . . . . . . . . . . . . . . . . . . . . 96
4.1 - Overload test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96
4.2 - Functional test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96
4.3 - Stability test. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97
5 - Declaration of conformity . . . . . . . . . . . . . . . . . . . . . . . . 99
H
INTERVENTION REGISTER
1 - Intervention register . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101

6
Operator's manual

7
4000358100 E 12.14 USA
HA12IP - HA33JE - HA15IP - HA43JE
You have just purchased a HAULOTTE® product
and we would like to thank you for your business.
1 - Operator's manual
As stated on the delivery slip, this manual is one of the documents in the on-board document holder
provided upon delivery of your HAULOTTE® machine.
The operator manual is a translation of the original instructions.
Safe operation of this product can only be assured if you follow the operating instructions contained in
this manual are followed.
We would particularly like to draw your attention to 2 essential points :
• Compliance with safety instruction (machine, use, environment)
• Use of the equipment within the performance limits.
2 - After Sales Service
Our HAULOTTE Services® After Sales Service is at your disposal throughout your machine's service
life to ensure the optimum use of your HAULOTTE product.
• When contacting our After Sales Service, ensure that you provide the machine model and serial
number.
• When ordering any consumables or spare parts, please use this manual and the Haulotte Essential
catalogue to receive your genuine HAULOTTE spare parts, your only guarantee of parts
interchangeability and correct machine operation..
• If there is an equipment malfunction involving a HAULOTTE® product, then contact HAULOTTE
Services® immediately even if the malfunction does not involve material and/or bodily damage..
• HAULOTTE® must be informed in the event of an incident that either involves one of these products
or has caused bodily injury or significant deterioration of property (personal property or the product);
contact HAULOTTE Services® immediately (See : HAULOTTE Services® contact details)
With regard to the designation of our equipment, we stress that this is purely for commercial purposes and
not to be confused with the technical specifications. Only the specifications in this manual should be used
to study the suitability of the equipment for the intended use.

8 4000358100 E 12.14 USA
HA12IP - HA33JE - HA15IP - HA43JE
3 - Compliance
We would like to remind you that HAULOTTE® complies with the provisions of any applicable
directives applicable to this type of machine.
HAULOTTE advises you that NO modifications carried out without the written permission
of HAULOTTE® will void the HAULOTTE warranty..
HAULOTTE® cannot be held liable for any changes to the technical specifications contained in this
manual.
HAULOTTE® reserves the right to alter technical specifications and to make improvements or
modifications to the machine without modifying this manual.
Certain options can modify the machine's operating characteristics and its associated safety. If your
machine was originally delivered with options fitted, replacing a safety component associated with a
particular options not require any particular precautions other than those associated with the installation
itself (static test).
Otherwise, it is essential to follow the manufacturer's recommendations as stated below :
• Installation by authorised HAULOTTE® personnel only.
• Update the manufacturer's identification plate.
• Have stability tests carried out by a certified agency/competent person.
• Ensure label compliance.

9
4000358100 E 12.14 USA
HA12IP - HA33JE - HA15IP - HA43JE
4 - HAULOTTE Services® contact details
HAULOTTE Services® contact details
HAULOTTE FRANCE
PARC DES LUMIERES
601 RUE NICEPHORE NIEPCE
69800 SAINT-PRIEST
TECHNICAL Department:
[phone]
SPARE PARTS : [phone]
FAX : [phone]
E-mail : [e-mail]
www.haulotte.fr
HAULOTTE ITALIA
VIA LOMBARDIA 15
20098 SAN GIULIANO MILANESE
(MI)
TEL: [phone]
FAX: [phone]
E-mail : [e-mail]
www.haulotte.it
HAULOTTE HUBARBEITSBÜHNEN GmbH
AN DER MÖHLINHALLE 1
D-79189 BAD KROZINGEN-HAUSEN
TEL : [phone]
FAX : [phone]
E.mail : [email protected].com
www.haulotte.de
HAULOTTE VOSTOK
35, SVOBODY STREET
Bldg. 19
125362 MOSCOW
RUSSIA
TEL/FAX : [phone] / 03
E.mail : [e-mail]
www.haulotte-international.com
HAULOTTE DO BRASIL
AV. Tucunaré, 790
CEP: 06460-020 – TAMBORE
BARUERI – SAO PAULO – BRASIL
TEL : [phone]
FAX : [phone]
E.mail : [email protected]om.br
www.haulotte.com.br
HAULOTTE IBERICA
C/ARGENTINA N° 13 - P.I. LA GARENA
28806 ALCALA DE HENARES
MADRID
TEL : [phone]
TEL SAT : [phone]
FAX : [phone]
E.mail : [email protected]om
www.haulotte.es
HAULOTTE POLSKA Sp. Z.o.o.
UL. GRANICZNA 22
05-090 RASZYN - JANKI-
TEL : [phone]
FAX : [phone]
E-mail :
haulottepolsk[email protected]
www.haulotte.pl
HAULOTTE MÉXICO, Sa de Cv
Calle 9 Este, Lote 18, Civac, Jiutepec,
Morelos
CP 62500 Cuernavaca
México
TEL : [phone]
FAX : [phone]
E-mail : [email protected]
www.haulotte-international.com
HAULOTTE PORTUGAL
ESTRADA NACIONAL NUM. 10
KM. 140 - LETRA K
2695 - 066 BOBADELA LRS
TEL : + 351 21 995 98 10
FAX : + 351 21 995 98 19
E.mail : haulotteportug[email protected]
www.haulotte.es
HAULOTTE SINGAPORE Pte Ltd.
No.26 CHANGI NORTH WAY,
SINGAPORE 498812
Parts and service Hotline:
[phone]
FAX : [phone]
E-mail: [e-mail]
www.haulotte.sg
HAULOTTE MIDDLE EAST FZE
PO BOX 293881
Dubaï Airport Free Zone
DUBAÏ
United Arab Emirates
TEL : [phone]
FAX : [phone]
E-mail : haulottemiddle-
[email protected]
www.haulotte-international.com
HAULOTTE SCANDINAVIA AB
Taljegårdsgatan 12
431 53 Mölndal
SWEDEN
TEL : [phone]
FAX : [phone]
E-mail : [email protected]tte.com
[email protected]om
www.haulotte.se
HAULOTTE TRADING (SHANGHAI)
Co. Ltd.
#7 WORKSHOP
No 191 HUA JIN ROAD
MIN HANG DISTRICT
SHANGHAI 201108 CHINA
TEL : [phone]
FAX : [phone]
E-mail :
[email protected]
www.haulotte.cn
HAULOTTE ARGENTINA
Ruta Panamericana Km. 34,300
(Ramal A Escobar)
1615 Gran Bourg
(Provincia de Buenos Aires)
Argentina
TEL.: [phone]
FAX. [phone]
E-mail : [e-mail]
www.haulotte-international.com
HAULOTTE UK Ltd
STAFFORD PARK 6
TELFORD - SHROPSHIRE TF3 3AT
TEL : [phone]
FAX : + 44 (0)1952 292758
E.mail : [e-mail]
www.haulotte.co.uk
HAULOTTE GROUP / BILJAX
125 TAYLOR PARKWAY
ARCHBOLD, OH 43502 – USA
TEL : [phone]
FAX :[phone]
Toll free : [phone]
E.mail : [email protected].com
www.haulotte-usa.com
HAULOTTE GROUP
1301 E PATRICK STREET
FREDERICK, MD 21701 – USA
TEL : [phone]
FAX :[phone]
Toll free : [phone]
E.mail : [email protected]om
www.haulotte
HAULOTTE CHILE
El Arroyo 840
Lampa (9380000)
Santiago (RM)
TEL : + 562 2 3727630
E.mail : [email protected]
www.haulotte-chile.com
-usa.com
HAULOTTE NETHERLANDS BV
Koopvaardijweg 26
4906 CV OOSTERHOUT - Nederland
TEL : [phone]
FAX : [phone]
E.mail :
[email protected]
HAULOTTE AUSTRALIA PTY Ltd
46 GREENS ROAD
DANDENONG – VIC – 3175
TEL : [phone]
FAX : [phone]
E.mail :
l
[e-mail]
hl
HAULOTTE INDIA
Unit No. 1205, 12th foor,Bhumiraj Costarica,
Plot No. 1&2, Sector 18,
Palm Beach Road,
Sanpada, Navi Mumbai- 400 705
Maharashtra, INDIA
Tel. : [phone] to 35
E-mail : [email protected]
www.haulotte.in

10 4000358100 E 12.14 USA
HA12IP - HA33JE - HA15IP - HA43JE

A
B
C
D
E
F
G
H
I
11
4000358100 E 12.14 USA
HA12IP - HA33JE - HA15IP - HA43JE
A - Safety precautions
Safety precautions
1 - Recommendations
1.1 - OPERATOR'S MANUAL
This operators manual is specific to the HAULOTTE® products listed on the cover page of this
manual..
1.2 - SYMBOLS USED
Symbols are used to alert the operator to safety precautions or to highlight practical
information.
Legend
The operator manual does not replace the basic training required for all worksite equipment operators.
HAULOTTE® has compiled this manual to assist in safe and efficient operation of the products covered
by the manual.
This manual must be kept on the machine (or in the cab in its storage case. The manual must be available
to all operators and must be kept in good condition. Additional copies can be ordered from HAULOTTE
Services®.
Symbol Description
Danger : Risk of injury or death
Caution : Risk of material damage
Prohibition relating to work safety and quality
Reminder : No identified risk, but a reminder of the need for common sense,
good practice or pre-action prerequisites
Cross-reference to another part of the manual (see section or sheet)
Cross-reference to another manual (see manual)
Cross-reference to repairs (contact HAULOTTE Services®)
N.B. : Additional technical information

12 4000358100 E 12.14 USA
HA12IP - HA33JE - HA15IP - HA43JE
A - Safety precautions
1.3 - LABEL COLORS
The potential dangers and any specific regulations are indicated around the product by labels
and identification plates.
Familiarize yourself with the labels and their respective color codes.
Label color code
Label color code-For Russia and the Ukraine only
The labels must be kept in good condition. Additional decals can be ordered from HAULOTTE Services®.
Labels Color Description
Red Potentially fatal danger
Orange Risk of serious injury
Yellow Risk of material damage and/or minor injury
Other Additional technical information
Green Maintenance operation or information
Labels Color Description
Red Prohibitions - Danger
Yellow Warning : Risk of material damage and/or minor injury
Blue Precaution
Blue Information
Other Additional technical information

A
B
C
D
E
F
G
H
I
13
4000358100 E 12.14 USA
HA12IP - HA33JE - HA15IP - HA43JE
A - Safety precautions
2 - Pre-operation instructions
2.1 - GENERAL INSTRUCTIONS
• On soft, unstable or cluttered ground.
• With wind blowing faster than the permissible limit. Check the maximum allowable value in the
technical characteristics / specifications ( Section G 1-Main characteristics). Consult the
Beaufort scale ( Section A 3.2.4-Risk of uncontrolled movement and overturning).
• Close to power lines. Respect the safety distance ( Section A 3.2.3-Risk of electrocution).
• At ambient temperatures higher than 45 °C(113 °F) and lower than -15 °C(5 °F) .
Consult HAULOTTE® if it is necessary to work outside this range.
• In an explosive atmosphere.
• During storms (risk of lightning).
• In the presence of strong electromagnetic fields.
N.B.-:-You are advised to use the machine under "NORMAL" climatic conditions.. If you need to use
the machine in climatic conditions likely to cause deterioration (extreme : humidity, temperatures,
salinity, corrosiveness, atmospheric pressure), contact HAULOTTE Services®. Reduce intervals
between servicing.
N.B.-:-Whilst the machine is not in use, care must be taken to ensure that if the machine is not locked
in a secure location, that the unit key switch is removed to prevent unauthorised use of the machine.
2.2 - SPECIFIC INSTRUCTIONS
• If the load in the platform exceeds the maximum load authorized. Check the maximum allowable value
in the technical characteristics / specifications ( Section G 1-Main characteristics).
• If the ground slope is greater than the permissible limit. Check the maximum allowable value in the
technical characteristics / specifications ( Section G 1-Main characteristics).
• At night unless the machine is equipped with the optional light.
• If the number of persons exceeds the permissible limit. Check the maximum allowable value in the
technical characteristics / specifications ( Section G 1-Main characteristics)
• If the side force is greater than the permissible force. Check the maximum
allowable value in the technical characteristics / specifications ( Section G 1-
Main characteristics)
• The employer has the obligation to issue a driving permit to the operator.
• The employer is obliged to inform the operator of the local regulations.
Do not operate the product in the following situations :
Do not operate the product in the following situations :

14 4000358100 E 12.14 USA
HA12IP - HA33JE - HA15IP - HA43JE
A - Safety precautions
3 - Operation instructions
3.1 - PROHIBITIONS
It is preferable to operate the machine on flat, consolidated ground (tarmac, concrete, etc.).
• Never use a faulty machine (hydraulic leaks, worn tires/tyres, malfunction).
• Never operate the machine controls suddenly.
• Never place the machine against a structure to hold that structure in place.
• Never use the machine to tow other machines or to drag materials.
• Never expose the batteries or electrical components to water (pressure cleaner, rain).
• Never disable the safety devices.
• Do not make contact with a fixed or mobile obstacle. The contact can cause premature deterioration of
the structure and lead to the corruption of certain safety elements.
• Do not climb onto the covers.
• Never use the machine with only an operator in the platform. A second person competent in the operation
of emergency retrieval, should be present on the ground in case of an emergency.
• Never use the machine when the platform is cluttered.
• Never increase the surface area of the platform by using floor extensions or accessories not authorized
by HAULOTTE®.
• Never leave the hydraulic cylinders fully extended or retracted before switching off the machine, or when
stationary for an extended period of time.
• Never use the machine with material or objects hanging from the guardrail or the boom.
• Never use the machine with elements that can increase the wind force (panels).
• Never increase the working height by using attachments (ladder).
• Never use the guardrail as a means of access for climbing in or out of the platform. The basket can be
easily accessed in its low position. For machines fitted with : Steps have been provided for this purpose
where required.
• Never climb on the guardrail.
• Never use the machine without fully lowering the sliding midrail or without closing the platform entry
gate.
• Never use the machine as a crane, material lift or elevator.
• Never use the machine for any other purpose than to transport people, their tools and material to the
desired place.
• Never drive fast in narrow or cluttered areas. Keep speed under control in bends.
• Never tow the machine over extended distances (it must be transported on a trailer). In case of a machine
failure, it is possible to tow it to load it onto a trailer ( Section F 3Towing).

A
B
C
D
E
F
G
H
I
15
4000358100 E 12.14 USA
HA12IP - HA33JE - HA15IP - HA43JE
A - Safety precautions
3.2 - POTENTIAL RISKS
3.2.1 - Risk of command system disturbance
Risk of disrupted movement. Maintain clearance from high voltage lines or magnetic fields.
3.2.2 - Risk of falling
When in the platform, respect the following instructions :
• Carry individual protection equipment adapted to the work conditions and local
rules.
• Avoid contact with fixed or mobile obstacles (other machines).
• Ensure that the adjustable midrail is closed (low position and against the guardrails).
• Ensure that the gate is closed and locked (For machines fitted with).
• Hold on securely to the guardrails during elevation and driving.
• Do not sit, stand, or climb on the platform guard rails.
• Ensure that guard rails are correctly installed and locked.
• Always keep your feet firmly on the floor of the platform.
• Remove any trace of oil or grease from the steps, floor, handrail and the guardrails.
• Keep the floor of the platform free of debris.
• Do not leave the platform until it is fully in its stowed position.
• Do not climb on to the platform if the machine is not in the stowed position.
To climb up or climb down from the platform :
• The machine must be completely stowed.
• Face the machine to access the entry opening to the platform
• Keep 3 support points between the steps and the guardrail

16 4000358100 E 12.14 USA
HA12IP - HA33JE - HA15IP - HA43JE
A - Safety precautions
3.2.3 - Risk of electrocution
The machine is not electrically insulated and does not offer any insulation
protection.
The risks of electrocution are high in the following situations :
• Close to live power lines, consider the movement of the machine and the sway of the electric power
lines particularly in windy conditions.
• In the event that you were to make accidental contact with a high voltage line, wait for the power to
the line to be switched off before operating the machine.
• During storms.
Never use the machine as a welding earth.
Maintain a minimum safe distance with regard to power lines and electrical devices.
Respect the local rules and the minimum safety distance from power lines.
Minimum safe approach distances
N.B.-:-This table is applicable, except when the local regulations are more strict.
3.2.4 - Risk of uncontrolled movement and overturning
When in the platform, respect the following instructions :
• Before operating the machine on any indoor or outdoor surface (premises, bridge,
truck, etc.), check that the surface is capable of supporting the combined machine
weight and platform capacity. Check the maximum allowable value in the technical characteristics /
specifications ( Section G 1-Main characteristics).
• Remain vigilant of driving direction reversal at the platform. Check the driving direction with the help
of the red or green arrow on the chassis relative to the red and green arrows on the platform control
box.
• Always ensure that the chassis is never driven any closer than 1 m(3 ft3 in) to holes, bumps, slopes,
obstructions, debris and ground coverings that may hide holes and other dangers.
• During motion direction reversal from the platform or ground control box, the joysticks or switches
must be in neutral position before reversing the direction of motion.
• Taking note of the overall load dimensions and weight, place the loads in the centre of the platform or
distribute them it a uniform manner.
• If the tilt alarm sounds when the platform is raised, lower platform completely, then reposition machine
onto level ground before raising platform.
Electric voltage Minimum safety distance
Mètre Feet
0 - 300 V Avoid contact
300 V - 50 kV 310
50 - 200 kV 515
200 - 350 kV 620
350 - 500 kV 825
500 - 750 kV 11 35
750 - 1000 kV 14 45

A
B
C
D
E
F
G
H
I
17
4000358100 E 12.14 USA
HA12IP - HA33JE - HA15IP - HA43JE
A - Safety precautions
N.B.-:-The Beaufort scale measures the wind force with a graduation system. A wind speed range at 10
m(32 ft9 in) above flat, clear land is associated with each degree.
Beaufort scale
• Do not drive the machine on slopes or tilts beyond the design limits. Check the maximum allowable value
in the technical characteristics / specifications( Section G 1-Main characteristics).
• Do not travel down slopes in high speed.
• Do not use the machine (elevation and travel) on an incline greater than that permitted by the slope
sensor.
• Do not drive in reverse (direction opposite the field of vision).
• Never use the machine in winds exceeding the permissible limit.
• Do not increase the surface area exposed to wind. The greater the surface area exposed, the more
unstable the machine becomes.
• While driving, always place the arrow above the rear axle, in the direction of movement.
• While driving on a slope, always orient the machine in the direction of the slope.
• Do not pull or push objects with the boom.
Force Meteorological
description Observed effects m/s km/h mph
0Calm Smoke rises vertically. 0 - 0,2 0 - 1 0 - 0,62
1Very light breeze Smoke indicates the wind direction. 0,3 - 1,5 1 - 5 0,62 - 3,11
2Light breeze Wind felt on the face. Leaves
rustle. Weather vanes turn. 1,6 - 3,3 6 - 11 3,72 - 6,84
3Slight breeze Leaves and small twigs in constant
motion. Flags move slightly. 3,4 - 5,4 12 - 19 7,46 - 11,8
4Nice breeze Raised dust and loose papers.
Small branches are moved. 5,5 - 7,9 20 - 28 12,43 - 17,4
5Nice breeze Small trees in leaf to sway. Crested
wavelets form on inland waterways. 8,0 - 10,7 29 - 38 18,02 - 23,6
6Cool wind
Large branches in motion. Power
lines and chimneys 'sing'.
Umbrellas used with difficulty.
10,8 - 13,8 39 - 49 24,23 - 30,45
7Strong cool wind
Whole trees in motion.
Inconvenience felt when walking
against wind.
13,9 - 17,1 50 - 61 31 - 37,9
8Squall Some branches break. Generally
we cannot walk against the wind. 17,2 - 20,7 62 - 74 38,53 - 45,98
9Strong squall
The wind causes slight damage to
buildings. Tiles and chimney stacks
are blown off.
20,8 - 24,4 75 - 88 46,60 - 54,68

18 4000358100 E 12.14 USA
HA12IP - HA33JE - HA15IP - HA43JE
A - Safety precautions
3.2.5 - Risk of burns and explosion
N.B.-:-Acid is neutralized with sodium bicarbonate and water.
3.2.6 - Risk of crushing and collision
When in the platform, respect the following instructions :
• During operation, keep all the parts of the body inside the platform.
• To position the machine close to obstacles, use the raise controls (arm, boom, etc.) instead of the
drive controls.
• Ensure there are no obstacles (structure) in the work area.
• When driving, position the platform so as to provide the best visibility possible.
• Always obtain assistance from a guide on the ground when manoeuvring.
• All the personnel in the platform or on the within the vicinity of the machine must wear Personal
Protection Equipment (safety helmet, etc.).
• When lifting or lowering the basket and during driving, the operator must check that the area above,
below and to each side of the machine are clear.
• When moving the machine, ensure that the machine operating areas is free of persons and obstacles.
For any intervention on the power sources, wear glasses and protective clothes (acid spray).
• Do not work in an explosive or flammable atmosphere (spark, flame, etc.).
• Do not touch the hot parts of the hydraulic power source (engine, filters, etc.).
• Do not bridge the battery terminals with metallic objects.
• Do not service the battery in proximity of spark, open flame, glowing/burning cigarette.
Do not operate other machines (crane, aerial work platform, etc.) in the work area.
Take account of the distance, reduced visibility and blind spots during use of the machine.

A
B
C
D
E
F
G
H
I
19
4000358100 E 12.14 USA
HA12IP - HA33JE - HA15IP - HA43JE
B - Intervenor's responsibility
Intervenor's responsibility
1 - Owner's (or hirer's) responsibility
The owner (or hirer) has the obligation to inform operators of the instructions contained in the Operator
Manual.
The owner (or hirer) has the obligation to renew all manuals or labels that are either missing or in bad
condition. Additional copies can be ordered from HAULOTTE Services®.
The owner (or hirer) is responsible for applying the local regulations regarding operation of the
machine.
2 - Employer's responsibility
The employer has the obligation to issue a driving permit to the operator.
N.B.-:-In accordance with the regulation of the country where the machine is operating, the user must
be authorized by the doctor of Labour Ministry to operate the machine.
3 - Trainer's responsibility
The trainer must be qualified to provide training to operators in accordance with applicable local
regulations. The training must be given in an obstacle-free area until the trainee is considered
competent as defined by the training program undertaken.
4 - Operator's responsibility
The operator must read and understand the contents of this manual and the labels affixed on the
machine.
The operator must inform the owner (or hirer) if the manual or any labels are missing or in poor
condition, and of any malfunction of the machine.
The operator may only operate the machine for the purpose intended by the manufacturer.
All operators must become familiar with and fully understand the emergency controls and how to
operate the machine in an emergency as a component of their formal operator training.
The operator has the obligation stop using the machine in the event of malfunction or safety problems
on the machine or in the work area and report the problem to his/her supervisor.
Forbid anyone from operating the machine who is :
• Under the influence of drugs, alcohol, etc..
• Subject to fits, loss of motor skills, dizziness, etc..
Only authorized and qualified operators may operate HAULOTTE® machines.

20 4000358100 E 12.14 USA
HA12IP - HA33JE - HA15IP - HA43JE
B - Intervenor's responsibility
5 - Inspection and maintenance
The inspection and maintenance table below, identifies the role and the responsibilities of each party
in periodical machine maintenance..
Inspections and maintenance
If the machine is operated in a hostile environment or intensively, increase the frequency of maintenance.
Type of
intervention Frequency Person-in-charge Intervenor Reference document
Pre-delivery
inspection
Before each delivery
of sold, hired or
resold equipment
Owner (or hirer) Qualified HAULOTTE
Services® technician Operator's manual
Pre-operation
inspection
Before operation or
when the operator
changes
Operator Operator Operator's manual
Periodical
preventive
maintenance
At the specified
intervals (250 hours
or 1 year)
Owner (or hirer)
On-site technician or
qualified HAULOTTE
Services® technician
Maintenance book
Periodical visit
2 times a year or at
the latest 6 months
after the last periodic
visit, and according
to the local
regulations
Owner (or hirer)
Organization or technician
approved by the employer
or by the intermediary of
HAULOTTE Services® in
accordance with
the HAULOTTE
Services® contract
Maintenance book