Haven Q Series User manual

havenhomelighting.com RevN
1
Q SERIES – FULL COLOR DUO LED CONTROLLER
OPERATIONS MANUAL
Storage and MountingWhat’s in the Box?
Q Series – Full Color Duo LED Controller
This lighting controller must be mounted in a clean and dry environment with good ventilation. Do not block or cover the vents in the
enclosure. Avoid mounting the controller within a metal enclosure. If this is a requirement, we highly recommend that your purchase
an antenna extender cable and mount the antenna outside the metal enclosure.
Q Series – Full Color Wireless Wall Switch
The light switch should be mounted indoors in a clean and dry environment. Do not install switch on a metal junction box. It will
greatly reduce signal range.
1 x Q Series – Full Color Duo LED Controller
2 x Wood Mounting Screws
6 x Dry Wall Anchors & Screws
2 x Wireless Wall Switch w/ Screws
2 x Wireless Wall Switch Cover w/ Screws
2 x Double Sided Tape (for non-screw mounting option)
1 x Power Supply
Installation on dry wall Installation with wall receptical Installation with double sided tape
(Dry wall mounting optional with
included anchors and screws or
double-sided tape)
Note: DO NOT CONNECT
TO POWER UNTIL STEP 5
STEP 1: Connect Antenna STEP 2: Connect wires to
connectors
STEP 3: Plug in connectors STEP 4: Mount controller STEP 5: Connect to power
COM RED GRN BLU

havenhomelighting.com RevN
2
LIGHT
AREA A
LIGHT
AREA
A&B
TO LIGHT AREA B
TO LIGHT AREA A
LIGHT
AREA B
LIGHT
AREA A
LIGHT
AREA B
1 Q Series Full Color LED Light
2 Q Series Full Color LED Spot Strip
3 Q Series Full Color LED Strip
1
2
3
*Additional
Wall Switches
sold seperately.
Add up to 10.
1 Q Series Full Color LED Light
2 Q Series Full Color LED Spot Strip
3 Q Series Full Color LED Strip
1
2
3
Note: Factory default switches
are paired to both A & B.
Wiring
COM RED GRN BLU
Lighting Connectors
14 AWG
4 Conductor
Light A Control
(5 Amps)
Feedback
Pairing Button
Fuse 2
Fuse 1
24 VDC Power
Light B Control
(5 Amps)
Antenna
Note: Fuse lights should
be on for proper operation.
Full Color LED Controller

havenhomelighting.com RevN
3
Pattern Rate settings:
In addition to solid colors, the Q Series controller can also show some animated patterns. You can adjust the rate/period of
the pattern by holding the OFF button. While holding you can press NEXT (4) and PREVIOUS (3) buttons to
cycle through the rate/period options.
Pattern Rate Feedback:
Feedback color will change based on transition rate. See chart below.
Operations Guide
White Adjustment:
Press and hold the ON (White) button, while holding you can press COLOR/PATTERN PREVIOUS (3) or NEXT (4)
to cycle through the white color adjustments. Release the ON button to save the new white adjustment value.
Brightness settings:
Each color/pattern has a default brightness level. You can change the brightness using the BRIGHTNESS UP (6) and
DOWN (6) buttons. Feedback color will change based on pattern rate. See chart below.
Colors:
Solids: Patterns:
Red
Fire
Pumpkin
Amber
Tangerine
Merigold
Sunset
Yellow
Lime
Light Green
Green
Sea Foam
Turquoise
Ocean
Deep Blue
Violet
Purple
Lavender
Pink
Hot Pink
[Blend] Red > Pink > Purple
[Blend] Deep Blue > Turquoise > Green
[Blend] All Colors
[Fade] Christmas
[Fade] Fourth of July
[Blink] Halloween
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
16.
17.
18.
19.
20.
21.
22.
23.
24.
25.
26.
Wireless Wall Switch
Feedback LED
ON (White)
ON (Full Color)
(Hold for Patterns)
OFF
Brightness:
Down (6) / Up (5)
Color/Pattern:
Previous (3) / Next (4)

havenhomelighting.com RevN
4
Pairing and Setup
Pattern Rate/Period
Transition Time Feedback Color Automation Link™Button
75 msec Red x5
10 sec Blue x4
30 sec Yellow x3
7 min Purple x2
16 min Turquoise x1
PAIRING MODE COMMANDS
ON + OFF (hold 5 seconds) Pair switch to both lights (A + B)
ON + BRIGHTNESS DOWN (6) (hold 5 seconds) Pair switch to Light A
ON + BRIGHTNESS UP (5) (hold 5 seconds) Pair switch to Light B
OFF + BRIGHTNESS DOWN (6) (hold 5 seconds) Sync Pair (see page X)
OFF + BRIGHTNESS UP (5) (hold 5 seconds) Unpair switch from controller
BRIGHTNESS UP (5) or BRIGHTNESS DOWN (6) Controller will indicate wireless signal strength
Tap the pairing button on the controller to pair a switch or change other settings. The controller will turn o both lights and the green
status LED will turn o. Now that you are in pairing mode you can execute the following commands:
Sync Pair:
This feature is used with multiple controller setups and patter mode. A switch that is sync paired to a controller(s) will reset the
pattern clock to that controller(s) when the HAVEN button is pressed. This will syncronize all of the patterns.
To pair to both LIGHT A and LIGHT B:
STEP 1: Press the PAIRING BUTTON on the
controller to enter PAIRING MODE
STEP 2: Press and hold ON and OFF simultaneously for
6 seconds. Flashing will indicate pairing was successful.
COM RED GRN BLU+ 1 2 COM RED GRN BLU COM RED GRN BLU COM RED GRN BLU
Q SERIES DUO
Pairing Button
Feedback LED
ON (Elegant White)
ON (Full Color)
(Hold for Patterns)
OFF
Brightness:
Down (6) / Up (5)
Color/Pattern:
Previous (3) / Next (4)

havenhomelighting.com RevN
5
10 Amp Controller
Voltage: 10 – 26 V DC
Current: Total Current: 10 Amps
Light Area A: 5 Amps
Light Area B: 5 Amps
Congured to work with Common Cathode LED congurations
(connections to light should be Negative, R, G, B)
120 V AC to 24 V DC Power Supply Included
5 Amp Controller
Voltage: 10 – 26 V DC
Current: Total Current: 5 A
Light Area A: 5 A
Light Area B: 5 A
Congured to work with Common Cathode LED congurations (connections to light should be Negative, R, G, B)
120 V AC to 24 V DC Power Supply Included
Technical Information
6 1
2
"
7 1
2
"
8"
3 7
8
"
4 3
8
"
1"
Dimming Capability: 15 Brightness Levels
White Color Options: 10 White Temperatures
Battery Style: Standard 2032 Battery
Typical Battery Life: 5 Years
Range: Up to 500 ft.
We highly recommend you use our Full Color Wire for any installation where the strips are not directly connected to the controller.
The wire we use is 14 AWG stranded wire that is in wall rated and direct burial rated.
Our LED lights are bright and run at a higher voltage to reduce the amount of current to power them. However, voltage drop
management due to this power transmission is still very important when wiring your system.
Color Information
Wall Switch Technical Data
Wiring Configurations