Havis-Shields P-MFK-5 Configuration guide

INSTALL INSTRUCTIONS P-MID-1 w/P-MFK-5
MIDDLE PARTITION w/MOUNTING FILLER PANEL KIT
1997-2008 CHEVROLET/GMC FULL SIZE PASSENGER VANS
TOOLS REQUIRED:
Power drill
Drill bit set
Ratcheting wrench
Standard & Metric socket set
HARDWARE:
QTY DESCRIPTION PART #
5 ¼” x 1 ½” Hex head Lag Bolt GSM33062
6 ¼” x 1” Hex head Lag Bolt GSM33060
20 ¼-20 x ¾” Carriage Bolt GSM32000
12 ¼-20 Serrated Nut GSM30023
8 ¼-20 Nylock Nut GSM30016
1 5/16-18 Nylock Nut GSM30017
1 5/16-18 x 2” Hex Head Bolt GSM33015
2 5/16 Flat Washer GSM31006
8 ¼” x 1” Fender Washer GSM31014
Main Partition
Frame
Driver Side Upper
Lexan Filler Panel
Upper Center Steel
Filler Panel
Driver Side Lower
Steel Filler Panel
Passenger Side Steel
Door Filler Panel
Passenger Side
Mounting Bracket
(2-Piece) Driver Side
“B” Pillar Mounting
Bracket

P-MID-1^MFK-5_INST_9-07
SUB ASSEMBLY:
1. Remove “C” pillar trim panel. This is necessary for driver side mounting bracket.
2. Position upper center filler to partition and mark mounting holes.
3. Drill 5/16” holes on marks.
Always!
 Read all instructions before installing any Havis-Shields Equipment Corp products.
 Check for obstructions (Wire, brake lines, fuel tank, etc.) before drilling any holes!
 Use hardware provided with install kit
INSTALLATION:
1. ATTACH PARTITION TO FLOOR:
• Place partition carefully into vehicle behind the first
row bench.
• Move bottom of partition forward to the back of seat
base on first row bench.
Note: Driver side mounting leg on partition will be forward of seat belt
hold down on floor of van.
• Pre-drill the (3) driver side mounting leg holes with
3/16” drill bit. Be sure to check for obstructions.
• Attach partition to van floor at driver side mounting leg
using (3) ¼” x 1 ½” Hex head lag bolts.
• Proceed to partitions passenger side mounting leg. Be
sure to check that partition is square with the bench seat.
• Pre-drill the (2) passenger side mounting leg holes with
3/16” drill bit. Be sure to check for obstructions.
• Attach partition to van floor at passenger side mounting
leg using (2) ¼” x 1 ½” Hex head lag bolts. Partition is
now self-supporting.
2. ATTACH (2- PIECE) DRIVER SIDE
“B” PILLAR MOUNTING BRACKET:
• Hold 2-piece driver side mounting
bracket to partition and “C-pillar”
of van.
• Determine proper location to
mount 2-piece bracket to partition.
• Drill (2) 5/16” holes where
mounting bracket and partition
meet.
• Attach bracket to partition using
¼-20 x ¾” Carriage bolts and
¼” x 1 ½” Hex Head Lag Bolts

P-MID-1^MFK-5_INST_9-07
serrated nuts.
• Press partition as far forward and mark mounting holes where driver side mounting
bracket and “C-pillar” come in contact.
• Pre-drill 3/16” holes into “C-pillar”.
• Attach bracket to C-pillar using (3) ¼” x 1” Hex head lag bolts.
• Plastic trim panel must be notched around bracket to mount.
3. ATTACH PASSENGER SIDE MOUNTING BRACEKT:
• Press partition as far forward as
possible and holding bracket to
partition (square tubing section)
determine where to slot headliner to
accept mounting bracket.
• Slot headliner and position mounting
bracket to be flush with vehicle inner
roof support.
• Mark (3) mounting holes and pre-
drill using 3/16” drill bit.
• Attach bracket to vehicle using (3)
¼” x 1” Hex head lag bolts.
• Press partition up to bracket and
mark holes where bracket and
partition come together.
• Drill 5/16” holes on these marks and
bolt partition to bracket using 5/16-
18 x 2” Hex head bolt, washer, and
nylock nut.
4. ATTACH UPPER STEEL CENTER FILLER PANEL:
• Attach upper center filler to partition through the holes pre-drilled at subassembly
using ¼-20 x ¾” Carriage bolts and serrated nuts.
• Tighten all hardware.
Passenger side upper
mounting bracket
5/16-18 x 2”
Hex head bolt
Slot in headliner
Upper Center Filler Panel

P-MID-1^MFK-5_INST_9-07
5. ATTACH DRIVER SIDE UPPER LEXAN FILLER PANEL:
• Position driver side ¼” lexan filler panel to partition so that minimal space is between
the vehicles window, (or window guard) and the lexan filler.
NOTE: It is necessary to keep a 1/8” gap between the window or guard and the filler to allow for
expansion and contraction of the lexan during temperature fluctuations.
• Drill (6) 5/16” holes evenly spaced through both the ¼” lexan filler panel and the
partition frame. Attaching to the frame directly will help to avoid filler rattling.
• Bolt lexan filler to partition using ¼-20 x ¾” carriage bolts and nylock nuts.
6. ATTACH DRIVER SIDE LOWER STEEL FILLER PANEL:
• Position driver side lower aluminum filler panel tight to vehicles interior trim and
floor.
• Using slots in filler panel as a drill guide mark and drill partition using 5/16” drill bit.
• Attach filler panel to partition using ¼-20 x ¾” carriage bolts and serrated nuts.
7. ATTACH PASSENGER SIDE DOOR STEEL FILLER PANEL:
• Position on front row bench in van close side doors.
• Hold filler panel to partition so that it does not interfere door mechanisms.
• Mark and drill 3/16” holes through partition tubing.
• Attach filler to partition using ¼-20 x ¾” Hex head thread cutting bolts.
• Vacuum out all metal shaving and double check door operation.
Driver side upper lexan filler
Lexan
Notched
f
¼-20 x ¾”
Carriage
Passenger Side Upper Steel Filler Panel