Hay AAT15 User manual

INSTRUCTION MANUAL
ABOUT A TABLE
AAT15/AAT20
4 LEGS
By Hee Welling & HAY

The About A Table shares the general
versatility and design language as the rest
of the About A Chair family.
The table features the same powder coated
frame as many of the chairs in the series, and
the organic curves and raised feet convey
a similar light expression.
INTRODUCTION

CARE AND MAINTENANCE CARE AND MAINTENANCE
CAUTION
With a little care you can prolong the life of your
furniture. Follow the instructions for the materials of
your specific product to make sure that it stays in
the best shape for as long as possible.
The information below is only intended as a
general guideline. For more information on how
to remove specific stains, please enquire where
you bought the furniture.
• Always remove stains quickly before they can do
any permanent damage to the furniture.
• Avoid placing the table in direct sunlight or near a
heat source to reduce changes. As linoleum is a
natural material, it will change in colour and will
patinate over time.
• When you move your furniture, make sure you lift it
rather than pulling or pushing it to avoid damaging
the floor, legs and mountings.
• Tighten up the screws after one to two months’ use
and whenever required.
• Avoid improper use such as putting your feet on
the table and standing on it.
• Use coasters under damp, hot or coloured objects
to avoid permanent stains.
• Avoid partially covering the surface, for example
with tablecloths or place mats, as colour variances
may appear.
• Be careful not to scratch or damage the surface
with sharp objects.
LINOLEUM
• Wipe with a clean cloth wrung in water or in a
solution of water and a neutral detergent or soap
flakes. Remove soap residue immediately using a
clean, dry cloth.
• If the surface is scratched or appears matt, use
a care product especially suited to linoleum.
• Stains may be carefully removed using white spirit
(mineral spirit) or a damp nano sponge dipped in
lukewarm water or linoleum care product. Follow up
immediately with a clean, dry cloth. Never use the
nano sponge dry.
• Avoid alkaline detergents such as soft (yellow)
soap, washing soda, lye and scouring powder.
LAMINATE
• Wipe with a clean cloth wrung in water or in a
solution of water and a neutral detergent. Remove
soap residue immediately using a clean, dry cloth.
• Stains may be carefully removed using household
ammonia or with a clean, damp cloth or a nano
sponge wrung in warm water. Never use the nano
sponge dry. Follow up immediately with a clean,
dry cloth.
• Avoid using scouring cream or scouring pads,
as they may scratch the surface.
POWDER COATED OR POLISHED ALUMINIUM
• Wipe with a clean cloth wrung in water or in a
solution of water and a neutral detergent. Remove
soap residue immediately using a clean, dry cloth.
• Avoid using scouring cream or scouring pads,
as they may scratch the surface.

A x 1
J x 8 K x 2 L x 1 M x 1
F x 12 G x 4 H x 4 I x 8
B x 1 C x 4 D x 4 E x 2
PARTS
CAUTION
While assembling, keep the tabletop inside the cardboard box with foam edge in order
to protect the tabletop from scratches etc. Make sure that all parts are included.

2.
Slide the I part into the D part and press it down gently.
Repeat this step on all 4 x D parts.
3.
Place the D part into the B part.
Repeat this step on all 4 x D parts.
5.
Screw 4 x J parts in the shown holes of the E part, using the Allen key (L):
4.
Place the E part in the shown holes of the D parts.
I
BJ
L
D
E

6.
Screw 1 x K part in the shown hole of the E part, using the Allen key (L).
7.
Place the I part into the C part and press it down gently.
Repeat this step on the 4 x C parts.
I
E
C
9.
Place the E part in the shown holes of the C parts.
8.
Place the C part in the shown holes of the B part. Repeat this step on all 4 x C parts.
L
K

10.
Screw 4 x J parts into the shown holes of the E part using the Allen key (L).
12.
Place the H part over the hole of the C part. Screw the G part in the shown holes of the H part
using the Allen key (M). Repeat this step on all 4 x C parts.
11.
Screw 1 x K part in the shown hole of the E part using the Allen key (L).
13.
Screw the D part to the tabletop using the F parts.
J
K
L
F
L
H
M
G
Make sure the table
is upright when
mounting the base.

14.

Havnen 1 8700 Horsens Denmark
[phone] / [e-mail]
12092017
5 710441 246565
ITEM NO. 706356