Healthcraft Invisia User manual

All mount points fasten
into structural wood
(wood studs,
reinforced wood
framing, etc.)
Minimum one (center)
mount point fastens into
structural wood; no
structure available for
other mount points
None of the mount
points align with the
available structure
#10 x 2" S/S Screw
and Lock Washer (into
wood)
#10 x 2" S/S Screw and
Lock Washer (into wood)
+ SnapToggles® with
#10 x 2" S/S Bolts
(for areas w/o structure)
WE DO NOT
RECOMMEND THIS
PRODUCT BE
INSTALLED USING
ONLY SNAP
TOGGLES®.
500lbs load capacity 350lbs load capacity N/A
PARTIAL MOUNTING
STRUCTURE
AVAILABLE
NO MOUNTING
STRUCTURE
AVAILABLE
FULL MOUNTING
STRUCTURE
(RECOMMENDED)
DC155 REV B Page 1 of 4
Specifications subject to change without notice.
Installation Instructions:
WTRH-BN / WTRH-CRP / WTRH-PCW
THANK YOU...
Thank you for purchasing the Invisia™ Wall Toilet Roll Holder.
We are confident that you will find the unique design and
durable construction of this product to be of great assistance
in your daily routine.
To fully enjoy your Invisia™ Wall Toilet Roll Holder, please
take a few moments to read these instructions. You should
store these instructions in a safe place for future reference.
SAFETY CONSIDERATIONS
CAUTION: It is your responsibility to see that your Invisia™
Wall Toilet Roll Holder is properly assembled, installed, and
cared for. Failure to follow instructions in this manual could
result in serious injury. Support rails can be slippery when wet
- use this product with caution.
INVISIA™ WALL TOILET ROLL HOLDER INSTALLATION
The Invisia™ Wall Toilet Roll Holder should only be installed in
areas where the mounting surface is structurally sound.
Strengthening modifications may be required (see page 3 for
details). Should not be installed in fiberglass / acrylic shower
enclosures with insufficient stiffness and strength. Should not be
installed into metal studs. If you are not equipped to undertake
the outlined work we recommend that you have your Invisia™
Wall Toilet Roll Holder installed by a qualified contractor.
Suggested maximum user weight of support rail is
500lbs/227kg, however this rating is conditional upon
suitable fasteners and supporting surface.
WARRANTY
All HealthCraft™ Products are covered by a one year limited
warranty with the exception of hand grips which are subject to
normal wear. Buyer hereby indemnifies, agrees to hold
harmless and defend HealthCraft™ Products Inc. from and
against any and all liabilities, claims, (founded and
unfounded), losses, damages, costs and expenses (including
without limitation consequential damages and reasonable
professional fees) resulting from buyers specification,
application, or improper use of goods described hereon;
buyers omission or neglect.
HealthCraft™ Products Inc. does not assume any liability for
damage resulting from services performed by others or faulty
installation, misuse or misapplication of goods sold by
HealthCraft™ Products Inc.
HealthCraft™ Products Inc. shall not be liable for prospective
profits or special, indirect, or consequential damages, or for
the cost of any corrective work done without HealthCraft™
Products Inc. prior approval. HealthCraft™ Products Inc. total
liability hereunder shall in no event exceed the purchase price
of the goods specified hereon.
TOOLS REQUIRED
• Level • Personal Protective Eyewear
• Hammer • Carbide tip drill suitable for tile
• Stud Finder • Protective blanket
• Center Punch
HealthCraft Products Inc., Toll Free 888-619-9992.
2790 Fenton Road, Ottawa, Ontario, Canada, K1T 3T7.
Invisia™Wall Toilet Roll Holder
FASTENERS: INSTALLATION & MAINTENANCE
The Invisia™ Wall Toilet Roll Holder must be secured to the
wall with fasteners appropriate to the structural material.
Included are 2 sets of mounting hardware for different wall
applications. Inspect, or have inspected (and tighten if
necessary) the screws on a monthly basis. See Page 3 for
structural reinforcement suggestions. Supplied
SnapToggles® can be used as an alternative to structural
reinforcement - ONLY if the walls have not been
compromised and are judged to be suitably structural (1/2"
drywall, or tile walls on 1/2" min cement board).
TIPS FOR DRILLING INTO TILE
• Use carbide tipped masonry drill on ceramic, or consider a
diamond tip drill for porcelain tile.
• If possible, drill a smaller pilot hole first.
• Be careful to prevent the drill from moving when you first
start it rotating - use duct tape or a wood guide on the
surface of the tile to hold the drill from walking sideways.
• A variable speed drill on slow is best to start the hole. Do
not apply too much pressure when drilling. Do not use a
hammer drill.
WATERPROOFING
We recommend that sealant be applied around the wall
contact points for any products mounted in the shower. If not
properly sealed, there is the potential for water to seep into the
wall. This may cause the wood to rot, thus compromising the
structure the support rail is attached to.
SOLID SURFACES: CLEANING AND MAINTENANCE
The tray is made from a durable, non-porous, solid surface
material that resists the growth of bacteria. Clean with general
household cleaners. The surfaces & edges can be sanded
and buffed to repair if necessary.
DC155 REV B Page 4 of 4
Specifications subject to change without notice.
WTRH200 (BN/CRP/PCW)
Weldment, Handle, WTRH
HealthCraft Products Inc., Toll Free 888-619-9992.
2790 Fenton Road, Ottawa, Ontario, Canada, K1T 3T7.
x4
x4

DC155 REV B Page 2 of 4
Specifications subject to change without notice.
A1. Secure the base to the rail with the supplied flat head
bolts and hex key. See Figure 4 for proper orientation.
A2. Mark the horizontal and vertical location of the Invisia™
Wall Toilet Roll Holder (if possible, line up the center hole of
the wall plate with the wood stud - use snap toggles for
outside holes if applicable). Use a level that spans the Wall
Toilet Roll Holder to ensure the rail is straight as shown in
Figure 2.
HealthCraft Products Inc., Toll Free 888-619-9992.
2790 Fenton Road, Ottawa, Ontario, Canada, K1T 3T7. DC155 REV B Page 3 of 4
Specifications subject to change without notice.
HealthCraft Products Inc., Toll Free 888-619-9992.
2790 Fenton Road, Ottawa, Ontario, Canada, K1T 3T7.