Solos SD-C147 User manual

6
5
1
2
7
3
4
Component list
61
3141
71
1222
52
No. Part Qty No. Part Qty
No.
Part Qty No. Part Qty
No. Part Qty No. Part Qty
No. Part Qty
Feet Lifting Column
Side Bracket
Hand Switch
(Option)
Power Plug
Supporting Beam
(Control Box included)
Cable ManagementTray
A
C
D
4
B
E
4
F
16
12
8
Accessory list
No. Image Spec Qty
Attention:The drawings below are for guidance only and they may differ
slightly from the product and fittings received. Please contact our customer
service department should you have any queries.
Allen Key
0.16"x0.16" 1
M6
St4.2
M6
M6
M6
276 lbs
3
Column Stage
Technical data
Max. Weight Capacity
Height Range
Width Range
22.8"-48.4"
43.3"-74.8"
SKU: SD-C147
SOLOS Advanced Standing Desk User Manual

5
F
A
A
5
4
STEP 1 Install the Side Brackets
screws(A) as show with the
Attach the side brackets(5) to the ends of the supporting beam (4) using
Allen Key(F).
Ax4
4
D
F
2
Install the Lifting Columns
STEP 2
Insert the lifting columns (2) into the ends of the supporting beam(4).
Fix the lifting columns using screws(D) with theAllen Key(F).
Dx8
C
F
1
2
Install the Feet
STEP 3
Place the feet(1) on the bottom of the lifting column(2).
Fix the feet using screws(C) withAllen Key(F).
Cx8
F
0.16"x0.16"
F
0.16"x0.16"
F
0.16"x0.16"

6
7
STEP 5 Install the Control Panel
Port for
hand switch
Power port
Port for cable
connected to the
lifting column
2
1
E
E
STEP 4 Install the Tabletop
The expansion distance of the
supporting beam can be adjusted
according to the actual use.
Attention: When the supporting beam is greater than 1720mm,
the installation method is as follows: Method 2 in Step 6.
Ex12
Loosen
Adjust
Tighten
F
0.16"x0.16"
3
Tighten
2
Buckle the other side
Allen Key (F).
1
Slide one side
3
4
B
STEP 6
Install the Cable
ManagementTray
Method 1
Firstly
with
, rotate the screws (B) incompletely into the supporting beam (4)
Allen Key (F), which means do not tighten them. Next, slide one
side of the cable management tray (3) into the screws (B), then the
other side Finally, tighten the screws (B) with
B
x4
F
0.16"x0.16"

Common fault treatment
g
The following tips w ill help you detected and e liminate the common fault
and error.If the fault you met is n ot lis ted below, ple as e contact with your
s upplier. Only themanufacturer and profes s ionals a re capable for inves tigatin
and correcting thos e fault and e rror.
1.Che ck if all the cables b e connected well
1.Che ck if all the cables b e connected well
2.Contact your s upplier or dealer
2.Contact your s upplier or dealer
1. Che ck i f overloaded, max l oading: 220 lbs;
1. Check if overloaded, m ax l oading: 220 lbs;
1. Check if overloaded, m ax l oading: 220 lbs;
2. Contact your s upplier or deale r
2. Contact your s upplier or deale r
2. Contact your s upplier or deale r
1. Contact your s upplier or dealer
1 .Re pos itio n
2.Contact your s upplier or dealer
（Duty cycle : Max 2min o n/18min OFF）
1. Re s tart afte r s us pe nd for 1 8mins w hile
c onnecting with power;
2. Contact your s upplier or dealer;
1. Pres s "M"and "3" togethe r for 3 s econds o r
more, a fte r he aring continuous b ee ping for twice ,
it will res tore factory s ettings
2.Contact your s upplier or dealer
Go down but not go up
The motor not move as instructed
Rising In a low Speed
No response while pressing up
arrow/down arrow after connected
with a power supply
No response while long pressing up
arrow/down arrow after connected
with a power supply
Downward Sliding
Frequently Reposition
Overwork
Not enough up& down height
Method
Fault Phenomenon
ionAttent
1. Power supply: AC100V-240V,50/60Hz
2. Service Environment: 0-40
3. Unplug the power plug before cleaning, wipe the dust on surface with slight wet
dishcloth when cleaning, be careful not to let the drops into the internal parts, not loose
the connector.
4. The electric box contains electronic components, metals, plastics, wires etc., so
dispose of it in accordance with each country's environmental legislation, not the
general household waste.
5. Check carefully to ensure correct and complete assembly before using.
6. Be familiar with all functions and program settings of the product before first use.
7. Children are forbidden to play on the product because of unforeseen action when
playing, so any dangerous consequences caused by this improper action will not be on
8. Slight noise caused by the V-ribbed belt or brake system due to structure will not
have any effect on the use of the equipment.
9. Corrosive or abrasive materials are forbidden to clean the equipment. Must ensure
that the cleaner used will not pollute the environment.
10. This appliance can be used by children aged from 8 years and above and persons
with reduced physical, sensory or mental capabilities or lack of experience and
knowledge if they have been given supervision or instruction concerning use of the
appliance in a safe way and understand the hazards involved. Children shall not play
with the appliance.
11. Cleaning and user maintenance shall not be made by children without supervision.
12. If the supply cord is damaged, it must be replaced by the manufacturer, its service
agent or a similarly qualified person in order to avoid a hazard.
13. Please make sure there is no hazard sources in your operating environment. e.g.,
do not litter the tools around.Always be careful to treat the packaging materials in order
to avoid any possible danger , e.g. plastic bag may lead to choking hazard to children.
14. Keep the original package of the equipment if necessary in case of the future use in
transportation.
°C
Waste disposal This marking indicates that this product should
not be disposed with other household wastes.
To prevent possible harm to the environment or
human health from uncontrolled waste disposal,
recycle it responsibly to promote the sustainable
reuse of material resources. To return your used
device, please use the return and collection
systems or contact the retailer where the
product was purchased. They can take this
product for environmental safe recycling.
3
4
D
B
B
D
Method 2
Install the cable management tray as Method 1, Step 6.
When the supporting beam stretches over 1720 mm,
the cable management tray needs to be mounted on
the middle of the supporting beam.
Do not stretch the support
beam beyond this hole
Dx4
Bx4
F
0.16"x0.16"