Heart of House Pin tuck oatmeal chair 532/3885 User manual

pin tuck oatmeal chair
Assembly Instructions - Please keep for future reference
Issue 1 - 5/04/16
Dimensions
Width - 56cm
Depth - 68cm
Height - 91cm
532/3885
549/7591
If you need help or have damaged or missing parts, call the Customer Helpline:
Argos = 0345 640 0800
Important - Please read these instructions fully before starting assembly

1
• Check you have all the
components and tools listed on
the following pages.
• Remove all fittings from the
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Make sure you have enough
space to layout the parts before
starting.
• During assembly do not stand
or put weight on the product, this
could cause damage.
• Assemble the item as close to
its final position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your floor.
• Parts of the assembly will be
easier with 2 people.
• We do not
recommend the
use of power
drill/drivers for
inserting screws,
as this could damage the unit.
Only use hand screwdrivers.
• Unit weight: 10.5 kgs.
• Maximum safe weight of user:
110kgs.
Safety and Care Advice
Important - Please read these instructions fully before starting assembly
Care and maintenance
Handy Hints
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• From time to time check that
there are no loose screws on
this unit.
• Do not stand on the chair.
• Do not use this chair as step
ladder.
• This product should not be
discarded with household
waste. Take to your local
authority waste disposal centre.
• Assemble all parts and bolts
loosely during assembly, only
once the product is complete
should you fully tighten the
bolts.
• Regularly check and ensure
that all bolts and fittings are
tightend properly.

2
Please check you have all the parts listed below
Backrest
(92 x 55.5 x 35cm)
1Seat
(57 x 48 x 15cm)
2Leg x 2
(43.5 x 4.5 x 3.5cm)
3
Components - Fittings
Please check you have all the fittings listed below
M8 x 65mm Bolt x 4
Note: The quantities below are the correct amount to complete the assembly. In some cases more fittings
may be supplied than are required.
A
Ruler - Use this ruler to help correctly identify the screws
0 15 30 45 60 75 905 20 35 50 65 80 9510 25 40 55 70 85 100 120 140105 125 145110 130 150115 135 155 160 165 170
Flat washer x 11
D
Spring washer x 11
C
E
M8 x 55mm Bolt x 7
B
Allen key x 1
F
Foot pad x 4
Components - Parts If you have damaged or missing components, call the
Customer Helpline: Argos = 0345 640 0800

3
Assembly Instructions
Step 1
Attaching legs
Place the seat upside
down on a flat protected
surface.
Insert the legs into the
holes of the seat as
shown and fix using bolts
, spring washers
and washers .
Important:
Fasten bolts
using allen key
but do not fully
tighten at this
stage.
Use oval head of
allen key on tight
angles.
2
3
A
F
C
D
Step 2
A
D
C
A
D
C
3
2
A
D
C
A
D
CAD
C
AD
C
3
2
3
Dust cover
2
Opening dust cover
Place the seat on a
flat protected surface.
Carefully peel off dust
cover of seat by pulling
the cloth from the back
side of the seat as
shown.
2

Assembly Instructions
Step 4
Attaching dust cover
Attach the dust cover to
seat as shown and
fasten by sticking to edge
of seat.
4
B
D
C
1
2
B
D
C
1
2
Dust cover
E
3
E
E
E
E
3
1
3
Remove backing from
foot pads and carefully
position on the bottom of
the legs & as
shown.
E
1 3
Step 3
Attaching the seat
Place the backrest on
a flat protected surface
as shown.
Position the seat on
the backrest as shown
and fix using bolts ,
spring washers and
washers .
Important:
Fasten bolts
using allen key
but do not fully
tighten at this
stage.
Use oval head of
allen key on tight
angles.
1
2
B
F
D
C

Assembly Instructions
a:
b:
c:
Aligning & securing the
legs
Carefully turn the chair
upright and place on a
flat surface.
a: Tighten all bolts using
allen key .
Note:
Use oval head of allen
key on tight angles.
Note: This step is
essential to prevent the
chair from wobbling due
to uneven legs.
b: Carefully sit on the
chair and make
adjustments to ensure
the legs are flat even on
the floor.
c: After the sitting test,
re-tighten bolts again if
any adjustment is
needed.
Note: It is highly
recommended to
re-tighten all bolts after
using the chair for 7
days.
Note: Keep allen key to
re-tighten bolts when
required.
Assembly is complete.
F
Step 5
5
F
F
If you need help or have damaged or missing parts, call the Customer Helpline:
Argos = 0345 640 0800