Hearth and Home Technologies GV60BK User manual

Hearth & Home Technologies • Grand Vista Mesh Doors • 4060-026 Rev F • 03/23 1
tm
tm
Models:
Grand Vista 60, Grand Vista 80, Grand Vista 100
Mesh Door Kits
Installation
Instructions
These mesh door kits have been tested for use with specic Hearth & Home Technologies products. Check with your local
building code agency before you begin installation to ensure compliance with local codes, including the need for permits
and follow-up inspections. If you encounter any problems regarding code approvals, or if you need clarication of any of
the instructions contained here, contact your Hearth & Home Technologies Inc. dealer. For the dealer nearest you, please
visit www.hearthnhome.com.
WARNING
Hot screen/mesh and glass doors will cause burns.
• Do not touch screen/mesh or glass doors until cooled
• NEVER allow children to touch screen/mesh or glass
doors
• Keep children away
• CAREFULLY SUPERVISE children in same room as
replace.
• Alert children and adults to hazards of high
temperatures.
High temperatures may ignite clothing or other
ammable materials.
• Keep clothing, furniture, draperies and other ammable
materials away.
HOT SURFACES!
Screen/mesh, glass doors and
other surfaces are hot during
operation AND cool down.
NOTICE: All ngerprints and smudges must be wiped clean
from the viewable surfaces of the door kit prior to the initial
burning of the replace. If this is not done, these prints and
smudges will be cured into the nish and set for the life of
the replace. To keep the nish looking its best, gently wipe
with a soft cloth and if desired, soap and water. Never use
thinner or abrasive cleaners since these products will damage
the nish.
CAUTION! Risk of Cuts/Abrasions. Wear protective
gloves and safety glasses during installation. Sheet metal
edges are sharp.
Upper
Mounting Bracket
Lower
Mounting Bracket
Mesh Door Assembly
Figure 1 Grand Vista Mesh Door
Door Model Number For Use on Models
GV60BK I60CT I60H EXCLAIM-36T EXCLAIM-36H SB60 SB60HB
GV80BK I80CT I80H EXCLAIM-42H EXCLAIM-42T SB80 SB80HB Legacy42-IFT Phoenix42-IFT
GV100BK I100CT I100H EXCLAIM-50T EXCLAIM-50T SB100 SB100HB

Hearth & Home Technologies • Grand Vista Mesh Doors • 4060-026 Rev F • 03/23
2
CAUTION! The door kit is heavy. We recommend two
installers to put the front assembly in place.
Installation:
1. Remove the existing screens from the replace.
See Figure 2:
• Remove one screw in each of the screen rods
behind the upper screen cover
• Slide screen rods out of support holes.
• Rods and screen will come out as an assembly.
• Discard.
2. Remove all but the two screws (aligned with the slots
on the upper mounting bracket) securing the upper
screen cover, see Figure 2. Save screws for Step 6. If
installing on ICON Series skip steps 3 and 4.
3. Remove (4) screws, securing lower screen cover,
see Figure 2.
4. Install lower mounting bracket, see Figure 1, using
the screws removed in Step 3.
5. Remove (3) wingnuts, (4) on GV100, and the
mounting bracket from the frame assembly.
See Figure 3. Set aside for Step 9.
6. Slide mounting bracket slots, see Figure 3, over the
two remaining screws of the screen cover, tighten and
secure in place with the screws removed in Step 2.
7. Remove the doors from the frame assembly.
8. Lift frame assembly and slide bottom ange, see Figure
3, over the lower screen cover.
9. Attach frame assembly to the upper mounting
bracket and tighten wingnuts.
• ICON Series: The bottom ange should t
between the lower screen cover and the hearth
stone.
• LEGACY42-IFT & PHOENIX42-IFT: The bottom
ange should t between the lower screen cover
and lower mounting bracket installed in Step 4.
10. Press the top of the frame assembly against the
upper mounting bracket. The threaded studs of the
frame assembly, see Figure 3, will t through the
matching holes of the upper mounting bracket.
Secure with wing nuts removed in Step 5.
11. Hang the doors on the frame assembly by
positioning the hinge pins of the door in the mating
hinge receivers. See Figure 3.
WARNING! Risk of Fire! DO NOT place combustible mate-
rials on the metal replace face or columns.
Slide handle
to the right to open
Wing
Nut (3)
Upper Mounting
Bracket
Threaded Studs (3)
Bottom Flange
Slots (2)
Figure 3 Frame Assembly
Screen Rod Screws
Upper Screen Cover
Lower Screen Cover
Figure 2 Remove Existing Screens
Figure 4 Completed Mesh Door Installation
►